Kenmore / Sears Refrigerator Control Board

Freezer icing up or fridge warm while freezer works? The defrost timer controls defrost cycles. DIY-friendly fix in about 1 hour, saves $150+ on service.

Fixes refrigerator not cooling, dispenser won't stop running, or unresponsive controls. Main control board regulates temperature and defrost cycles.

Refrigerator completely dead or not cooling? This main power control board manages the compressor, fans, and defrost system. DIY repair in 15 minutes.

Fixes refrigerator not defrosting or freezer icing up. This adaptive defrost control board manages defrost cycles. DIY-friendly repair.

This electronic control board manages key refrigerator functions including compressor operation, defrost cycles, and temperature regulation. It receives input from sensors and user controls to maintain proper cooling in both the fresh food and freezer compartments. Replace this board if the refrigerator is not cooling, displays error codes, runs continuously, or exhibits erratic temperature behavior.

Fix a dispenser that won't shut off or stops responding. This control module manages water and ice dispensing functions. DIY-friendly repair.

Refrigerator not cooling or ice maker stopped working? This main power control board manages core functions and power distribution. DIY-friendly repair.

This is a high-quality refrigerator power supply board. It's an internal component that is made to control the refrigerator functions. This part is made with small precision parts to help with timing defrost and cooling cycles. This part can be damaged or malfunction and stop operating correctly. This may prevent the refrigerator from running, cause strange sounds, or cause the refrigerator to run at the wrong temperature.If this part is damaged, it will need to be replaced. Before replacing the power supply board, make sure the refrigerator is unplugged from the wall. The process will require a flathead screwdriver and a nut driver. Use the tools to unthread the screws on the access cover. Depress the retaining tab to remove the inner cover and disconnect the wires. Press the tab to release the power supply board and snap in the new component. Make sure the wires are properly connected and reassemble.This genuine OEM replacement part is sold on an individual basis. It is directly acquired from the manufacturer and is designed to be compatible with refrigerators made by Kenmore, Whirlpool, Maytag, and KitchenAid.

This is an electromechanical defrost timer that controls the automatic defrost cycle in a refrigerator. It periodically switches the compressor off and activates the defrost heater to melt frost buildup on the evaporator coils. Replace this timer if your refrigerator is not defrosting properly, frost is building up excessively on the back wall of the freezer, or the compressor runs continuously without cycling into defrost mode.

Fix a refrigerator that won't cool, turn on after defrost, or shows error codes. This electronic control board manages power and timing for all functions.

Fix a refrigerator that beeps continuously, won't dispense ice or water, or shows unresponsive controls by replacing the control board. Moderate DIY repair.

Fix clicking relay sounds, frozen fresh food, or warm freezer temps with this refrigerator control board. Regulates defrost cycles and cooling functions.

This electronic main control board manages and distributes power to the appliance's key components. Replace a failed board to restore normal operation when the unit won't power up, won't start, or runs erratically.

• Regulates and routes incoming power to motors, fans, compressors, heaters, and valves based on signals from sensors and the user interface
• Coordinates cycle timing and system protections to help prevent component damage
• Logs or triggers fault indications when abnormal conditions are detected
• Common failure symptoms: no power, dead/unresponsive controls, intermittent shutdowns, or unpredictable operation

• Disconnect power at the breaker or unplug the appliance before servicing
• Handle the PCB by the edges and use ESD protection to avoid static damage
• Photograph wiring and move connectors one at a time to the new board
• Inspect connected loads (motors, heaters, compressor, valves) for shorts before restoring power

Refrigerator not cooling or showing error codes? This main control board coordinates the compressor, fans, and defrost cycle. Moderate DIY difficulty.

Replacement LED assembly restores screen illumination by replacing the TV's failed LED strips. Use this part to address dim, flickering, or uneven backlighting and improve overall picture visibility. What it does:

• Replaces the TV's backlight LED strips to restore even panel illumination.
• Commonly used when the screen is dim, has dark bands or spots, or the backlight flickers or fails while a faint image remains.
• Fits into the original LED channels and connects to the existing LED driver/board (direct-fit replacement when matched to correct model).
• Does not address unrelated failures such as main board, power supply, or panel matrix faults.

• Disconnect power and allow the TV to sit unpowered before starting—work only when fully de-energized.
• Handle the LCD panel and assembly carefully to avoid pressure damage; wear ESD protection when available.
• Verify LED operation before full reassembly (power up with the panel/coverings off only if you are comfortable and it's safe to do so).

Fridge not cooling, freezer too warm, or lights flickering? The main control board manages temperature and defrost cycles. Moderate DIY repair.