Jenn-Air Dryer Parts

• Won't start

Through 15 years of vibration, the Cycling Thermostat evidently had degraded to the point where one electrical connection or more came loose and caused a short. There is also a possibility that the Bakelite section of the Dryer Cycling Thermostat body separated from the metal base, simultaneously exposing all four connections to a short. The thermostat literally exploded into chunks and dust. There was a heavy arcing and then, thankfully, the thermal fuse blew and shut down power to the short... Read more

Removed LP Orifice and LP Gas limiter. Orifice was easy, however the gas limiter was the tricky one because I had no instructions to what went where. I could not find anything online as to how to convert from LP to Natural Gas, but you could find several things as to how to convert from Natural to LP. I ended up finding the Dryer schematic on line for the Whirlpool Duet natural gas dryer and was able to figure out what sequence the Spring, regulator and limiter went in. The order I just... Read more

• Door won't close

Took off front cover of drier, removed old part and just snapped in new part. Read more

• No heat or not enough heat

The root cause was the front glides. They were virtually gone, and the drum was on metal to metal. So I replaced them with a front glide kit. I also replaced the belt, rear rollers, and lint screen. I am happy to say all the parts fit perfectly, and I couldn't find a better price anywhere else. I will definitely keep you on file for the next time I need appliance parts! Thank you! Sincerely, pw Read more

• Door won't close
• Shuts off too soon
• Doesn't shut off
• Takes too long to dry

Ordered a new clip and installed it. Easy to do. Unplugged the dryer. Removed the front. It is only held on by two screws. Removed wires to the door switch. removed the female end (it had the broken male piece in it. Inserted the new female part in the front, clipped in the male part into the door and reconnected the door switch wires, screwed the front back on. Job done. Total time was less than 10 minutes. Works like new. Read more

Seal and adhesive. Read more

I watched the video at your website. I unplugged the electric first. When I opened up the machine up, It was loaded with lint.I found the source was a hole in the vent tube outside the machine. I fixed that first . The lint had been sucked back into the machine. The first half hour was spent vacuuming out all the lint and then I could proceeded with the motor change. I followed the video exactly. I removed the screws at the two front corners, after lifting the top and controls and tying it... Read more

• Won't start
• No heat or not enough heat

Did some dryer repair research (dryer not heating) on the internet. Bought an ohm meter, opened up the dryer and tested the cut-off-T, high limit thermostat, dryer igniter, flame sensor, cycling thermostat for continuity. The igniter was bad, the other parts tested ok. Went online to AppliancePartsPros.com searched for a new igniter for my specific dryer model, found the right replacement igniter and watched the video on how to replace the igniter. Because my dryer is old (15+ years) and I... Read more

Ordered the freezer door switch and the light. Replaced the freezer door switch and the light and everything is back to normal. Replaced both in less than 15 min with no problems. Read more

I took the dryer apart.....first had to clean out all the lint here and there. Took the drum out, inspected the belt and back support wheels. They seemed to be fine. In the front the drum turns on two supports that have a Teflon glide. Those two glides had been worn off with their pad so metal was rubbing against metal. Went online to appliancepartspros.com and looked up on the schematic what parts I needed. I also had called around locally and the same parts cost twice as much....so I... Read more

• Light not working

I saw your video on you tube and it seems very easy to do it my self, so I ordered the parts and I did it my self. It was very easy. Thank you for sharing with us on how to did it. One more thing, the parts arrived on the time they said it would come. Read more

• Element will not heat

I lucked out my nephew was here to deer hunt and he helped me. I do believe I could have done it on my own but was more confident with his help. I will say the videos did help. Read more

I went on line and purchased all of the possible parts that could be worn out. I spent less than the service guy wanted to show up...The online videos were spot on. Two hours and it works like new! One of the best values on the Internet! Read more

When I pulled out the dryer from the wall, I could see dust/lint had accumulated everywhere and the vent system was compromised. I vacuumed up the dust/lint accumulation outside and then inside the vent system. I then opened the lower cabinet to clean and check its condition. I removed the water steamer bottle and its sub-assembly and then the drum. After cleaning and inspecting components — both visually and with a multi-meter I determined the problem was the appliance doing what it was... Read more

Went on internet, found a great site and learned that the cold water hose filter was very much clogged at the machine intake. Cleaned it and voila. Ordered an extra filter from Appliance Pros.com and literally was amazed that it arrive within 2 days of my internet order. Great efficiency and customer service….great experience. Will definitely use them in the future….thank you! Read more

• Shakes and moves

Took off the old parts and replaced with the new parts Read more