Inglis Parts

The Water-Level Pressure Switch is an OEM part for Whirlpool washers. It is responsible for monitoring the water level inside the washer's tub during different cycles. This switch detects changes in air pressure as the water level rises or falls, communicating these variations to the washer's control board. 

Symptoms of a faulty water-level pressure switch include:

• Incorrect water levels during the wash cycle
• Washer not filling or draining properly
• Error codes related to water level

A bad water-level pressure switch can occur due to various factors, such as clogs or blockages in the air hose, a malfunctioning switch mechanism, or electrical issues. If you notice problems such as the washer not filling or draining properly, water levels that are too high or too low, or error codes related to water level, it may be time to replace the water-level pressure switch.

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.
 

This bleach dispenser for a washing machine holds liquid bleach and releases it into the tub at the appropriate point in the cycle, helping dilute bleach and protect fabrics from contact with undiluted solution. What it does:

• Holds and meters liquid bleach until the machine calls for dispensing
• Helps ensure bleach mixes with water for even, diluted distribution
• Replace if cracked, clogged, or leaking
• Common symptoms include bleach not dispensing, bleach left in the cup, leaks around the dispenser area, or bleach spots on fabrics

• 1 bleach dispenser

• Disconnect power and turn off water before servicing
• Access and mounting vary by model; follow your service manual to reach the dispenser
• Detach hoses/clamps or fasteners, transfer any reusable hardware, and seat the new dispenser fully
• Reconnect, then run a test fill/rinse to check for proper dispensing and leaks

This sensor monitors humidity inside the microwave cavity so sensor-cook and reheat features can automatically adjust time and power. Replacing a failing sensor restores accurate automatic cooking and helps prevent premature shutdowns or "Sensor" error messages.

• Detects steam/humidity in the cavity during sensor-based cooking cycles
• Sends feedback to the control to optimize cook time and power levels
• Failure can cause "Sensor" errors, sensor-cook cycles that won't start or end early
• Manual timed cooking may still work while sensor-cook modes misbehave

• Disconnect power before servicing; microwaves contain a high-voltage capacitor that can retain a dangerous charge
• Access is typically behind the top grille/control area; note sensor orientation before removal
• Handle the sensor by its body; avoid contaminating the sensing face
• Route wiring as original and ensure the connector is fully seated before reassembly

This part is a genuine OEM replacement drive motor. It is intended to replace a broken or faulty motor in various washers.This motor drives the washing machine, allowing the drum to rotate and agitate when the user selects the desired settings. Over time, the motor might become worn or start to malfunction, requiring immediate replacement. Before starting the repair process, unplug the appliance from the power source and check the resistance running through the motor windings using a multimeter. If the meter measures infinite resistance, the drive motor will definitely need to be replaced. Work gloves should be worn to prevent injury.This part has been made by Whirlpool and has been sourced directly from the manufacturer. This part is made out of high-quality, durable, non-corrosive materials to ensure high quality and is sold individually. It is compatible with washing machines manufactured by Whirlpool, Maytag, Jenn-air, and various other brands.

This lens covers and diffuses an appliance light source, protecting it from heat, grease, and moisture while delivering even illumination. Replacing a cracked or yellowed cover restores brightness and a clean, finished look.

• Shields the bulb or LED from debris, grease, and impact
• Diffuses light for more even, glare-free illumination
• Helps maintain the appearance of the light area
• Common symptoms: cracked, broken, missing, discolored, or loose lens

• Disconnect power and let the lamp/surface cool before servicing
• Support the old lens while removing any retaining screws or clips
• Align tabs or holes carefully; seat the new lens fully and evenly
• Do not overtighten fasteners to avoid cracking the lens

This drying rack sits inside the dryer drum to hold items stationary for tumble-free drying. It's ideal for shoes, sweaters, and other delicate pieces that need air circulation without bouncing or spinning, helping prevent damage and excess noise. What it does:

• Provides a stable surface for no-tumble drying inside the drum
• Helps prevent scuffs, stretching, and wear on delicate items and footwear
• Replaces a missing, cracked, or warped rack
• Common signs you need a new rack: won't seat securely, bent or broken frame, or persistent rattling when in use

• 1 drying rack

• Unplug the dryer and allow the drum to cool before placing the rack
• Open the door and position the rack per your owner's manual so it sits level and secure
• Load items evenly; ensure nothing contacts the rotating drum
• Use only the rack-dry/low-heat/air cycles recommended for your model; remove the rack before normal tumbling cycles

STACK KIT FOR LONG VENT DRYER

This leveling foot stabilizes and levels your appliance on uneven floors. It threads into the base so you can raise or lower a corner, reducing rocking and vibration for smoother, quieter operation and proper alignment.

