Jenn-Air Dishwasher Parts

The Dishrack Track (Right) is an OEM part for Whirlpool dishwashers. It is responsible for supporting the third-level dishrack and allowing it to glide in and out smoothly during the loading and unloading process. This track is designed specifically for the right side of the third-level rack. 

Causes of a bad track include damage from heavy use over time, such as dulling or bending of the metal track surface from repeated loading/unloading of dishes. Debris or residue buildup along the track can also cause issues.

Symptoms of a bad track include:  

• Rack that will not fully extend or retract
• Binding or sticking during rack movement  
• Rack that will not stay positioned above

This OEM Whirlpool replacement part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Drain Hose is an OEM part for Whirlpool dishwashers. It serves as the connection that allows dirty water to exit the dishwasher tub and flow into the water drain system after each wash cycle. The hose transports wastewater from inside the dishwasher out through the standpipe.

Causes of a bad drain hose can include mineral or food debris buildup blocking water flow within the hose, cracks or breaks in the plastic material from repeated bending, or a loose or damaged hose clamp connection.

Symptoms of a drain hose failure include:

• Standing water remaining in the bottom of the tub after a cycle
• Puddles or leaks developing near or underneath the dishwasher
• Water failing to properly drain during the designated drain portion of cycles
• Kinks or sagging appearing in the hose affecting water drainage

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

Color: White. 4oz bottle with brush used for touching up damage to your dishracks. For blue use W10840471. For grey use WP676455. For tips use 675679

This diverter disc directs wash water to different spray zones during a cycle, helping ensure alternating spray patterns and thorough cleaning. A worn or damaged disc can cause poor wash performance or incorrect spray routing.

• Routes water from the sump to selected spray arms/zones
• Helps alternate spray to improve coverage and cleaning
• Worn discs may lead to weak spray, poor cleaning, or unusual cycle behavior
• Can contribute to water leaking at the diverter area if the seal interface is compromised

• Disconnect power and water before servicing
• Access is typically from the bottom; remove the toe kick and lower panel as needed
• Note the disc orientation in relation to the diverter mechanism during removal
• Inspect related components (diverter motor/shaft, seals, sump) and replace if worn

This electronic control board is the central "brain" of your appliance. It manages power distribution, sensor inputs, and timing so selected functions run correctly. Replacing a failed board restores proper operation and reliable, responsive controls.

• Coordinates and sequences operations based on user selections and built-in programming
• Interprets inputs from sensors/switches and communicates with the user interface
• Drives components such as motors, pumps, valves, and relays as required
• Common symptoms of a failed board: appliance won't start or respond, cycle won't advance, stops mid-operation, intermittent behavior, or error/blinking status codes

• Disconnect power at the breaker or unplug the appliance before servicing
• Use ESD precautions; handle the PCB by the edges to avoid static damage
• Photograph wiring and transfer connectors one at a time to the new board
• Some models require service-mode setup or programming after installation—follow the tech sheet for your unit

This adapter tube assembly connects sections of the appliance's water line to create a secure, leak-resistant path for water flow. Replace it if the tube is cracked or the connection no longer seals properly to prevent leaks and restore flow.

• Connects water tubing between components within the appliance's water system
• Helps maintain a tight, leak-resistant seal at the joint
• Restores proper water flow when a tube or connector is damaged
• Typical symptoms: water leaking at the connection, reduced or no water flow, visible cracks/kinks, loose fit

• Disconnect power and shut off the water supply before servicing
• Relieve line pressure and place a towel or pan to catch any residual water
• Note routing and orientation before removal to ensure correct reassembly
• After installation, restore water and check all connections for leaks

This wax motor is the actuator for the dishwasher's rinse aid dispenser, releasing rinse agent at the correct time in the cycle. Replacing a weak or failed unit restores consistent rinse aid dispensing and helps minimize spotting.

• Actuates the rinse aid dispenser by extending a plunger when energized
• Works with the control to meter rinse aid during the final rinse
• Failure symptoms can include rinse aid not dispensing, the level never dropping, and increased spotting/filming on dishes
• Dispenser may remain closed with no audible actuation during the cycle

• Disconnect power at the breaker and shut off water before servicing
• Remove the door panel to access the dispenser; label and disconnect wires
• Release the old motor and install the new one in the same orientation, ensuring it seats fully
• Run a test cycle to ensure the dispenser releases rinse aid

Color: gray. Measures about 3-3/4 inches wide by a 1/2 inch high.

