Kitchenaid Axle, Roller, Pulley Parts

This planetary drip ring fits around a stand mixer's planetary assembly to cover the gap below the gearcase and help catch grease residue, restoring a clean, finished look where the beater hub meets the mixer head.

• Mounts at the base of the mixer head around the planetary housing
• Helps deflect incidental gearbox grease residue away from the bowl area
• Covers the seam between housing and planetary for a clean, finished appearance
• Replace if bent, cracked, loose, missing, or if you notice grease spotting beneath the planetary

• Unplug the mixer and remove the bowl and attachments
• Gently pry off the old ring; clean the seating surface of debris or residue
• Align and press the new ring evenly until fully seated; avoid deforming the ring or striking the gearcase
• On some models, access may require lowering/removing the planetary

Color: White

This drive coupling connects the motor shaft to the blender jar. Replace if worn, stripped, or cracked to restore proper blade rotation and function.

Replaces damaged dishwasher dishrack wheel assembly. Installs on upper or lower rack for smooth rolling. Needed when wheels crack or tabs break.

Replace cracked or worn dishwasher dishrack wheels that guide the upper rack in and out smoothly. Single wheel for convenient loading and unloading.

Replacement tub wheel that supports and guides the washer drum for smooth, aligned rotation. Replace worn wheels to reduce drum noise, rubbing and uneven spinning. What it does:

• Supports and guides the washer drum so it turns smoothly and stays aligned.
• Reduces friction between the drum and cabinet, helping prevent scraping or binding.
• Replace if the drum squeaks, drags, rubs, or wobbles during spin cycles.

• Disconnect power and turn off water supply before servicing the appliance.
• Access may require removing the cabinet, front or rear panel depending on model.
• Inspect adjacent shafts, bearings and mounts for wear and replace if needed.
• Reassemble and test the washer after installation to ensure proper drum movement.

Replacement wheel for dishwasher lower rack. Attaches to the dishrack to allow smooth gliding during loading. Needed when wheels are cracked or worn.

Rear support wheel for dishwasher lower rack assembly. Replaces broken, cracked, or missing wheels that cause dragging or misalignment on the track.

This stud is a small mounting fastener that provides a secure anchor point for attaching appliance components. Replacing a worn or missing stud restores a tight, aligned fit and helps prevent looseness, rattles, or shifting.

• Provides a fixed, threaded anchor for mounting a handle, bracket, or panel
• Helps keep parts aligned and secure during normal operation
• Common replacement for studs that are stripped, bent, broken, or missing
• Symptoms can include a loose or wobbly component, difficulty tightening, or visible damage/corrosion

• Disconnect power and, if applicable, shut off water or gas before servicing
• Wear cut-resistant gloves and handle panels carefully
• Hand-start threads to avoid cross-threading; tighten snugly without over-torquing
• Reinstall any covers or related hardware in their original positions

Rear wheel support that guides and stabilizes the dishwasher rack as it slides. Replace if cracked, broken, or worn to restore smooth gliding motion.

The Lower Dishrack Roller Assembly is an OEM part for Whirlpool dishwashers. As an integral component, the lower dishrack roller assembly supports smooth movement and positioning of the lower dishrack. Its precision ball bearings allow for effortless extension and retraction of the lower rack.

Causes of a bad lower dishrack roller assembly can include wear and tear of bearings over time, stripped or damaged rails, or failure of rollers due to excessive loading.  

Symptoms of a bad lower dishrack roller assembly include:

• Difficulty extending or retracting the lower dishrack  
• Noisy or stuck operation of the lower rack
• Rack failing to remain securely in place during wash cycles
• Dishes shifting or falling during wash due to uneven support

This OEM Whirlpool part is also compatible with KitchenAid, Jenn-Air, Amana, Kenmore, and some Maytag and GE dishwashers. 

Color: Metallic Chrome

Planetary gear assembly for stand mixers. Mounts inside the mixer head to rotate beaters and attachments. Replace if teeth are stripped or worn.