Lg Washer Parts

Flexible rubber seal around the door opening that prevents leaks during wash and spin cycles. Replace if torn, cracked, or moldy. Confirm fit with your washer model number.

This power control board is the appliance's main electronic PCB. It manages power distribution and control logic, coordinating sensors and user inputs so the unit's motors, fans, heaters, and valves run when they should. What it does:

• Distributes and regulates power to key components through onboard relays
• Processes sensor feedback and timing to execute programmed operations
• Coordinates operation of motors, fans, heaters, and valves as required
• Common failure symptoms: unit won't power on or start, unresponsive controls/display, intermittent or erratic operation, repeated clicking from the control area, or error codes

• 1 electronic control board assembly

• Disconnect power before servicing; verify power is off
• Use ESD protection and handle the board by the edges
• Photograph/label connectors and transfer plugs one at a time, ensuring proper seating and orientation
• Secure the board, reassemble covers, restore power, and verify normal operation

This tub-to-pump hose connects the washer's outer tub to the drain pump, carrying water out during the drain cycle. Replace it to resolve leaks or drain errors caused by cracks, splits, or internal blockages.

• Routes wash water from the outer tub to the drain pump
• Flexible bellows section helps prevent kinking and accommodates tub movement
• Failure signs: water leaking under the washer, slow/no draining, drain-related error codes, or visible cracks/soft spots
• Often needed after clamp corrosion, physical damage, or age-related deterioration

• Unplug the washer and turn off water supply; drain any remaining water from the tub/hoses
• Access location varies by model; remove panels as needed to reach the hose and clamps
• Use pliers to release spring clamps; note routing and clamp orientation before removal
• Seat the hose fully on fittings, secure clamps, and test with a short drain/rinse cycle to check for leaks

This is a flexible rubber bellows that connects the dryer exhaust outlet to the external vent duct on a combination washer/dryer unit. It channels hot, moist air out of the dryer section and helps absorb vibration during operation. Replace this bellows if it is cracked, torn, or collapsed, which can cause poor drying performance, excessive lint buildup, or moisture leaking inside the unit.

Spider arm connects the wash basket to the drive shaft in front-load washers. Replace if cracked, corroded, or broken to restore proper basket support.

Washer won't spin or shows LE error? A failed stator loses the magnetic field needed to rotate the drum. Moderately difficult repair with rotor removal.

This is a plastic lifter baffle that mounts inside the dryer drum. It tumbles and lifts clothes as the drum rotates, promoting even airflow and efficient drying. Replace this part if it is cracked, broken, or missing, which can result in clothes bunching together, uneven drying, or loud thumping noises during operation.

Delivers fresh water from your home supply to your washer. Replace if cracked, leaking, worn, or damaged to restore proper fill connection.

Fix a washer that won't fill, overfills, or fills when off with a new water inlet valve. Controls hot and cold water flow into the tub during wash cycles.

Fix a washer that won't drain or leaves standing water with a new drain pump assembly. Moderately challenging repair that solves drainage issues.

Replacement wire harness for washers. Restores electrical connections between components when original wiring is damaged, frayed, or corroded. Direct fit.

This clamp secures hoses or wiring to the appliance chassis to prevent movement, chafing, and vibration-related wear. It helps keep connections stable so hoses and wires stay in place during normal use. What it does:

• Holds water, drain or vent hoses in position to reduce strain and prevent rubbing
• Keeps wiring harnesses routed and fastened to avoid chafing or accidental disconnection
• Reduces vibration-related noise caused by loose hoses or wires
• Helps prevent hose kinks and unintended movement that can lead to leaks or intermittent electrical issues

• One clamp

• Disconnect power to the appliance before servicing; shut off water supply if working with water lines
• Remove panels as needed to access the hose or wiring route, then replace the clamp in the same orientation
• Use appropriate pliers or a screwdriver if required; do not overtighten or deform the hose or wiring
• If the original clamp was secured with a fastener, retain and reuse it only if undamaged; replace any stripped or broken hardware

Fixes washer that won't start, complete cycles, or respond to controls. This main control board restores electronic functions and display communication.

Interior support trim that secures the door assembly and provides a finished surface inside your washer door. Replace when cracked, damaged, or worn.

Rear housing panel that shields internal components and maintains airflow. Replace this outer cover if cracked, broken, or missing to restore protection.

Drum bearing bushing for washers. Installs between drum and bearing assembly. Replace if cracked, worn, or missing to restore proper drum support.