Jenn-Air Housing Or Cover

This ice enclosure is the molded housing for the refrigerator's ice compartment. It supports and protects the ice dispensing components and guides ice into the chute or bin, helping maintain proper alignment and smooth dispensing. What it does:

• Provides structural support for the ice bucket/auger and related dispenser components
• Helps guide ice from the compartment into the chute/bin to reduce spills and jams
• Aids in maintaining alignment and a consistent cold zone around the ice area
• Typical symptoms of failure: cracked/broken housing, ice bin won't seat securely, ice jams or intermittent dispensing, frost/ice buildup in the ice compartment

• One ice enclosure

• Disconnect power; remove the ice bin before service
• Note screw locations; detach the old enclosure and any connected clips or wiring
• Transfer any brackets or hardware from the original enclosure; reuse existing fasteners
• Mount the new enclosure without overtightening; restore power and verify normal dispensing

This ice enclosure is the molded housing for the refrigerator's ice path. It supports and aligns related components so ice moves properly and helps keep warm air out to reduce frost and moisture around the ice area.

• Provides a rigid mounting point for ice-path components to keep alignment and flow
• Helps maintain an air barrier to minimize frost, sweating, and ice clumping
• Replace if the original housing is cracked, warped, or broken
• Common symptoms include frost or condensation near the ice opening, ice clumps, or poor/jammed ice dispensing

• Disconnect power and shut off water before servicing
• Access the ice area (door or interior access varies by model); retain screws and clips for re-use
• Transfer any guides, seals, or switches from the original enclosure to the new part in the same orientation
• Reassemble, restore power, and check for smooth operation and a good seal

This OEM part is a griddle cover made for stoves. A griddle cover is a metal piece that can be placed over the stove's burners to be used as a cooking surface. If a griddle cover becomes damaged due to excessive use, it can become ineffective and need to be replaced. Luckily replacing a griddle cover is a very simple process.To replace the griddle cover, make sure the stove is unplugged. Being by lifting the old cover out of its place by pushing it forward and lifting upward to release it from its attachment on the stove. Once removed set it off to the side. Next, proceed to take the new cover and place it back where the old one was while making sure it locks into its attachment. Once secured, turn the power back on to the appliance.This genuine replacement part is sold individually and is compatible with Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Sears/Kenmore brand stoves.

This housing is the factory replacement outer cabinet that secures and protects internal components while restoring proper fit and appearance. It's a direct-fit body panel that helps keep parts aligned and shields wiring and controls from damage. What it does:

• Replaces cracked, warped, or damaged outer housing that affects cabinet fit or appearance
• Supports and secures internal components and mounting points for panels and controls
• Protects wiring, switches, and electronics from exposure, debris, and accidental contact
• Helps reduce rattles or misalignment caused by a broken or loose housing

• Disconnect power (and water if applicable) before starting any repair
• Handle edges carefully — metal/plastic edges can be sharp
• Basic hand tools required; alignment and fastener locations must match the original housing

This evaporator fan shroud directs airflow from the evaporator fan to the refrigerator's cooling coils, improving cold-air circulation and helping maintain even temperatures in the fresh and freezer compartments. What it does:

• Channels airflow from the evaporator fan to the evaporator coils for efficient heat exchange
• Protects the fan motor and blades from contact with ice and debris
• Helps reduce uneven cooling or warm spots caused by disrupted airflow
• Fits into the evaporator compartment and mates with the fan assembly

• Intended for use in the evaporator compartment;
• Disconnect power to the appliance before accessing internal components to avoid shock or injury
• Handle the shroud gently to avoid damaging tabs or mounting points during removal/installation
• Reassemble panels and test cooling operation after installation