Jenn-Air Wall Oven Heating Element

• Element will not heat

I lucked out my nephew was here to deer hunt and he helped me. I do believe I could have done it on my own but was more confident with his help. I will say the videos did help. Read more

It was a simple process to enter the model number of our glass cook top stove; learn the part number required and order. It arrived in 2-days -- least expensive shipping method. The cooktop was removed with a Phillips-head screwdriver by 4 small sheet metal screws on the right and left side of the oven. The oven's power to the cooktop was easily disconnected via two "clips" and one ground. Would have cost way more with an appliance repair shop and it's an easy do-it-yourself repair. Read more

Little procrastination paid off. With only 50% capability I knew it is time to call the appliancepartspros. They shipped me parts within 3 days. It was practical to fix both at the time. All I needed was to disconnect power at range breaker box, grab a screwdriver to lift top open, a 16 inch or so piece of old 2×4 wood to keep the top top of stove lifted, so I could access heating elements from underneath. Then I took my black sharpie And marked location of mounting screws and... Read more

• Little to no heat when baking

It took 10 minutes and a screwdriver, remember to turn off power to the oven at the fuse box. By the way, I ordered the part at 1:30pm and received it at 12:30pm the next day using normal shipping, not bad. Read more

I purchased the replacement element. The element was a direct replacement. The entire replacement took 20 minutes, 15 minutes of which was to clean the range before putting it back. Read more

I ordered a replacement burner from AppliancePartsPros.com and replaced it using a u-tube video to find out how to do it. I took pictures of the wiring before I took it apart and then removed the burner element from the glass tom, but I left all the wires attached. I screwed the new element to the glass top and then one by one I unhooked each wire from the broken element and then hooked them each back onto the corresponding place on the new element. I used the digital pictures I took of the... Read more

• Little to no heat when broiling

I went on line and found several appliance web sites promising to be able to get the parts to fix it. One website actually showed a video of how to fix it. It was a good video which showed everything involved and then easily showed me the parts list of the elements involved and how to fix it. I went further and actually ordered the element at about 1 or 2 AM. Read more

• Little to no heat when baking

I purchased a new element from Appliance Parts Pros online and received it a short time later. I was able to determine the correct size and element as a result of the picture and graph background. Very Helpful!!! The stove is over thirty years old and so it took some time for my friend to get the old screws out. Otherwise, installation was straightforward. Read more

• Element will not heat

Not really a repair, just needed to update some parts that were worn out. Drip pans were perfect and I am so glad to have found them on this location. Read more

Easy. Pulled the two screws that hold the top in place. Then lift the top and slide it forward 4 inches. Reach in and disconnect the two wiring harnesses (Squeeze the sides to release). Lift the entire top off and place it upside down on the table. Remove the four screws that hold the metal panel to the top. Flip this panel upside down. From under the panel and release the three clips that hold the element in place. ***YOU NEED TO SAVE THESE CLIPS**** they do not come with the new... Read more

It's one of the easiest jobs in the world. It take longer to unwrap the parts than to install them. Looks great...works great. Easy, Done. Read more

First, I just unscrewed all nuts that are holding the frame and all surface elements. Once all parts, surface elements, control switches, are loose from the original glass, I just moved all parts to the new glass. Due to the weight of the glass, all actions have to be done carefully as I broken one corner of the glass couple of years ago when I replaced one of the control switch. Read more

Very easy fix. Remove oven door by just opening it slightly and pulling up. (an easy way to clean it too). Then, with a phillips screw driver, remove two screws holding the damaged element in place. Slowly pull the element toward the front a couple inched to expose the wires. Disconnect the wires (no tools needed), remove the old element and replace it with the new. Reverse the past few steps and re-attach the wires and screw. Simple as that. I also chose to replace the Broiler Element as a... Read more