Jenn-Air Dispenser Parts

This refrigerator ice guide channels cubes and crushed ice along the intended path so they land in your bin or glass. When the guide is damaged or missing, ice can scatter, jam, or miss the dispenser opening. What it does

• Guides ice from the ice maker/bucket into the bin and through the dispenser chute
• Helps keep ice flowing smoothly and reduces spills at the opening
• Restores proper aim for cubed and crushed ice
• Typical symptoms: ice spraying or missing the glass, frequent jams, or visible damage to the guide

• 1 ice guide

• Disconnect power to the refrigerator before servicing
• Remove the ice bin and access the guide per your model's design
• Transfer and reuse existing mounting screws or clips, if applicable
• Verify alignment, then test both cubed and crushed dispensing

Color: White. Size: 3 3/8 inches in diameter. This is the door chute located in the freezer door on your refrigerator.

This ice door motor drives the dispenser flap that opens for ice dispensing and closes to seal the chute. Replacing a weak or failed motor restores smooth door movement and helps prevent warm air and moisture from entering the freezer. What it does:

• Actuates the ice chute door during dispensing and returns it closed for a proper seal
• Helps reduce frost, condensation, and ice clumping around the dispenser
• Can address ice not dispensing due to the door not opening/closing
• May resolve clicking or grinding noises from the dispenser area

• Unplug the refrigerator before servicing; wear cut-resistant gloves
• Remove dispenser trim/control panel to access the ice door assembly; handle wiring carefully
• Note linkage and wire orientation before removal to ensure proper reassembly
• After installation, test the dispenser to verify the door opens/closes and seals the chute

Color: black. It measures about 10 inches wide by 4 inches deep.

This dispenser facade replaces the outer trim pieces around your refrigerator's ice and water dispenser, restoring appearance and proper fit for smooth operation and sealing. It's a direct-fit cosmetic and protective assembly. What it does:

• Covers and protects the dispenser opening and controls from damage and debris
• Provides a finished look and helps direct water/ice into the cup
• Restores proper alignment when cracked, warped, or broken facade causes interference
• Helps prevent drafts and minor water splash at the dispenser area

• Disconnect power and shut off water to the appliance before servicing
• Many installations require removing the dispenser bezel and releasing snap-clips or screws; save hardware for reinstallation
• Handle plastic trim carefully to avoid scratches; use a soft pad when setting parts down

This cover is a factory replacement access panel that protects internal components and restores the appliance's finished appearance. It keeps wiring and controls shielded from dust and accidental contact for safer, longer-lasting operation. What it does:

• Shields internal wiring, controls, and components from dust, debris and accidental contact
• Keeps small parts and fasteners secured inside the appliance cabinet
• Restores the appliance's finished exterior where the original cover was damaged or missing
• Helps maintain proper airflow routing and component spacing when installed correctly

• Disconnect power to the appliance before beginning any service to avoid shock or injury.
• Verify the cover orientation and fastener locations before securing; use OEM screws where specified.
• Handle with care to avoid scratching or bending the cover; ensure tabs snap fully into place.
• Inspect for damage and secure any loose parts before installing the cover.

A small replacement retainer clip used to secure exterior trim and interior panels on compatible Whirlpool appliances. Restores proper panel fit and prevents rattling or loose trim for a cleaner, safer operation. What it does

• Secures trim, panels or components in place to maintain proper alignment
• Helps stop rattling, vibration noise and loose-fitting parts
• Keeps seals and covers positioned so doors and panels close correctly
• Simple, single-purpose hardware used where a clip-style fastener is required

• One retainer clip as pictured

• Disconnect power (and water if applicable) before starting any repair
• Remove the surrounding trim or panel to access the retainer; small trim tools may help
• Fasten clip into the OEM mounting hole until it snaps or seats firmly
• Keep removed screws and small parts organized to avoid lost hardware

The Icemaker Fill Cup is an OEM part for Whirlpool bottom-mount and side-by-side refrigerators. Located inside the icemaker assembly, the fill cup sensor works to automatically detect when an ice scoop or bucket is in place below the icemaker chute. It signals the icemaker to drop ice cubes into the receptacle below.

Causes of a bad fill cup sensor can include mineral or dirt build-up inhibiting sensor response, moisture damage to its electronic functioning, or physical damage to the sensor head.

Symptoms of a bad fill cup sensor include:

• Ice failing to dispense or drop when a container is in place
• Ice clumping in the chute instead of dispensing properly  
• The icemaker continuing to run even with ice present below
• Inability to sense when ice is removed from the bucket

This OEM Whirlpool replacement fill cup sensor is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and some Kenmore bottom-mount and side-by-side refrigerators. 

Color: Black

Color: Black