Need Help?
Call
Washer water heater element raises water temperature during wash cycles. Replace if cracked, corroded, or no longer heating properly in your machine.
Secures washer tub during transport to prevent internal damage. Install in back panel before moving. Replace if missing, rusted, or corroded. Set of 4 required.
Secures washer base frame during transport and installation. Replace if bolt is lost, stripped, or damaged during delivery or moving to prevent rocking.
Replace a cracked or broken dispenser cover that exposes internal parts. This outer trim panel protects wiring and restores appearance. Easy hand removal.
Supports and pivots the hinged dryer top panel for service access. Replace if cracked, broken, or causing wobble, scraping, or alignment gaps.
Replaced belt and idler arm, just to be safe. Read more
Two 5-foot nylon braided hoses connect household water supply to washer inlet valves. Replace cracked, leaking, or aging hoses to prevent water damage.
Watched u tube video. Ordered replacement water inlet valve and new hoses. Dismantled washer and replaced defective valve and installed new hoses. The repair went very easily and the washer worked perfectly as a result. Read more
This is the fabric softener dispenser cup that fits inside the agitator or dispenser housing of a top-load washing machine. It holds liquid fabric softener and releases it into the wash water at the appropriate time during the rinse cycle. Replace this cup if it is cracked, warped, or clogged, or if fabric softener is not dispensing properly during the wash cycle.
Put the new one on. Read more
Door hinge pin assembly for dryers. Provides the pivot point for your dryer door, supporting its weight during opening and closing. Replace if bent or worn.
I had to unscrew the old hinges and replace with these new ones. Fit was perfect!! Read more
Adjustable leveling foot threads into washer or dryer base to stabilize appliance on uneven floors. Replace if cracked, worn, or missing to reduce rocking.
Relocates your dryer's exhaust vent from rear to left, right, or bottom. Includes elbows, duct, and instructions. Replace when changing installation.
Used the Wpl. Vent Kit, 4-way. This is not a quick, easy job. You have to disassemble the dryer, removing the entire front, door, drum, and control panel. Take your time and take pictures as you go so you can get it all back together again after installing the conversion kit. It will take you at least an hour, and you need room to work. Also, remember that after converting the dryer over to left or right vent, you now have a wider dryer with the ducting sticking out the side. (4") Make sure it... Read more
Contains two, six foot long braided hoses with 90 degree ends.
I had a problem with the drain pump on my Kenmore HE3 and I replaced it using a drain pump I ordered from APP. That fixed that problem but once I started running the washer I started getting a FH error code. I looked it up and found that it was a problem with the washer not filling properly. I pulled the washer out and found that one of the fill hoses had kinked when I pushed the washer back in place. There was also some writing on the hose that read "Change hose every five years". I know I had... Read more
Fix detergent mixing in your washer's dispenser with this drawer divider. Separates compartments for detergent, softener, and bleach. Easy 5-minute fix.
Internal washer drum component that directs water flow during wash cycles. Replace if cracked, broken, loose, or catching on clothing during agitation.
By replacing 1 Read more
Shield cap for laundry center washers. Covers and protects internal components. Replace if cracked, broken, or missing to maintain proper enclosure.
Washer won't spin or agitate? A failed drive motor is often the cause. This motor assembly restores drum rotation and agitation for reliable washing.
Dryer stops early on auto cycle but works on timed? The moisture sensor control board monitors dryness levels. DIY-friendly repair, 15-20 minutes.
Did some research via the internet and figured the problem was likely the moisture control board. Watched a video of the repair of a similar unit in order to locate the moisture control board. Used the chat feature with one of the Appliance Parts Pros to get a schematic of the dryer and advice about where to use the putty knife to release the springs for access to the board. Thanks to the lady I chatted with for expert advice. Once the actual task was started, the repair took 15 or 20... Read more
By continuing to use our site, you agree to our Terms of Usage and Privacy Policy. You can learn more about how we use cookies by reviewing our Privacy Policy.
We use cookies to optimize website functionality, analyze the performance, and provide personalized experience to you. Use the controls below to manage your privacy preferences.
Cross-Site Advertising
When enabled, we may use cookies and similar technologies to deliver personalized advertisements based on your browsing activity across different websites. Opting out will disable third-party advertising cookies on this site.
Analytics Sharing
When enabled, we may share anonymized browsing and usage data with third-party analytics providers to help us understand how visitors use our site. Opting out will prevent this data from being shared with third parties.