Need Help?
Call or text
Dryer won't shut off or timer won't advance? This control timer manages cycle duration and prevents continuous running. Moderate DIY repair.
Replaced the timer - This should have been a VERY easy repair however, there is a clip (holding the timer to panel) on the bottom of timer than must be removed with a pair of pliers. There is absolutely NO room to access this clip so I had to take apart much of the dryer to gain access. What should have been a 15 minute repair turned into a frustrating hour. Read more
Fix a dryer that won't start, stops mid-cycle, or runs too long. Replacing a faulty timer is straightforward—snap in the new part after unplugging.
Replaced timer. It's a snap in place timer, once you remove the defective timer, overall pretty easy. Read more
Front drum felt seal prevents clothes from catching between the drum and dryer interior. Replace if worn or damaged. Confirm fit with your model number.
Took the whole dryer apart to access the wheels (4) of them, belt and fan wheel, also had to clean all the lint out that somehow builds up inside the dryer. Plus cleaned out dryer duct vent, added to the time involved. If you are planning on fixing the dryer because of a noise which was in my case, I highly recommend buy all the parts for complete maintenance mentioned above. What helped save me time? I watch a dryer fan wheel replacement training video first, highly recommend this!... Read more
The Fabric Softener Dispenser is an OEM replacement part specific to Whirlpool washing machines. It is responsible for accurately dispensing the appropriate amount of liquid fabric softener during the rinse cycle to soften and protect clothes.&nb
I purchased part #85753076A, Whirlpool Fabric Softener Dispenser. Popped off the top from the agitator and popped on the fabric softener dispenser. It took me less than a minute and it works perfectly! No more missing the rinse cycle!!! Read more
The Knob is an OEM replacement part for Whirlpool washers and dryers. The control knob lets you control cycle settings. Remove the knob by pulling it straight off its post. Causes of a bad knob can include wear and tear over time resulting
I followed YouTube for instructions. Had a slight problem removing stems, but got it done. Read more
The heater box houses your dryer's heating element and screen. Replace this component when rusted, corroded, or the screen is damaged causing snags or stains.
Replaced the heater tube. Had to open the back up, removed the heating element and then replaced the heater tube. Then I put it all together again and everything is fine now. Read more
The Front Panel Seal is an OEM replacement part for Whirlpool dishwashers. Measures 24 inches. This seal is located on the dishwasher's front panel and helps prevent water leaks by creating a watertight barrier during the wash cycle. It ensures eff
First I watched videos about squeaking Kenmore dryers. Then I used that information to open the dryer, diagnosing the fact that the roller on the drum belt tension arm had broken and actually fallen off the arm. The dryer was filled with lint and dust/dirt, so I also saw that the seals on the dryer had deteriorated greatly. AppliancePartsPros website is outstanding, far better than its competitors. This made it easy to find the parts and videos that I needed. It took hours to pull everything... Read more
Washer not draining or leaving standing water? A faulty water pump often causes drainage problems. DIY repair with basic tools in under an hour.
Replaced pump Read more
Protective cover that encloses the drive belt and motor pulley. Replace yours if cracked, warped, worn through, or missing to shield moving parts.
There was a horrible screeching noise coming from the washer, and upon inspection I found that the retaining nut that attaches the cam to the machine was either improperly tightened to begin with or had worked itself loose causing the cam to wobble and the belt to work down the cam. The cam gear teeth became worn and the belt worked itself half off the cam and cut a hole in the protective plastic screen containing the whole ensemble. I purchased the belt, shield and cam kit. The parts are... Read more
The Push to Start Switch is an OEM replacement part for Whirlpool dryers. Located on the control panel, it allows the user to initiate the drying cycle with the push of a button. This switch is designed to withstand the repetitive motions of starting c
I replaced the part i ordered and it worked great! Read more
Dryer won't heat or stops working? A burnt or melted terminal block disrupts power flow. DIY repair in under an hour with video guidance included.
I ordered the parts through AppliancePartsPros.com. They were delivered the next day. I installed them and the dryer works great. Read more
Flexible drain hose routes water from washer tub to household drainage. Replace if cracked, leaking, or deteriorated from age and flexing wear.
Replaced hose that came with the new washer with this longer one. Read more
If your washer won't start or the motor hums but doesn't spin, the capacitor may have failed. This part regulates electrical current to the motor.
Tested capacitor Read more
Includes screws and wire connectors. For the complete terminal block kit use 279320.
Plastic trim bezel that mounts around the lid lock on your top-load washer's panel. Replace if cracked, broken, or missing to restore a clean finish.
Put in new lid lock. This is my second one in 1 year. Whirlpool suggested I leave it loose so that if somebody did try and force it open, it wouldn't break it. This lid lock has 4 wires and cannot be bypassed. Read more
Stationary rack installs inside the dryer drum to dry items flat without tumbling. Replace your cracked, broken, or missing rack for sweaters and shoes.
Reasonable price for dryer rack and fast delivery = excellent customer service; will buy again Read more