Kenmore / Sears Wall Oven Parts

Replace dispenser micro switch. Also replaced broken faceplate and rusty screws. Appliance parts Pro YouTube video was helpful in diagnosis and disassembly. Parts arrived quickly. Read more

I diagnosed this problem via the web and the advice was spot on. The problem was a failure of the bottom door switch. I used a multimeter to verify that the switched never closed properly. It took me a minute to figure out how to remove the old switch (press a release tab under the switch while simultaneously rotating counter-clockwise). That was about the most difficult part of the repair. Read more

I bought a new orifice and installed it. Read more

• Element will not heat

The burners and drip pans that I previously ordered fit this stove perfectly. It is so much better cooking on the cook stove with the burners laying properly. I'm very pleased. My only complaint is that I wish more parts were available for this old stove, I really love it! Read more

I bought the replacement drip bowl - large and the rubber gasket which was delivered quickly. Specific steps: 1)turn off electricity to cook top 2) remove burner grate, burner cap and collar 3) remove two Philips head screws near center hole 4)lift out drip bowl and reach under it to remove electric plug to igniter. Note how old gasket fits on drip bowl. 5)take out retaining clip on igniter and remove igniter 6)clean up surface where new drip bowl will contact cooktop 7)stretch new rubber... Read more

Replaced with new ones. Read more

Found the parts I needed ordered them from your site Received them and installed in a few minuets and was done Read more

What you will need: * replacement parts * small and regular Phillips screwdrivers * small wrench * soapy water in a spray bottle or leak detection spray Take apart the top of the stove control unit 1) turn off the gas to the stove, in my case I cannot get to the shutoff valve easily so I ended up turning off the electricity to the stove at the fuse box as that forces an emergency shutdown of the gas supply internally of the stove. 2) remove all 5 knobs, the grates at the top and open the oven... Read more

Bought replacement burner receptacles. Cut off the old ones, used wire nuts to connect replacements. Read more

I orderd parts you said I needed, but all I needed was a handle. I will keep other parts for future needs Read more

Replaced the pressure regulator. Read more

Replaced faulty latch with new latch. New latch was different configuration, but the fit was okay. The only issue was that the wires to the electric motor were just barely long enough. Overall easy repair if you have a T15 Torx bit, phillips screwdriver, and 1/4" nut driver. Hardest part is removing the gas cooktop to gain access to the cleaning latch. 0. Turn off electric to stove; remove the cast iron grates, center caps/orifices, and catch pans from the stovetop. 1. Disconnect the... Read more

Replaced the inside door glass. Read more

After turning off the gas and unplugging the electricity, I removed all the burners from the stove top using a 3/16" hex socket. Then used a 1/4" socket to removed two or three screws under each burner which hold the burner base to the bottom of the top panel. Then pulled all the knobs and removed the front panel which was held in by two Phillips screws accessible from underneath the panel. It helps to open the oven door to get at these screws. With the knob panel gone, I removed two screws... Read more

First, I just unscrewed all nuts that are holding the frame and all surface elements. Once all parts, surface elements, control switches, are loose from the original glass, I just moved all parts to the new glass. Due to the weight of the glass, all actions have to be done carefully as I broken one corner of the glass couple of years ago when I replaced one of the control switch. Read more

Move stove to unplug, remove rear center panel, indentify the two spade connectors that feed the heating element and remove (unplug) them. Remove two screws that hold the element to the inside rear wall of the stove and remove element. Install new element, plug in the previously removed spade connectors, re-install rear center panel, plug range (power) in, move stove back into place and enjoy. Read more