Ikea Refrigerator Parts

Fix frost buildup on freezer walls and noisy fan operation. This defrost heater melts ice from evaporator coils during the auto-defrost cycle. DIY repair.

Catches drips and splashes in the dispenser recess of your refrigerator door. Replace if cracked, stained, or missing to keep the front panel clean.

Covers and protects the ice container in your refrigerator. Replace if cracked, broken, or missing to keep ice fresh and prevent contamination.

Secures and shields the freezer light assembly. Replace if cracked, broken, or missing to restore proper light protection and a clean appearance.

Ice not dispensing or leaking from bin? This ice bucket assembly holds ice and houses the auger. Fixes cracked housings affecting cube/crush selection.

The Mullion is an OEM part for Frigidaire refrigerators. It is situated between the freezer and refrigerator doors to separate the two compartments. The mullion provides structure, sealing the doors against air and temperature leakage.

Causes of a bad mullion can include wear and tear over time, damage from frequent door opening and closing, or impact damage.

Symptoms of a bad mullion include:

• Air and temperature leakage between compartments
• Difficulty closing one or both doors securely
• Gaps or cracks seen around the mullion frame
• Scratches, dents or other physical damage

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This turntable roller assembly sits under the glass tray to support and guide it as it rotates. Replacing a worn or damaged ring helps restore smooth tray movement for more even heating and dependable microwave performance.

• Supports the glass tray and allows smooth, consistent rotation
• Helps prevent tray wobble, binding, or scraping noises
• Can address issues like the tray not turning or uneven cooking
• Replaces cracked, warped, or missing roller rings

• Disconnect power before servicing
• Remove the glass tray, lift out the old ring, and clean the cavity floor
• Place the new ring wheels-down, seat the tray on the coupler, and test rotation
• Do not operate the microwave without the roller ring and tray properly installed

Mounts to the bottom hinge to limit door swing angle. Replace if your refrigerator door opens too far, hits the wall, or the bracket is bent or broken.

LED light bulb for refrigerator and freezer compartments. Replace when lighting fails or dims. Verify fit by checking your model number compatibility.

This replacement cover shields and finishes a designated area of your appliance, protecting internal components from dust, moisture, and accidental contact. Replace a cracked or missing cover to maintain proper operation and a clean, finished look.

• Protects internal parts from debris and moisture intrusion
• Restores intended airflow/containment and component protection
• Helps reduce rattles or vibration from loose or broken trim
• Common signs it's needed: cracks, broken tabs, loose fit, or exposed components

• Disconnect power; also shut off water supply
• Retain and reuse original screws/clips unless your model specifies otherwise
• Align tabs and mounting holes carefully to avoid stress on plastic
• Do not overtighten fasteners; snug by hand to prevent cracking

Internal cam that assists with smooth, secure refrigerator door closing. Replace if worn, cracked, or broken to restore proper door operation.

Replacement center hinge for refrigerator doors. Mounts between upper and lower doors to provide support and alignment. Replace if cracked or worn.

Joins sections of your refrigerator's water line for the dispenser and ice maker. Replace when the original coupling is cracked, damaged, or leaking.

This electronic control board is the central module that runs your dishwasher's cycles. It controls power and timing so the unit fills, washes, drains, and dries correctly—restoring normal operation when the original board has failed.

• Manages cycle timing and options, routing power to the wash motor, drain pump, water inlet valve, and heating circuit
• Interfaces with sensors and the door latch to start and advance cycles
• Monitors faults to help protect components and ensure proper operation

• Disconnect power at the breaker and verify no voltage before service
• Access location varies by model
• Use ESD precautions; move connectors one at a time to the matching terminals
• After reassembly, run the unit's diagnostic/service cycle per the tech sheet to verify operation

Channels ice from maker to dispenser opening. Replace if cracked, broken, or missing to prevent ice scatter and jams. Installs in freezer door dispenser.

Covers the lower front of your refrigerator in midnight gray. Replaces cracked, broken, or missing grilles to restore airflow and a finished look.