Jenn-Air Dishwasher Parts

This dishwasher wash impeller mounts on the circulation pump to drive water through the spray arms. A worn or damaged impeller can cause weak spray, poor cleaning, or noise; replacing it restores proper wash pressure. What it does:

• Moves water from the circulation pump through the filter and spray arms for effective cleaning
• Maintains proper wash pressure and spray action during the cycle
• Common fix for poor cleaning, spray arms not turning, or weak/no water circulation
• May reduce grinding or rumbling noises caused by broken or stripped impeller blades

• Includes 1 wash impeller

• Disconnect electrical power and shut off the water supply before servicing
• Remove the lower rack and spray arm; take off filters/sump cover to access the impeller
• Note impeller orientation; transfer any spacers as found and secure the impeller without overtightening
• Reassemble, check for leaks, and verify spray arm rotation after a test cycle

The Power Cord Kit is an OEM replacement part for Whirlpool dishwashers. It is a 3-prong grounded, 16-gauge cord that includes all the hardware needed for installation. Includes all hardware needed for installation.

Causes of a bad power cord can include normal wear and tear over years of use, accidental impacts or cuts to the wiring, or improper installation that damages components.

Symptoms of a bad power cord include:

• The dishwasher not turning on or completing cycles
• Warm or hot power cords during operation
• Frayed, cracked, or exposed copper wiring

This is a genuine Whirlpool OEM replacement this part is also compatible with Maytag, Jenn-Air, and some Kenmore models.

Comes with the metal shields

This dishrack wheel lets the dishwasher rack glide smoothly in and out. Replacing a worn or broken wheel restores easy rack movement and helps keep the rack aligned during loading and unloading.

• Provides rolling support for the dish rack inside the rail/track
• Helps keep the rack level and properly aligned
• Common symptoms include rack hard to slide, wobbling/sagging rack, or a cracked/missing wheel
• Can reduce scraping or clicking noises when moving the rack

• Disconnect power before servicing; remove the rack from the tracks as needed
• Release the old wheel from its axle/retainer; note its orientation
• Snap the new wheel onto the existing axle/retainer and ensure it spins freely
• Reinstall the rack and test for smooth operation

The Dishwasher Tine Clip is an OEM part for Whirlpool dishwashers. It is designed to secure the tines in the dishwasher rack, keeping them in place to properly hold dishes, glasses, and other items during the wash cycle. This clip ensures that the tines remain upright and stable, providing organized and effective loading of the dishwasher.

You should replace the dishwasher tine clip if it becomes damaged or lost. Causes of a bad tine clip can include wear and tear from regular use, breakage from heavy loads, or damage from the high temperatures and detergents used during the wash cycles. A compromised tine clip can lead to tines that are loose or misaligned, affecting the dishwasher's ability to hold items securely.

Symptoms of a bad dishwasher tine clip include:

• Tines that do not stay upright or move out of place
• Difficulty in properly loading items into the dishwasher rack
• Items tipping over or not being held securely during the wash cycle
• Visible damage or breakage of the clip

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This wheel mounting strip secures the rack rollers to the dishwasher rack, keeping the rack aligned and rolling smoothly in and out. Replacing a worn or broken strip restores proper rack support and slide action.

• Holds multiple rack wheels in position along the rack edge
• Helps prevent sagging, binding, or uneven rack movement
• Common fix for racks that derail, feel wobbly, or won't roll smoothly
• Durable molded piece designed for the rack's wheel row

• Disconnect power and water before servicing
• Remove the rack, then transfer wheels from the old strip to the new one
• Snap or fasten the strip to the rack as designed; verify wheel rotation
• Check rack travel on both rails before returning to service

The Dishrack Roller and Axle Assembly is an OEM part for Whirlpool dishwashers. This part facilitates the smooth movement and operation of the upper dishrack inside the dishwasher tub.

Causes of a bad Dishrack Roller and Axle Assembly may stem from wear and tear over time, damage from misuse or improper loading, or debris accumulation hindering the rollers' movement.

Symptoms of needing to replace the Dishrack Roller and Axle Assembly can include:

• Difficulty in sliding the dishrack in or out of the tub
• Excessive noise or grinding sounds when moving the dishrack
• The dishrack becoming stuck or not rolling properly on the track

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This water inlet valve regulates the flow of household water into the appliance. When the control energizes the solenoid, it opens to deliver the correct amount of water for filling and operation, restoring proper flow and performance.

