Kenmore / Sears Burner & Related Parts

This oven bake burner is designed for Direct Spark Ignition (DSI) ranges. It channels gas from the bake orifice and distributes an even flame under the oven floor for consistent baking performance and reliable light-off during the bake cycle.

• Distributes gas through burner ports to create an even bake flame
• Works with the DSI spark electrode to ignite the bake flame
• Can address uneven or weak flame patterns and delayed ignition in bake

• Disconnect power and shut off gas; allow the oven to cool completely
• Remove the oven bottom and flame spreader to access the burner
• Transfer any reusable mounting hardware or shields from the original burner
• After reassembly, restore gas/power and leak-test any disturbed gas connections per local code

This genuine OEM part is a cooktop grill burner. The grill burner is the component part that allows the gas flame to spark so that the stove can perform its job of cooking and heating. If the stove burners are no longer producing a flame or not turning on at all, it might be time to replace the grill burner. Luckily this is a relatively simple repair.To start, make sure that all power to the stove has been turned off by either unplugging the appliance or shutting off the circuit breaker. Close the shut off valve on the propane gas tank. Remove the cooking grate and the flame tamer from the top of the damaged burner. Pull the cotter pin out of the back of the burner. Remove the burner mounting screws. Pull the burner back then up to remove it from the manifold and remove the burner. Place the new burner into the manifold and fasten the mounting screws. Reinstall the cotter pin and flame tamer and restore the gas and power back to the appliance.This replacement part is sold individually and is compatible with Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Sears/Kenmore brand stoves.

6,000 BTU. Color: Coal matte black. Measures about 2 inches in diameter.

This gas surface burner head sits on the burner base and channels gas through precision ports for quick ignition and an even flame. Replacing a worn or clogged head helps restore reliable lighting and consistent heat.

• Distributes gas from the burner base to the flame ports for even flame patterns
• Interfaces with the spark electrode to enable ignition
• Helps maintain proper flame shape and heat output
• Common symptoms include burner won't light, weak/uneven or yellow flames, delayed ignition, or continuous clicking

• Disconnect power and shut off the gas supply before servicing
• Remove grate and burner cap; lift the old burner head off the base
• Clean the burner base and electrode area; align the new head with locator pins and the electrode opening, then seat fully
• Reinstall cap and grate; restore gas/power and test ignition and flame

This Orifice Spud precisely meters gas to a burner so you get a steady, properly sized flame. Replace a damaged, clogged, or incorrect spud to restore reliable ignition, clean flame color, and consistent heating.

• Threads into the burner's orifice holder/valve to control gas flow through a calibrated opening
• Helps maintain correct flame height and color for safe, efficient cooking
• Typical symptoms include irregular or yellow flames, weak or no flame, popping, or delayed ignition
• A clogged or worn spud can make simmer control difficult and lengthen cook times

• Shut off gas supply and power; allow the appliance to cool before service
• Remove grate, cap, and burner head (as applicable) to access the orifice; use the proper wrench or nut driver and avoid overtightening brass parts
• After reassembly, restore gas and check for leaks with soapy water; verify a steady blue flame and adjust air shutters only if directed by the manufacturer

This range burner base is a replacement part that is used for gas stovetops and ranges. This burner base directs gas to the burner head. It also holds the orifice. If this part of the range is broken or not working properly, it will not direct the gas where it needs to go. It could make it more difficult to head up the burner, and it could prove to be dangerous.While the metal pieces are durable and made to last, they may still need to be replaced. They could become dirty or corroded, or they could suffer damage when the range is moved. When replacing the burner base, owners will first want to shut off the gas supply to the stove and ensure the burner is completely cool before starting. When repairing, owners should also wear gloves to protect their hands.The burner base is compatible with many models of ranges from Whirlpool, Roper, Crosley, Estate, and Inglis. This is a genuine OEM part that has been sourced from the manufacturer. It is sold individually.

The Regulator is an OEM part for Frigidaire cooktops. It is responsible for regulating the flow and pressure of gas entering the appliance, ensuring safe and efficient operation.

A bad regulator can be caused by faulty internal components, wear and tear over time, or damage due to improper handling. Signs of a faulty regulator include uneven heating, weak flame, or gas leaks.

Symptoms of a bad regulator can include:

• Uneven heating of burners or oven 
• Weak or inconsistent flame 
• Gas leaks around the regulator 

This Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

This governor assembly is the mechanical control that stabilizes and regulates motion within the appliance's drive mechanism. Replacing a worn governor restores smooth, consistent operation and helps prevent erratic movement that can strain connected components. What it does:

• Regulates and limits the speed/rotation of the linked drive for stable, predictable movement
• Helps synchronize gears or shafts so the mechanism operates smoothly
• Common symptoms: intermittent or no movement, jerky/erratic motion, clicking or grinding noises
• Visible wear, cracks, or a loose/broken hub on the original governor

• 1 governor assembly

• Disconnect power before servicing; allow moving parts to come to a complete stop
• Note the original orientation; take photos to aid reassembly
• Transfer any reusable brackets, clips, or spacers from the original if required
• After installation, rotate the mechanism by hand to verify free movement before restoring power

