Kenmore / Sears Dryer Cap Or Cover

This replacement cover restores the appliance's finished appearance and protects internal components from dust and debris. It's a direct-fit exterior trim piece designed to replace a cracked, broken, or missing cover. What it does:

• Protects internal components and wiring from debris and accidental contact
• Restores the appliance's cosmetic appearance and helps maintain sealing
• Helps reduce dust buildup in the covered area
• Replaces damaged or missing trim that can expose sharp edges or hardware

• Disconnect power (unplug or switch off circuit breaker) before beginning work
• Basic hand tools may be required; follow for panel removal/replacement
• Handle carefully to avoid scratching the finish and watch for sharp edges
• Replace with manufacturer-recommended fasteners

This lint cover is the exterior housing that holds and protects the dryer's lint screen, helping keep lint and debris contained for safer, more efficient drying. It's a direct-replacement style part designed to restore proper lint capture. What it does:

• Holds the dryer lint screen in place so lint is collected instead of entering the cabinet
• Prevents lint and debris from falling into the blower and exhaust path
• Helps maintain proper airflow through the lint screen area
• Commonly replaced when cracked, warped, or when the screen no longer seats securely

• One lint cover (housing) as shown

• Disconnect power to the dryer before attempting service
• Access may require removing the dryer's top or front panel; keep fasteners organized
• Inspect the lint screen and surrounding seals while replacing the cover

This dryer blower cover encloses the blower wheel and seals the housing so air moves efficiently from the lint screen to the exhaust. Replacing a cracked or missing cover restores airflow for consistent drying performance and helps keep lint contained.

• Covers the blower wheel and seals the blower housing
• Directs air from the lint screen through the exhaust duct
• Helps maintain proper airflow and drying performance
• Damage or gaps may cause reduced airflow, longer dry times, vibration/noise, or lint leaking inside the cabinet

• Unplug dryer and let components cool before servicing
• Access the blower housing; front or rear access varies by model
• Clean lint from housing and ducts; inspect the blower wheel and any gasket/seal
• Seat cover squarely and tighten fasteners evenly; verify the blower turns freely and no air leaks are present

This small plug seals and finishes an unused factory or service hole on the appliance cabinet or liner. It restores a clean, finished appearance and helps keep dust and splashes out of the opening. What it does

• Closes an open hole on the cabinet/liner or panel
• Helps reduce entry of debris and incidental moisture into the opening
• Maintains a neat, finished look
• Replace if the original plug is missing, cracked, or won't stay seated

• 1 plug

• Disconnect power before servicing; shut off water supply if working near water lines
• Identify the correct opening per your model's parts diagram
• Remove any remnants of the old plug; clean the area
• Align and press the plug fully into the hole until it sits flush—do not force or deform the panel

The Filter Housing is an OEM part for Whirlpool dryers. As part of the dryer ventilation system, the filter housing holds the lint filter in place, trapping lint and debris before it exits through the vent. It helps prevent blockages in the exhaust vent and surrounding area.

Causes of a bad filter housing can include cracks, breaks or defects in the plastic material over time due to normal use and heat exposure inside the dryer. Increased wear and tear from extended use can also cause damage.

Symptoms of a bad filter housing include:

• Excessive lint building up inside the dryer
• Reduced air flow and inefficient drying times
• Strange sounds like vibrations or rattling coming from the vent area
• Lint escaping from gaps in the filter housing

This genuine OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This snap-in hole cap covers and seals an unused opening on the appliance cabinet or control panel to restore a finished look and help keep out moisture and debris. Simple cosmetic repair that prevents dirt buildup and accidental contact with interior components. What it does:

• Covers an exposed hole or access opening for a neat, finished appearance
• Helps keep out dust, crumbs and light moisture from entering the cabinet
• Reduces risk of accidental contact with interior parts through an open hole
• Restores factory look after removing a screw, plug, or accessory

• One snap-in hole cap

• Snap into the hole from the exterior until fully seated; minimal force required
• Use a plastic trim tool or small flat blade carefully if needed to pry out old cap
• Disconnect power or follow appliance-specific safety precautions before accessing internal areas
• Replace if cracked or deformed

The Lint Screen Housing is an OEM replacement part for LG dryers. It serves as the enclosure that holds the lint screen or filter, which plays a crucial role in capturing lint and preventing it from accumulating inside the dryer. This housing  measures approximately 17 in x 12 in,

Symptoms of needing to replace the lint screen housing include:

• Difficulty in removing or inserting the lint screen
• Visible cracks, warping, or damage to the existing housing
•  Lint buildup or leakage around the housing area
• The housing becoming loose or not securely holding the lint screen in place

Causes of a faulty lint screen housing can include normal wear and tear over time, exposure to excessive heat or lint buildup, or physical damage due to impact or mishandling.

This OEM LG part is also compatible with Sears/Kenmore dryer models, ensuring a perfect fit and reliable lint filtration for your specific appliance. NOTE: Due to a manufacturing change, this filter housing may be different from your original. If you have any issues installing your filter, you may need to order new filter part# ADQ56656403 and new guide part# MEA49050001 for a proper fit. When ordering [AP5071745} you will need to order filter ADQ56656403.

This cabinet hole cap plugs unused hinge or screw openings on the dryer cabinet. It restores a clean, finished look and helps keep lint and moisture out after a door reversal or service. What it does:

• Covers open hinge/screw holes on the dryer cabinet
• Helps block lint, dust, and moisture from entering through unused openings
• Restores a finished appearance; helps prevent snags around exposed holes
• Commonly replaced when a cap is missing, cracked, or loose

• 1 cabinet hole cap

• Disconnect power before working near the cabinet
• Remove any damaged cap and clean the opening
• Press the new cap into the hole until fully seated and flush
• Wear gloves; cabinet edges and holes can be sharp

This manifold cover protects the appliance manifold assembly by shielding valves and fittings from dust, debris, and accidental contact. It restores a secure, finished appearance and helps keep manifold components functioning reliably. What it does:

• Shields manifold valves, fittings and connections from dust, food particles and spills
• Helps prevent accidental snagging or contact with manifold components during use or maintenance
• Restores a damaged, cracked or missing cover to maintain a finished appearance
• Can reduce intrusion of debris that complicates service or repairs

• Disconnect power and shut off gas supply before starting work
• Replace only with the correct OEM part and align over manifold before fastening
• Use appropriate fasteners; do not overtighten to avoid cracking the cover

This adhesive label replaces a worn, damaged, or missing information label on your appliance so model, serial, and warning details remain readable and the unit stays compliant with safety and service needs. What it does

• Restores legible model/serial/rating and safety information used for service and identification
• Replaces faded or peeled factory-applied adhesive labels
• Helps ensure important operating and safety instructions remain visible
• Improves appearance by covering damaged or discolored label areas

• Clean and dry the mounting surface thoroughly before applying the label
• Peel backing and press firmly, smoothing out air pockets for full adhesion
• Avoid stretching the label during installation; align carefully before contact
• If the label is near electrical components, disconnect power before working in the area