Need Help?
Call or text
If your range has no power or burnt plastic smell, the terminal block may be melted. This kit restores secure power connections. Moderate DIY repair.
Replaced the terminal block. Read more
Replace a gas range burner valve that's broken, stuck open, or causing hard-to-adjust flames. Moderate DIY repair requires raising the stovetop.
After turning off the gas and unplugging the electricity, I removed all the burners from the stove top using a 3/16" hex socket. Then used a 1/4" socket to removed two or three screws under each burner which hold the burner base to the bottom of the top panel. Then pulled all the knobs and removed the front panel which was held in by two Phillips screws accessible from underneath the panel. It helps to open the oven door to get at these screws. With the knob panel gone, I removed two screws... Read more
Burner won't light or clicking with no spark? This igniter creates the spark to light gas burners. Easy press-fit installation takes 15 minutes.
I removed all the individual burners so I could lift the stainless cover to expose the igniter wires. I cleaned all the wire connections and the 4 good igniters and replaced the one bad igniter. Reassembly was easy and everything worked properly when done. Video of repair was helpful and all parts ordered were correct and shipped promptly and I will definitely use AppliancePartsPros again. Read more
Burner orifice spud regulates gas flow to the burner on your range or cooktop. Replace if missing, damaged, or when converting between LP and natural gas.
I bought a new orifice and installed it. Read more
Replace your worn oven door gasket to improve heating efficiency and prevent heat loss. Restores proper seal between door and cavity. Confirm fit by model.
I replaced the old control panel with a new one. I also changed out the door seal to help prevent the control panel from going bad a second time. It was the heat from the oven getting to the keypad on the control panel that caused it to go bad. Read more
Oven won't heat or bake properly? A failed bake element is usually the cause. This bottom heating element restores even baking. Easy 15-minute DIY fix.
It's was easy to replace. Unplugged the oven from the wall, unscrew the two screws that hold the element to the back of the oven and pulled it away from the oven. Then just pull off the two wires at the end of the bake element. Install the new one in the revers order, easy. Read more
Burner won't turn off or element light stays on? This range burner control switch regulates temperature and power. Moderate DIY repair, 30-60 minutes.
I went on your website found the parts needed to make the repairs. I watched the short video on installation. The parts arrived just a few days after I placed the order. I finished the repair in less than an hour and had to wait a few minutes to test the switch since the power was off and on due to a wind storm. Simple easy to do repair and I saved $90.00 on service fee for a tech to do the repair. Read more
Bushing sleeve that fits inside range control knobs to reduce friction and ensure smooth turning. Replace if knob feels loose, wobbly, or damaged.
Order the knob and bushing. Fit and looked better then original knobs that came with gas range. Read more
Burner not heating evenly or has hot spots? This 6-inch surface element coil restores consistent heat for simmering and boiling. Simple plug-in fix.
Bought replacement burner receptacles. Cut off the old ones, used wire nuts to connect replacements. Read more
White adhesive clock overlay for oven control panels. Peels off and sticks on to replace cracked, worn, or faded overlays. Easy cosmetic upgrade.
My husband turned the oven to cook one night and there was a loud pop noise. After that there was no power getting to the control board and thus leaving my oven useless I watched the very easy to follow video posted on here associated with my part and I felt confident I would be able to make this repair on my own. I bought the control board as well as the new overlay (mainly cause I didn't want to try and peel off the old overlay and reuse it) the total time for my repair was less than 15... Read more
Fix a burner that won't turn off or heat properly with this dual infinite switch. Controls both inner and outer element rings. Moderate DIY repair.
Relatively easy DIY Read more
Protective plastic overlay for your range control panel. Replaces cracked, discolored, or worn overlays from heat exposure or repeated cleaning.
Called appliance parts pros because I couldn't find it on their website talked to an associate it didn't take 5 minutes and the part was ordered! It was delivered very quickly and was the exact same as the old one! It was a very pleasant experience! Read more
Burner not heating or heating unevenly? This surface element restores consistent heat to your electric cooktop. DIY-friendly repair, typically 15-20 minutes.
Went to YouTube for pictorial on the repair. Found it to be an easy replacement. Made a wiring chart, followed the reverse order of wiring. Installed part checked that part floated on its spring mounts and did not touch anything. Checked my wiring a second time agents my chart-making shore all spade connections were tight. lowered and secured top turned power back on and tested part.. Part functions correctly. Read more
The Cap-Burner Kit is an OEM part for Whirlpool ranges. It includes the required 4 burner caps. (2 large, 1 medium, 1 small) to replace a faulty gas burner on the cooktop.
Causes may be normal wear over years of heating cycles, chemi
Burner not heating or working? This radiant surface element sits beneath glass cooktops to restore consistent heat. Quick plug-in repair most DIYers complete.
Ordered part from AppliancePartsPros.com and replaced it. Read more
This 6-inch drip bowl installs beneath the coil element on your electric range. Replace if cracked, chipped, or heavily discolored from spills.
Bought new ones and put in. Read more