This small cap snaps into the center of a control knob. It refreshes the appearance and helps keep moisture and debris out of the knob interior so the control stays protected and easy to use. What it does:

• Provides a finished cover for the center of a control knob
• Helps protect the knob interior from spills and debris
• Restores a clean look when the original cap is missing or damaged
• Addresses a loose or rattling knob insert

• 1 control knob cap

• Disconnect power to the appliance for safety before working near controls
• Pull the knob straight off the control shaft; remove any remnants of the old cap
• Align tabs and snap the new cap into the knob firmly
• Reinstall the knob on the shaft and verify smooth operation

Color: Black

The Surface Burner Cap is an OEM replacement part designed for Whirlpool gas ranges. This component covers and protects the burner head, helping to evenly distribute the flame for consistent cooking heat. It also shields the burner from debris and prevents clogs that could impede performance.

Over time, burner caps can suffer from regular wear and tear, high heat exposure, or damage from accidental impact. 

Color: Black

Symptoms of a faulty surface burner cap include:

• Uneven or inconsistent flame pattern
• Difficulty igniting the burner
• Visible cracks, warping, or discoloration
• Poor fitting, leading to debris buildup around the burner head

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Protective cap that covers a terminal or post on select Frigidaire appliances, helping keep dirt, moisture and accidental contact away from electrical connections for safer operation and longer component life. What it does:

• Covers and protects electrical terminals/posts from dust, moisture and corrosion
• Helps reduce the risk of shorting from accidental contact with nearby metal parts
• Maintains a secure, insulated connection where a terminal or post is exposed
• Useful when replacing damaged or missing covers to restore normal protection

• Disconnect power to the appliance before inspecting or replacing electrical components
• Remove the old or damaged cap and press the replacement firmly over the terminal/post until fully seated
• Inspect surrounding wiring and terminals for corrosion or damage; replace if needed

This LP gas conversion label identifies that the appliance has been converted for use with liquid propane. Applying it near the gas valve/regulator clearly communicates fuel type for safe service, troubleshooting, and future installation decisions.

• Marks a converted unit as LP fuel to prevent misdiagnosis or incorrect hookups
• Provides quick visual identification for technicians and inspectors
• Replaces a missing, damaged, or illegible conversion label
• Use when a conversion has been completed and the original label is not present

• Apply only after completing the correct LP conversion procedure for your specific model
• Clean and dry the mounting surface; place the label where specified (typically near the gas valve/regulator or rating plate)
• Do not cover existing safety or rating labels; press firmly to ensure full adhesion
• Leak-check all fittings before returning the appliance to service

This circuit board mounting bracket secures an electronic board or module inside the appliance. It prevents movement, vibration damage, and wiring interference so the component stays correctly positioned for reliable operation.

• Mounts and supports a small circuit board or module within the chassis
• Maintains proper spacing and alignment to reduce chafing or electrical short risks
• Replace if bent, cracked, or missing tabs, or if it no longer holds the board securely
• Common signs include a loose/rattling board, visible bracket damage, or intermittent operation when the panel is bumped

• Disconnect power at the breaker; shut off gas supply if applicable
• Remove the necessary access panel(s) to reach the board and bracket; note orientation and wiring
• Transfer the board/module to the new bracket and reinstall using existing hardware
• Watch for sharp metal edges; route wires to avoid pinching and verify clearances before restoring power

This surface burner cap sits atop the gas burner head to distribute flame evenly and protect the burner from spills, helping restore steady flames and reliable ignition when the original cap is worn, warped, or missing.

• Distributes flame for more even heating across cookware
• Shields the burner head from boil-overs and debris
• Supports proper ignition when correctly seated and level
• Common signs it's needed: missing cap, chips/cracks, warping, uneven or yellow flames

• Allow the cooktop to cool completely; shut off gas/power if performing additional service
• Remove the grate, lift off the old cap, and clean the burner head surface
• Center the new cap on the burner head so it sits flat and does not rock
• Test the burner; if ignition is delayed or flames are uneven, reseat the cap

Restore strong, even flame on your large burner. This sealed burner head replaces the 12K position on gas ranges/cooktops, helping recover reliable lighting and consistent heat when the original head is clogged, corroded, or damaged.

• Directs gas through calibrated ports to deliver a stable, even flame on the 12K burner position
• Helps address: burner won't light or lights intermittently; weak, uneven, or yellow flames; flame lifting or sputtering
• Replace when ports are clogged beyond cleaning, or the head is warped, cracked, or corroded
• Seats over the orifice and spark igniter in sealed-burner designs

• Disconnect power and shut off gas; allow the surface to cool completely
• Remove grate and cap; lift off or unthread the old head, retaining any mounting screw
• Clean the mating surface; align the new head over the orifice and igniter so it sits flat; if screw-retained, tighten snugly only
• Reinstall cap and grate; restore gas/power and confirm proper ignition and flame