Kenmore / Sears Range / Cooktop / Oven Parts

This left-side oven door hinge supports the door and controls its spring-loaded movement so it opens smoothly and closes firmly, helping maintain a tight seal and consistent cooking performance.

• Provides spring tension and a pivot point for controlled opening and closing
• Aligns and pulls the door fully closed against the gasket
• Restores smooth, even door movement
• Common symptoms of a worn hinge: door won't close fully or sags; slams/falls open; feels loose or stiff; heat escaping or oven light staying on

• Disconnect power and let the oven cool completely before servicing
• Support the door; engage hinge locks or remove the door at the stop position per your model
• Springs are under tension—use gloves and caution
• After installation, verify alignment and that the door closes and seals properly

The Infinite Knob is an OEM part for GE ranges and cooktops. This part provides control over the heating elements. This knob allows users to adjust the temperature setting of their range or cooktop, ensuring accurate cooking temperatures for a variety of dishes. 

Causes for issues with the Infinite Knob often involve regular wear and tear, accidental damage from cleaning or use, or degradation of the material over time.

Symptoms of a malfunctioning Infinite Knob include:

• Difficulty in adjusting the temperature setting
• The knob slipping or failing to engage with the control shaft
• Visible wear or damage to the knob

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This oven bake element generates the heat for the Bake cycle. Replace it when the oven won't heat or takes too long to reach temperature to help restore consistent, even baking performance.

• Provides primary heat during the Bake mode
• Common symptoms of failure: no heat in Bake, very slow preheat, uneven or undercooked results
• Element shows visible damage such as blisters, breaks, or burned spots
• Replacing a failed element can restore normal oven operation

• Disconnect power at the breaker; ovens use high voltage
• Remove oven racks and access the element from the oven cavity; note screw locations and wiring
• Move wires to the new element one at a time and ensure snug terminal connections
• Avoid bending the element or overtightening screws; restore power and test Bake

This broil element mounts at the top of the oven cavity and delivers radiant heat for broiling and top-browning. Replace a broken or burned-out element to restore consistent broil performance.

• Emits high, radiant heat from the top of the oven during the broil cycle
• Used to sear and top-brown foods
• Replaces the original broil element on compatible units
• Common symptoms: No heat in broil, element won't glow, uneven top browning, visible cracks/blistering on the element

• Disconnect power at the breaker or unplug the appliance before servicing
• Remove oven racks; support the element while removing mounting screws
• Carefully pull the element forward and disconnect the wire terminals; avoid bending the element
• Attach the new element, secure with screws, ensure it is clear of the oven liner, then restore power and test

The Infinite Switch is an OEM replacement part for Whirlpool ranges. It is responsible for regulating the power and heat output of the surface elements on your range, allowing you to adjust the temperature for cooking.

A bad surface element control infinite switch can occur due to wear and tear, electrical issues, or damage to the switch mechanism. If you notice symptoms such as inability to adjust the temperature, uneven heating, or the surface element not turning on or off, it may indicate a faulty infinite switch.

Symptoms of a bad infinite switch include:

• Inability to adjust the temperature
• Uneven heating
• Surface element not turning on or off

Restore your range by replacing the faulty or damaged surface element control infinite switch with this genuine OEM part.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
 

Left side

This pilot lamp is the control-panel indicator light for a cooking appliance. It illuminates when a surface burner or oven circuit is energized, giving a clear visual cue that heat is active. What it does

• Lights to indicate an active surface burner or oven circuit
• Restores proper "heat on" indication on the control panel
• Common failure signs: indicator light does not turn on; intermittent/flickering illumination

• 1 pilot lamp

• Disconnect power at the breaker before servicing
• Access the rear of the control panel/console to reach the lamp
• Note wire positions and transfer them one at a time to the new lamp
• Secure the lamp, reassemble, restore power, and test for proper illumination

This OEM replacement part is a relay control board for ovens. The relay control board receives signals from the main oven control board. This part regulates the oven's temperature. If the oven is no longer heating properly or maintaining temperature it might be time to replace the relay control board. Luckily replacing this board is an easy repair. To replace the relay control board, begin by turning off all power to the oven. Once the power has been shut, move the oven away from the wall to gain access to the upper back panel. Remove the panel and locate the relay control board. Snap it out of its mounting brackets and remove the wire harness connected to it. Reinsert the wire connectors to the new relay board in the correct order. Secure the new board into its mounting brackets. Reinstall the upper back panel.This genuine replacement part is sold individually and is compatible with Frigidaire, Electrolux, Gibson, Kelvinator, and Westinghouse brand ovens.

