Kenmore / Sears Refrigerator Door

This small permanent magnet is used in supported refrigerator assemblies to actuate a mating reed switch or metal keeper. It helps the appliance recognize a closed position or hold a light cover/door closed for proper operation. What it does:

• Works with a reed switch or ferrous keeper to provide position sensing or magnetic latching
• Helps ensure features dependent on closed position operate correctly
• Can resolve issues where a small cover or door won't stay closed
• Address erratic "door ajar" indications tied to magnetic sensing

• Disconnect power and water before servicing
• Note the original magnet's location and orientation; polarity matters for proper operation
• Seat the magnet fully in its pocket or holder and align with the mating switch/keeper
• Test the related function before reassembling panels and trim

This piece replaces the flip-up cover for the cheese/butter compartment on your refrigerator door. It restores a tidy, enclosed spot for butter and small dairy items, helping keep contents contained and easy to access.

• Covers the dairy bin on the fresh food door; flips up for quick access
• Helps contain and protect butter/cheese items to reduce spills and mess
• Replace when cracked, warped, missing, or no longer stays attached/closed
• Designed to fit the designated hinge points for the dairy compartment on applicable models

• Disconnect power before servicing
• Allow plastic parts to warm to room temperature to reduce risk of cracking
• Align door tabs with the hinge posts on the compartment and press until fully seated
• Open and close the door to ensure smooth operation

This mullion rail is the trim piece that secures and finishes the gap between refrigerator doors, improving seal alignment and giving the cabinet a clean, finished look. It restores proper door fit and appearance. What it does:

• Holds the mullion/trim in place along the door opening for a consistent seal and appearance
• Helps keep door gaskets aligned to reduce drafts and improve cooling consistency
• Prevents the trim from flexing or separating when doors are opened and closed
• Addresses visible trim damage, loose or missing mullion pieces, and uneven door gaps

• One mullion rail trim piece

• Disconnect power to the appliance before starting work to avoid injury
• Remove any door liners or screws that cover the mullion before replacing the rail
• Handle trim and clips carefully to avoid cracking; small retaining clips or screws may be reused if undamaged

This center mullion kit replaces the vertical trim piece between refrigerator doors to restore a finished appearance and help maintain the door seal. It fits the factory location and matches the original trim profile. What it does:

• Replaces cracked, warped or cosmetically damaged center trim
• Restores the gap cover between doors for a clean, finished look
• Helps maintain proper door alignment and reduces drafts at the door joint
• Matches original mounting points for a direct-fit replacement

• One center mullion kit

• Always unplug the appliance or switch off power at the breaker before beginning any repair
• Remove doors or inner liners only if required by your model's service instructions; follow manufacturer guidance
• Use basic hand tools to remove fasteners and align the replacement trim; avoid over-tightening screws

Color: White

This dairy door is the flip-up cover for the refrigerator's dairy compartment on the fresh-food door. It keeps butter and cheese covered and contained, restoring a clean, finished look when the original cover is cracked or missing.

• Covers the dairy compartment and hinges open for easy access
• Helps keep small dairy items contained and organized on the door
• Replaces a cracked, warped, discolored, loose, or missing cover
• Closes properly when seated on the original hinge posts

• Disconnect power before servicing
• Remove the old cover by releasing its tabs from the hinge posts
• Align the new cover with the hinge posts and press to snap into place
• Avoid forcing brittle plastic; allow the part to reach room temperature before installation

Color: White

Note: This is a 2 door kit with both the Refrigerator and Freezer doors.

Color: Black

Note: This is a 2 door kit with both the Refrigerator and Freezer doors.
 

This replacement inner door panel restores the interior surface of the door. It supports door bins/shelves and provides a stable surface for the door gasket to seal, helping keep cold air in and items secure.

• Forms the interior face of the door and supports door bins/shelves
• Provides the gasket with a flat surface to help maintain a proper seal
• Replace if cracked, warped, or separating from the door frame
• Common symptoms include loose/falling door bins, visible damage, or air leaks/frost near the door

• Disconnect power and empty items from the door before service
• Remove the door per the appliance manual and lay it flat to prevent twisting
• Transfer the door gasket and any reusable hardware from the old panel if applicable
• Install the new panel and tighten fasteners evenly; verify the gasket seals all around

Access door provides a finished cover for the appliance's service opening, protecting internal components from dust and damage while keeping the unit looking tidy and allowing access for maintenance and repairs. What it does:

• Covers the service or access opening and protects wiring, valves, and other internal parts.
• Allows access to controls, connections, or components for inspection and repair without removing major panels.
• Helps prevent debris, pets, or fingers from contacting internal parts.
• Replace a missing, cracked, or damaged access door to restore appearance and reduce exposure of internal components.

• Always disconnect power (and gas for gas appliances) before removing panels or working on the appliance.
• Handle the door and surrounding edges carefully to avoid cuts; keep original fasteners and reuse if undamaged.
• Align tabs/clips and secure with manufacturer screws; do not overtighten.