Ikea Refrigerator Parts

The Hinge-Door is an OEM part for Whirlpool refrigerators. The refrigerator door hinge is a crucial component that allows the door to properly open and close while securely holding it in place. These hinges are responsible for smooth and reliable door operation through thousands of openings and closings. 

Causes of a bad hinge can include wear and tear from prolonged use, stress from overloading the door, or accidental impact damage. 

Symptoms of a bad hinge include:

• The door not closing properly or staying fully shut  
• Difficulty or resistance when opening/closing the door
• The door sagging or wobbling excessively
• Noise or grinding sounds coming from the hinge area

This OEM Whirlpool replacement part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Restore a tight, even seal between your refrigerator's doors. This vertical mullion assembly flips into place to cover the center gap, helping maintain proper temperatures and reduce condensation.

• Bridges the gap between doors to create a continuous sealing surface
• Helps keep cold air in and warm air out for consistent cooling
• Aids proper door alignment and smooth closing
• Common symptoms of a failed mullion: broken or wobbly flipper, doors not closing fully or popping open, moisture/icing at the center, warming in the fresh food section

• Disconnect power before servicing and open the doors
• With the door open, release the retaining screws or tabs and lift the old mullion off the upper and lower pivots
• Position the new assembly on the pivots, secure it, and verify the flipper moves freely and seals evenly against the opposite door
• Restore power and recheck door operation and gasket contact along the full height

Ice not dispensing or leaking from bin? This ice bucket assembly holds ice and houses the auger. Fixes cracked housings affecting cube/crush selection.

Fix refrigerator temperature issues, display failures, or defrost problems. This control board manages cooling cycles and temperature settings.

Catches drips and splashes at the base of your refrigerator's ice and water dispenser. Replace this tray if it's cracked, broken, or missing.

This ice maker shut-off arm is the wire lever that detects the ice bin level and stops production when raised. Replace a bent, broken, or missing arm to restore reliable on/off control of your icemaker.

• Monitors bin fullness; in the up position it opens the internal switch to pause ice making
• Lowers as ice is used so the icemaker can resume cycles
• Restores manual shutoff when you lift the arm

• Disconnect refrigerator power and turn off the water supply before servicing
• Remove the ice bin for access; open the icemaker front cover if your model has one
• Pull the old arm straight out of the pivot holes; align and fully seat the new arm so it moves freely
• Restore power and lower the arm to resume ice production; the arm raises and stops production when the bin is full

Color: Midnight Grey

Fix frost buildup on freezer walls and noisy fan operation. This defrost heater melts ice from evaporator coils during the auto-defrost cycle. DIY repair.

The Mullion is an OEM part for Frigidaire refrigerators. It is situated between the freezer and refrigerator doors to separate the two compartments. The mullion provides structure, sealing the doors against air and temperature leakage.

Causes of a bad mullion can include wear and tear over time, damage from frequent door opening and closing, or impact damage.

Symptoms of a bad mullion include:

• Air and temperature leakage between compartments
• Difficulty closing one or both doors securely
• Gaps or cracks seen around the mullion frame
• Scratches, dents or other physical damage

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

Mounts to the bottom hinge to limit door swing angle. Replace if your refrigerator door opens too far, hits the wall, or the bracket is bent or broken.

This spigot routes water from the internal supply to the dispenser outlet, delivering a controlled stream. Replacing a cracked or worn spigot helps restore proper dispensing and reduces drips or leaks at the dispenser area.

• Directs water from the internal tubing/reservoir to the dispenser outlet
• Maintains a defined flow path to help prevent splashing and after-drip
• Common symptoms of failure: dripping at the dispenser, slow/erratic flow, leaks inside the door, or visible cracks at the outlet
• Replace if damaged, leaking, or obstructed by mineral buildup

• Unplug the appliance and shut off the household water supply
• Dispense water to relieve line pressure before replacement
• Access the dispenser; note tubing orientation and fully seat/secure connections
• Restore water and power; flush the system and check all joints for leaks

Replace your refrigerator's cracked or missing base grille. This toe kick panel mounts across the bottom front to restore a finished look and protect components.

Illuminates your refrigerator's ice and water dispenser area. Replace if light is dim, flickering, or out. Confirm fit with your model number.

Fix uneven cooling or icing issues with this refrigerator air damper diffuser. Distributes cold air between compartments. Simple DIY repair, 30 min.

Secures and shields the freezer light assembly. Replace if cracked, broken, or missing to restore proper light protection and a clean appearance.

Catches drips and splashes in the dispenser recess of your refrigerator door. Replace if cracked, stained, or missing to keep the front panel clean.