This is the electronic oven control board that manages bake and broil temperatures, oven timing, and display functions. Replacing a failed control restores accurate temperature regulation and front-panel responsiveness so your range can cook reliably again.

• Regulates oven temperature by cycling bake/broil elements per setpoint
• Controls oven timing functions and user interface/display
• Common failure signs: unresponsive buttons, error codes, inaccurate temps, no heat, or blank/erratic display
• Designed for direct replacement of the original factory control

• Disconnect power at the breaker before servicing
• Transfer overlay and wiring from the old board to the new one, noting connector positions
• Handle the PCB carefully to avoid static discharge and damage
• After installation, run a test bake cycle

This Door Trim Kit replaces a damaged or missing trim piece on the appliance door, restoring a clean, finished look and proper fit. It helps keep the door's outer components in place and eliminates gaps or rattles.

• Provides a clean, finished edge around the door and covers exposed fasteners
• Helps secure exterior door trim components as designed by the manufacturer
• Replaces cracked, warped, or missing trim that can snag or look unsightly
• Common symptoms: loose or rattling trim, visible gaps around the door, or broken/missing sections

• Disconnect power before servicing; allow hot surfaces to cool
• Support the door on a padded surface; some models require door removal
• Use non-marring tools; transfer any original clips/screws/emblems as needed
• After reassembly, check door alignment and operation

The Surface Burner Igniter is an OEM part for Whirlpool ranges and cooktops. This component is crucial for igniting the gas that fuels the surface burners, ensuring that the burners light up safely and efficiently when the control knob is turned. The igniter produces a spark that lights the gas, allowing you to cook with precision and control. The surface burner igniter wire measures approximately 43" long.

Symptoms of a failing Surface Burner Igniter include:

• The burner not lighting or taking multiple attempts to light
• Weak or no spark produced when trying to ignite the burner
• A clicking sound without ignition of the burner
• Visible damage or wear to the igniter tip

Causes of a bad surface burner igniter can include regular wear and tear from frequent use, exposure to spills and food debris that can affect its function, and electrical issues such as a short circuit or a worn-out spark module.

This OEM part is also compatible with some models from Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore.

The Broil Element is an OEM part for Whirlpool wall ovens and ranges. This heating element is responsible for the broiling function of the oven.

Located at the top of the oven cavity, the broil element functions by directing intense radiant heat downward to cook and brown food from above. 

Causes may include natural wear and damage over prolonged high-heat use. Electrical malfunctions inside the element can also cause premature failure. 

Symptoms of a bad broil element include:

• Failure of the broil function
• Diminished or uneven heating during broil cycles
• The presence of cracks, breaks or corrosion on the heating coils

This genuine OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Electrode Clip is an OEM part for GE gas ranges. This part secures the electrode, which provides the ignition spark that lights the burners.

Causes of a bad Electrode Clip can include corrosion, physical damage from impact or mishandling, or loosening over time due to heat exposure and repeated use.

Symptoms of a bad Electrode Clip include:

• Failure of the burners or oven to ignite
• Intermittent or inconsistent ignition
• Visible damage or deterioration of the clip itself

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

This electronic oven control board manages oven heating functions and the display on gas ranges. Replacing a failed board restores reliable ignition, accurate temperature control, and normal bake/broil operation.

• Regulates oven temperature by reading the sensor and cycling the gas burner through the bake/broil relays
• Drives the clock and function display
• Interprets keypad inputs to select modes and temperatures
• Common failure signs: oven won't heat or maintain temperature, blank or erratic display, unresponsive controls, or recurring fault alerts

• Disconnect power at the breaker and shut off gas before servicing
• Use ESD protection and handle the board by the edges
• Photograph wiring and transfer connectors one at a time; reinstall using existing hardware
• Some models require transferring the original keypad/overlay to the new board

Includes the oven safety gas valve and pressure regulator.

The Burner Cap is an OEM part for GE gas ranges. This component sits on top of the burner head, dispersing the flame evenly for optimal cooking performance and protecting the burner head from spills and debris.

You should replace the burner cap if it becomes damaged or worn out. Causes of a bad burner cap can include exposure to high temperatures, accidental drops or impacts, and buildup of food residues or cleaning chemicals that can erode the surface over time.

Symptoms of a bad burner cap include:

• Uneven flame distribution or yellow flames
• Difficulty in igniting the burner
• Visible cracks, chips, or warping on the cap
• Poor cooking performance due to inconsistent heat

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.