• Provides precise height adjustment to level the cabinet
• Helps prevent wobble, walking, or rattling during use
• Supports stable operation and proper door alignment
• Replaces a missing, stripped, or damaged foot

• Disconnect power; shut off gas/water if applicable
• With help, carefully tilt or brace the appliance to access the foot
• Thread the new foot in by hand, then fine-adjust with a wrench until level and stable
• Ensure all feet contact the floor; recheck level after positioning

This capacitor stores and releases electrical energy to give the appliance's circuit the boost and stability it needs to start and run properly. Replacing a weak or shorted capacitor can restore reliable operation and reduce strain on related components. What it does

• Provides an energy boost and stabilizes voltage in the designated start/run or power circuit
• Helps motors or power sections energize smoothly and maintain performance
• A failing capacitor may cause humming/buzzing, failure to start or heat, intermittent operation, or tripped fuse/breaker
• May show swelling or signs of overheating around the case or terminals

• 1 capacitor

• Disconnect power before service; capacitors can hold a charge—use a proper discharge procedure before handling
• Note/photograph wire locations; move leads to matching terminals and ensure tight connections
• Mount securely in the original position; re-use brackets/insulators as applicable and keep wiring clear of sharp edges or heat
• After replacement, check the related motor or circuit components if symptoms persist

This drain hose extension kit increases the reach of your appliance's drain line so it can connect to a farther standpipe or sink, supporting proper drainage and reducing stress on fittings that can lead to leaks. What it does:

• Extends the existing drain hose to accommodate installations where the drain connection is farther away
• Helps maintain a secure, leak-resistant connection when routed correctly
• Useful when relocating the appliance, changing cabinetry, or updating plumbing
• Common signs you may need it: hose won't reach, kinks when stretched, or occasional water near the drain line

• One drain hose extension kit

• Disconnect power and shut off the water supply; have a towel or pan ready for residual water
• Join the extension to the existing drain hose with the proper coupling/clamps; tighten securely and avoid kinks or sharp bends
• Route and support the drain line per your model's installation guide and observe any maximum total hose length
• Run a short test cycle and check all joints for leaks

This dryer power cord connects an electric dryer to a 4-prong household outlet. Replace a worn or damaged cord to restore a safe, reliable power connection and help prevent intermittent power or overheating at the cord connection. What it does:

• Connects an electric dryer to a 4-prong receptacle for proper power and grounding
• Four-conductor design supports modern installation requirements
• Replaces cords with cracked insulation, loose prongs, or burned terminals

• 1 dryer power cord

• Disconnect power at the breaker before servicing
• Attach to the dryer terminal block per the appliance's wiring diagram and secure the strain relief

This upper agitator—also called the clothes mover—is the top section of the agitator in select top-load washers. It works with the agitator cam and dogs to roll laundry over during wash strokes. Replace if cracked, stripped, or no longer engaging. What it does:

• Provides the upper vanes that lift and roll clothes for proper turnover during agitation
• Transfers one-way motion from the cam/dogs to the top section of the agitator
• Helps address symptoms like the top section free-spinning, poor turnover/cleaning, rattling/loose feel, or visible cracks/broken fins

• 1 upper agitator (clothes mover)

• Unplug the washer and turn off water before servicing
• Remove the dispenser and cap to access the center fastener; lift out the agitator assembly
• Separate the old upper section from the cam, seat the new clothes mover fully on the splines, and reassemble
• Hand-check for one-way engagement of the top section before running a test cycle

The Shock Absorber is an OEM part compatible with Whirlpool washing machines. It is a crucial component that helps reduce vibrations and dampens movement during the spin cycle. The shock absorber absorbs mechanical stresses to prevent the washer tub, suspension springs, and other components from wearing out prematurely.  

Causes of a bad shock absorber include wear and tear over time, cracks or breaks from heavy loads, or damage due to impact.  

Symptoms of a bad shock absorber include:

• Excessive shaking, vibration or noise during the wash and spin cycles   
• The washer walking or moving during operation
• Premature failure of other suspension parts like springs or the washer frame
• Potential leaks if movement stresses plumbing connections

This OEM replacement is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models. 

The Dryer Drum Baffle is an OEM replacement part designed for Whirlpool dryers. The baffle, located inside the drum, helps lift and tumble clothes during the drying cycle, ensuring even and efficient drying. It agitates the clothing, allowing air to circulate freely and preventing tangling.

Note: This is the tall baffle.

Over time, the drum baffle can become loose or damaged due to frequent use and contact with clothing or objects left in pockets. Physical wear or repeated impacts might cause it to crack, detach, or warp, reducing its ability to tumble clothes properly.

Symptoms of a faulty Drum Baffle include:

• Clothes not drying evenly or efficiently
• Unusual noises coming from the drum, such as rattling or banging
• Loose or detached baffle within the drum

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Shipping Bolt is an OEM part for Whirlpool washing machines. Located within the base frame, these bolts serve as anchoring points to secure the washer during product transport and installation. 

Symptoms of bad shipping bolts include:

• Loose footing or unstable/rocking movement of the entire washer unit
• Strange noises, like a clicking or rattling, coming from the base area  
• Difficulty leveling the legs or maintaining proper position

The causes of faulty shipping bolts are generally worn from repeated removal and reinstallation during service procedures. Corrosion over time can also degrade their integrity. 

Replacing with new OEM bolts from Whirlpool will securely anchor the washer going forward. This part is compatible with models from Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore. A stable base prevents potential issues or safety hazards.

This top hinge supports the hinged top or upper panel, allowing it to lift for service and close securely. Replacing a worn hinge restores smooth motion and proper alignment to help eliminate wobble, scraping, or gaps.

• Provides the pivot point for lifting the top/panel
• Maintains alignment and helps the top seat flat when closed
• Restores smooth opening/closing without binding or rubbing
• Common signs of failure: loose or uneven top, squeaks, difficulty lifting/closing, visible bending or cracks at the hinge

• Disconnect power; also shut off gas and allow all surfaces to cool
• Support the top/panel while removing and installing the hinge to prevent strain
• Transfer and tighten existing mounting screws unless new hardware is provided
• After installation, check alignment and clearances; replacing hinges in pairs can improve fit