We use cookies and similar tools for site analytics and advertising. By using our site, you agree to this. See our Privacy Policy for details. Do Not Sell or Share My Personal Information
Need Help?
Call
Burner won't turn off or element light stays on? This range burner control switch regulates temperature and power. Moderate DIY repair, 30-60 minutes.
I went on your website found the parts needed to make the repairs. I watched the short video on installation. The parts arrived just a few days after I placed the order. I finished the repair in less than an hour and had to wait a few minutes to test the switch since the power was off and on due to a wind storm. Simple easy to do repair and I saved $90.00 on service fee for a tech to do the repair. Read more
Most orders arrive by Tuesday, November 24
Seals the light lens to the oven cavity, blocking heat, steam, and grease from the bulb housing. Replace if cracked, brittle, or missing. Confirm fit.
Troubleshot the oven by checking the broiler which worked good (same fuel valve). After reading the some tips about troubleshooting the Glow Ignitor I could see the broiler ignitor got white hot and the oven ignitor only got bright orange (orange to red causes intermittent ignition or mini explosions). Watched the how to video and it was good information. You should be observant about which openings in the back of the oven as to where the two wires are coming out of. My oven is over 12 years... Read more
This surface burner ignitor/orifice assembly directs gas through a calibrated orifice and provides the spark to ignite it. Replacing a worn or damaged assembly restores consistent lighting and an even flame on the affected rangetop burner.
I replaced the Ignitor/Orifice Tube assembly. Read more
The Surface Element is an OEM replacement part for Frigidaire electric ranges, designed to provide efficient and even heating for cooking on the stovetop. This component is a radiant surface element commonly seen on glass and ceramic cooktops. 8 inch, 2200 watt
Causes of a faulty Surface Element can be due to overuse causing burnout, physical damage like cracks from heavy cookware, electrical issues such as faulty wiring, and corrosion disrupting heating.
Symptoms of a bad Surface Element include:
This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.
Changed element Read more
The Control Switch is an OEM part for Frigidaire ranges. This part regulates the heat output of the range's burners. By turning the control knob, users can adjust the temperature to their desired level, ensuring precise cooking results.
Causes of a bad control switch can include electrical malfunctions, wear and tear from frequent use, or damage due to overheating.
Symptoms of a bad Control Switch include:
I changed out the oven temp probe located inside the oven, and I also changed out the temperature control which is located behind the oven temperature control knob. The whole process was simple, but it took a little bit of time since we repaired it ourselves and had to located these parts inside the oven. Read more
The Convection Fan is an OEM part for Whirlpool wall ovens and ranges. It circulates hot air inside the oven cavity, facilitating even heat distribution during the cooking and baking cycles. The convection fan enhances cooking performance through fast, forced air movement.
Causes of a bad convection fan include a failed motor, worn-out blades, or blockages that disrupt airflow.
Symptoms of a bad convection fan include:
This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
Burner not heating or heating unevenly? This surface heating element restores proper heat generation. Requires removing cooktop access panel.
White plastic end cap that secures door shelf bars on refrigerator doors. Replaces broken, cracked, or missing supports. Fits both left and right sides.
Replaced broken parts. Read more
Oven won't ignite or clicks but doesn't light? This bake burner with spark igniter fixes grounding issues and ignition failures. Easy DIY repair.
Replaced igniter under oven floor panel. Read more
Replacement oven door hinge supports and controls door movement. Install if your hinge is worn, broken, or causing the door to stick, sag, or misalign.
We had to pry the door open with a crow bar. We then ordered a replacement hinge from your company. We were able to find the part by looking at your diagram of our oven. We ordered it and it came in two days. My husband put it on and the door now works beautifully. Read more
Gas pressure regulator for cooktops and ranges. Installs on the gas supply line to control flow to burners. Replace if cracked, leaking, or missing.
When I moved in to my new house I noticed there was no regulator, and the gas line was copper tubing. I ordered a regulator and ran 40 of trac pipe to make it up to code. Hooking up the regulator was easy. Read more
Transparent glass panel for your range oven door. Replace when cracked, broken, or clouded to restore clear viewing and proper heat insulation.
Fix an oven that won't heat, shuts off randomly, or has a blank display. This control board manages temperature and timing. DIY install in 1 hour.
Replaced part but I NEVER RECEIVED AN INVOICE SHOWING PAYMENT> PLEASE SEND NEED FOR OWNER> Read more
Oven won't heat, display blank, or controls unresponsive? This range control board manages temperature and cooking modes. DIY install in 15-30 minutes.
ORDERED A CONTROL PANEL. IT ARRIVED QUICKLY, WAS INSTALLED (BY A FRIEND) IN LESS THAN AN HOUR AND WORKS BEAUTIFULLY. . Read more
Replaces cracked, broken, or missing trim on your range door. Restores a finished look, holds glass in place, and eliminates gaps around the door edge.
Ordered glass and trim kit and replaced them myself. Read more
Broiler not heating or browning food? A faulty broil element is often the cause. Located at the top of the oven, this part restores even heat for broiling.
Cut off power ,inside I remove the two back screws, remove the two front screws with hangers. Pull element out, clip wires so they don't fall back in holes with clothes pins. worked good. But wire connection to the broiler was to large, had to replace connectors, wire fell in hole, had to pull wall oven out and remove back panel. I then mounted the new element to oven. Replaced connectors ,connected connectors, closed back panel, put oven in place ,connected power lines. Turned power on. Works... Read more