Kitchenaid Dishwasher Control Board

This electronic control board is the dishwasher's main circuit board. It directs wash, drain, and dry functions and coordinates the user interface. Replacing a failed board restores responsive controls and reliable, complete cycles.

• Times and sequences wash, drain, and dry operations
• Distributes power to the circulation pump, drain pump, inlet valve, and heating circuit
• Monitors sensors and door switch; communicates with the display/indicator lights
• Common symptoms: won't start, unresponsive controls, cycles that stall or never advance, blinking lights or error codes

• Disconnect power at the breaker before servicing; verify no voltage is present
• Use ESD protection and handle the board by its edges
• Label/photograph connectors; transfer any mounting brackets or jumpers from the original board
• Some models require configuration/programming after install—follow the tech sheet stored inside the unit

This speed control regulates and stabilizes motor speed in your appliance. Replacing a faulty control restores smooth start-up and accurate speed selection so the motor runs consistently at the setting you choose.

• Modulates power to the motor to reach and hold the selected speed
• Helps correct issues like surging, stalling, or running only at one speed
• Common symptoms include erratic speeds, failure to start, or sudden speed changes
• Also presents as an unresponsive speed selector or inconsistent performance

• Disconnect power before servicing and allow components to discharge
• Access the control per your model's service information; note wire locations or take photos
• Transfer connectors one at a time; seat fully and handle electronics with ESD care
• Reassemble and test operation through all speed settings; perform any model-specific calibration if required

This electronic control board is the appliance's central controller, managing critical functions and timing. Replacing a failed board restores proper operation, responsive controls, and consistent performance when the unit is unresponsive, shows errors, or behaves unpredictably.

• Processes user commands and internal signals to run cycles as designed
• Controls or communicates with motors, valves, fans, and heaters through onboard components
• Manages timing, temperatures, and safety checks programmed by the manufacturer
• Symptoms of failure: won't power on or start, dead or erratic controls, error codes, intermittent operation

• Disconnect power to the appliance before servicing; also shut off gas/water
• Use anti-static precautions and handle the board by its edges
• Photograph connections; transfer connectors one at a time to the new board; secure in the original mounting
• After installation, follow your model's tech sheet for any required initialization/diagnostics and verify normal operation

This is a Whirlpool control board intended for use with dishwashers.The control board is a critical component of the dishwasher as it controls the cycles and functions, including the draining and drying cycles. Control boards are subject to wear and tear that can render them ineffective and require them to be replaced prior to the standard lifecycle of the appliance. Unplug the dishwasher from both the power and water sources before attempting to replace the control board to prevent serious electrocution injuries. Work gloves should also be worn.This OEM control board has been sourced from the manufacturer and is compatible with dishwashers from Whirlpool, Maytag, Kitchenaid, Magic Chef, Admiral, Norge, and other brands. This part has been made from high-quality, durable, non-corrosive materials and is only sold individually.

This user interface is the electronics behind a full-door console dishwasher panel. It reads your button selections and communicates with the main control so cycles start and options respond reliably.

• Interprets keypad inputs from the console and sends commands to the control board
• Helps restore proper control of wash cycles, options, and start/delay functions
• Common symptoms: unresponsive or intermittent buttons, no console lights, can't start from the panel, erratic beeping/stuck-key behavior
• Built for full-door (full-console) configurations used on select models

• Disconnect power at the breaker; turn off the water supply
• Remove inner door/console screws to access the UI; support the panel to avoid straining wires
• Handle the board with ESD care; transfer any mounting clips/brackets and seat ribbon cables/connectors fully and correctly
• Reassemble the door and test console operation before running a full cycle

This electronic control board is the appliance's main control. It directs power and timing to the correct components so cycles run as selected, helping restore consistent operation when the original board has failed.

• Coordinates operation of motors, valves, heaters, and pumps
• Interprets inputs from switches and sensors to manage cycle logic
• Stores and executes programmed options and settings
• Typical symptoms: won't start or advance, unresponsive or flashing controls, error codes, intermittent shutdowns

• Disconnect power before servicing; use ESD protection and handle the board by its edges
• Access is typically through the control console; refer to your model's service sheet for exact location
• Move wire connectors one at a time to the new board and secure it properly
• Perform any required initialization/diagnostic steps for your model after installation

The Cntrl-Elec is an OEM part for Whirlpool dishwashers. As the control and electronic component, it governs all of the major functions and operations of the dishwasher. The control board contains integrated circuits, microprocessors, and electronic components that facilitate cycles, temperature regulation, safety features, and user input.

Over time, the electronic components inside the controller can degrade or become damaged. Environmental factors like surges, fluctuations in power, and other electrical issues may also potentially cause failure. 

Symptoms of a bad controller can include:

• Not operating or cycling at all
• Inability to start or stop cycles
• Fault codes displayed
• Issues with heating or drying
• Buttons or control panel not responding

This genuine OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Control Board is an OEM part for Whirlpool dishwashers. As the central processing unit, this board regulates all cycles and component functions including wash and rinse settings, heating controls and the digital display.

Symptoms of a failed control board include:

• Inability to select or change wash/rinse options
• Cycles failing to complete through all settings
• Error codes displayed or unresponsive controls

Causes can be normal wear of electronic components over extended use. Exposure to fluctuating internal temperatures may also deteriorate electrical connections over time.

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

This electronic control board is the appliance's central controller. It interprets user inputs and sensor signals to power components at the right time, restoring reliable operation when the original board fails.

• Interprets user settings and manages cycle timing and temperature control
• Switches relays/outputs to run motors, heaters, valves, fans, and lights
• Interfaces with sensors and safety switches to protect the appliance
• Symptoms can include no display or response, won't start, cycles that won't advance, or erratic operation
• Logs diagnostic error codes to aid troubleshooting

• Disconnect power before servicing; follow ESD precautions and handle the board by the edges
• Access the control area, then note/photograph wiring and move connectors one at a time to the new board
• Mount securely, ensure no wires are pinched, reassemble, and restore power
• Run a diagnostic or test cycle to confirm normal operation

This electronic control board is the appliance's main brain. It manages cycles and powers key components based on sensor and user input, restoring normal operation and responsive controls when the original board fails.

• Directs the appliance's operations by processing inputs from sensors and the user interface
• Distributes power to motors, valves, heaters, fans, and other loads as needed
• Monitors system status and logs/communicates fault or error codes
• Typical failure symptoms: won't start, unresponsive controls, stops mid-cycle, intermittent power, or recurring error codes

• Disconnect power to the appliance before servicing
• Use ESD protection and handle the board by its edges
• Photograph wire/connector positions; transfer connectors one at a time to the new board
• Ensure all harnesses are fully seated and the board is secured; run a diagnostic or test cycle after installation