This electronic control board is the dishwasher's brain, managing cycles and powering the pump, valve, heater, and other loads. Replacing a failed board restores normal start, wash, drain, and dry functions.

• Coordinates and times wash cycles based on user selections and sensor inputs
• Sends power to the circulation pump, drain pump, water inlet valve, and heater
• Interfaces with the user interface and monitors door/latch status
• Failure may cause: no start, cycle won't advance or ends early, no fill/drain/heat, or error codes

• Disconnect power at the breaker before servicing; verify power is off
• Access location varies by model; commonly behind the lower toe panel or inside the console
• Handle the board by the edges and observe ESD (anti-static) precautions
• Move wire connectors one at a time from the old board to the new, secure the board, and reassemble; run any required diagnostics/reset per your model's tech sheet

The Top Spray Arm is an OEM part for Whirlpool dishwashers. It serves an important role on the upper rack, directing a spray of water across dishes during the wash cycle to thoroughly clean all surfaces. As a rotating component, the top spray arm endures constant motion which can cause wear over time.

Causes of a bad top spray arm include deterioration or cracks in the plastic from extended use, or blockages that restrict water flow.

Symptoms of a bad top spray arm include:

• Incomplete cleaning of upper rack dishes
• Buildup of food debris or grime that won't rinse away
• Noticeably weaker spray pattern from the arm nozzles

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

Color: Stainless   Note: Comes with Allen wrench, spare set screw, and instructions.

Dishwasher rack mounting strip roller.

Restore safe, smooth door operation with this dishwasher door spring. It counterbalances the door's weight so it opens and closes in a controlled way, preventing a sudden drop when the original spring breaks or fatigues.

• Provides the tension that counterbalances the dishwasher door through the hinge mechanism
• Helps prevent the door from slamming open or feeling unusually heavy
• Restores smooth, even door movement side-to-side
• Typical symptoms: door drops quickly, feels heavier than normal, uneven motion, or a visibly broken/stretched spring

• Disconnect power and shut off water before servicing
• Remove the toe/kick panel to access the hinge area
• Support the door, then move it slightly to relieve tension before unhooking the old spring
• Attach the new spring between the frame anchor and hinge arm; if your model uses two springs, replace both sides for even tension

This left-hand (LH) support is the factory replacement bracket that secures and aligns the left side of its assembly, helping keep parts level and operating smoothly. Replacing a damaged support restores proper fit and reliable function.

• Provides structural support and alignment on the left-hand (LH) side
• Helps keep connected components level and properly spaced
• Common symptoms: cracked/broken support, wobbling or sagging parts, misalignment, rubbing or binding during use
• Typical causes: wear, stress/impact, overloading, or overtightened fasteners

• Disconnect power before servicing; shut off water supply if applicable. Wear cut-resistant gloves.
• Clear the area for access. Note the original orientation and retain any screws/clips for reuse.
• Install the new LH support in the same position and ensure it aligns with the opposite side.
• Check fit and operation before fully reassembling.

The Rack Support (RH) is an OEM part for Whirlpool dishwashers. It is the plastic right-hand side bracket that secures the upper rack assembly inside the washer cavity. 

Causes of a damaged rack support include cracks or breaks from normal wear over extended use. Repeated impact from dishes loading/unloading can cause small stress fractures.

Symptoms of a faulty support include:  

• Loose or rattling upper dish rack during operation
• Difficulty sliding racks in/out smoothly
• Visible cracks or missing pieces on the support

This Whirlpool OEM part is also compatible with Maytag, Jenn-Air, KitchenAid, and some Kenmore models.

This dishrack replaces a damaged or rusted rack in your dishwasher. Restoring a true-to-spec rack keeps plates, bowls, and cookware secure and properly spaced so the machine can clean effectively and the rack moves smoothly on its tracks. What it does:

• Organizes and supports dishes and cookware during wash and dry cycles
• Maintains proper spacing for spray coverage and drainage
• Interfaces with the rail system to slide in and out when paired with the correct rollers/stops for your model
• Common symptoms: rusted or broken tines, deteriorated rack coating, misshapen frame, rack falling off tracks or not sliding properly

• 1 dishrack

• Disconnect power to the dishwasher before servicing
• Open the door; pull the existing rack out. For upper racks, release/remove rack stops or end caps; for lower racks, lift straight out
• Transfer any reusable components (rollers, clips, fold-down tines, silverware basket) from the old rack
• Slide the new rack onto the rails and reinstall stops; verify smooth travel before running a cycle