• Controls on/off flow from the household water supply
• Opens when signaled to provide the correct amount of water for fill functions
• Helps maintain consistent water flow to the system
• Common failure symptoms: no water flow, slow fill, intermittent filling, or leaking at the valve body

• Disconnect power and turn off the water supply before servicing
• Place a towel to catch residual water and relieve line pressure
• Note tubing and wire locations before removal; transfer any brackets or clips as needed
• After installation, restore water and power, check for leaks, and purge air from the lines

Color: Grey. 4oz bottle with brush used for touching up damage to your dishracks. For blue use W10840471. For white use WP676453. For tips use 676458.

This dishwasher water deflector redirects spray back into the tub at the front edge, helping prevent splash-over and leaks during cycles. Replace a cracked, warped, or missing deflector to keep floors dry and wash performance consistent.

• Directs wash water away from the door opening and front corners
• Helps reduce leaks and puddles at the bottom front of the dishwasher
• Restores proper containment when the original deflector is deformed, loose, or missing
• Common symptoms include water on the floor at the front, drips during cycles, or visible damage to the deflector

• Disconnect power and turn off the water supply before servicing
• Open the door to access the front/tub area; remove the old deflector
• Clean the mating area and seat the new deflector fully and evenly
• Run a short test cycle and check for leaks

This float controls your dishwasher's water level. As the tub fills, it rises to signal the float switch to shut off incoming water, helping prevent overfilling and leaks.

• Lifts with the water to actuate the float switch and stop filling
• Helps protect against overfilling and door leaks
• Replace if the float is cracked, deformed, waterlogged, or sticks in its well
• Symptoms can include: won't fill or stops filling early; overfilling or leaks at the door

• Disconnect power and shut off the water supply before servicing
• Remove the lower rack and locate the float in the tub floor
• Lift the old float straight up; clear any debris; seat the new float and free up-and-down movement
• Restore power and run a fill test to proper operation and check for leaks

The Fold Away Tine Pivot is an OEM part for Whirlpool dishwashers. This component allows the fold-away tines in the dishwasher rack to pivot, enabling flexible loading configurations to accommodate different types and sizes of dishes.

Causes of a bad fold away tine pivot can include regular wear and tear, repeated adjustments leading to stress fractures, or physical damage from heavy dishes or improper handling.

Symptoms of a bad fold away tine pivot include:

• Tines not staying in place or collapsing unexpectedly
• Difficulty adjusting the tines
• The pivot appearing cracked or broken
• Reduced stability of dishes during the wash cycle

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This heater warms the wash water inside the tub during selected cycles. Replacing a failed element restores proper water temperatures, supporting cleaning performance and preventing extended run times or incomplete cycles. What it does:

• Heats water in the washer tub during hot/sanitize/temperature-controlled cycles
• Helps maintain target temperature for effective cleaning and stain removal
• Common symptoms include water not heating, cycles taking unusually long, or cycles stopping early
• Accompany control errors related to water temperature or the heater circuit

• 1 heater

• Disconnect power and shut off water supplies before servicing
• Access is typically from the rear or bottom; be prepared for residual water when removing the old element
• Clean sealing surfaces and seat the element fully; tighten fasteners evenly to prevent leaks
• After installation, run a hot cycle to check for leaks and heating

This small clip secures the guard/shield on the dispenser assembly. Replacing a cracked or missing clip keeps the guard firmly attached and aligned so the dispenser operates properly without interference, noise, or premature product loss. What it does:

• Fastens the dispenser guard to its mounting point on the dispenser assembly
• Keeps the guard aligned to prevent interference with dispenser door/flow
• Restores a secure fit if the original clip is cracked, deformed, or missing
• Common symptoms: loose or missing guard, rattling, incomplete dispensing or residue left after a cycle

• 1 dispenser guard clip

• Disconnect power to the appliance; turn off water supply if applicable
• Open access, support the guard, and release the worn clip from its tabs
• Snap the new clip fully into place, ensuring it engages all locking points
• Ensure the guard is secure and that the dispenser door/flow path is unobstructed before use

This cap secures the dishwasher wash arm to its support, helping keep the arm properly positioned so water jets can spin and spray effectively for consistent cleaning performance.

• Holds the wash arm in place on its hub/support
• Can help address a loose, wobbly, or detached wash arm
• Replacing a damaged or missing cap can restore stable arm rotation

• Disconnect power and turn off water before service
• Remove the lower rack for access; lift off the wash arm
• Unscrew/press off the old cap; seat and secure the new cap
• Ensure the wash arm spins freely by hand before reassembly

Color: Black