Maytag Dishwasher Gasket & Seal

Gasket for upper wheel.

This seal kit is for the main tub. It goes around the pump housing.

This pump outlet seal sits on the discharge side of the dishwasher pump to keep the outlet connection watertight. Replacing a worn seal helps stop leaks and keeps wash water contained during the cycle. What it does:

• Seals the joint at the pump outlet to prevent water leakage
• Helps maintain proper circulation by keeping the pump discharge airtight/watertight
• Common symptoms of failure include water under the unit, drips near the pump area, or a flattened/cracked/hardened old seal

• 1 pump outlet seal

• Disconnect power and shut off the water supply before servicing
• Remove the toe-kick/lower access panel to reach the pump area; place a towel or pan to catch residual water
• Note seal orientation; clean mating surfaces before installing the new seal
• Seat the seal evenly; reassemble and run a short test to check for leaks

This dishwasher water deflector redirects spray back into the tub at the front edge, helping prevent splash-over and leaks during cycles. Replace a cracked, warped, or missing deflector to keep floors dry and wash performance consistent.

• Directs wash water away from the door opening and front corners
• Helps reduce leaks and puddles at the bottom front of the dishwasher
• Restores proper containment when the original deflector is deformed, loose, or missing
• Common symptoms include water on the floor at the front, drips during cycles, or visible damage to the deflector

• Disconnect power and turn off the water supply before servicing
• Open the door to access the front/tub area; remove the old deflector
• Clean the mating area and seat the new deflector fully and evenly
• Run a short test cycle and check for leaks

This dishwasher door seal fits into the tub channel to create a tight, water-resistant barrier when the door closes. Replacing a worn gasket helps stop nuisance leaks and restores proper door compression and moisture containment.

• Creates the primary seal around the dishwasher tub opening when the door is closed
• Helps keep wash water, suds, and steam inside the wash cavity
• Wear can lead to drips at the front corners or along the sides
• Replace if the gasket is cracked, torn, flattened, or no longer sealing; the door may be harder to latch

• Disconnect power and turn off the water supply before servicing
• Remove the old gasket and thoroughly clean the channel of debris and residue
• Warm and relax the new gasket; start at the top center and press evenly into the channel without stretching
• Close the door for several hours to help the seal set; run a test cycle and check for leaks

This coupler gasket creates a tight, leak-resistant seal at a coupler connection point, helping maintain proper operation of the assembly. Replace when the original gasket is worn, cracked, or flattened to prevent drips and seepage.

• Forms the seal between a coupler and its mating component
• Helps prevent water seepage and air intrusion at the joint
• Supports correct flow/pressure through the connection
• Common symptoms: drips at the fitting, moisture around the coupler, or needing to over-tighten to stop leaks

• Disconnect power and shut off water supply before servicing
• Relieve line pressure and place a towel to catch residual water
• Clean mating surfaces; seat the gasket squarely in the coupler recess
• Tighten fittings evenly; restore service and check for leaks

This inlet/outlet seal creates a watertight barrier where two water passages meet in your appliance. Replacing a worn seal helps stop leaks at the connection and maintains proper water flow and performance.

• Forms a tight seal at an inlet/outlet connection to prevent water leaks
• Helps maintain correct water flow and pressure through the system
• Common signs of failure: drips or pooling water near the unit, visible cracks, flattening, or deformation of the seal
• Can resolve recurring leaks after reassembly of water-line connections

• Disconnect power and shut off the water supply before servicing
• Access the connection point and note the seal's orientation
• Clean mating surfaces; seat the new seal evenly without twisting
• Reassemble, restore water/power, and check carefully for leaks during a test run

Size: 1-1/16 x 5/8 inch. Used for fill hose. For a 4 pack order 285448A

This felt door vent seal fits around the dishwasher's door vent to help contain steam and moisture within the inner door. Replacing a worn seal helps prevent minor leaks and condensation around the vent area during cycles.

• Creates a gasket between the vent assembly and inner door panel to keep steam directed through the intended vent path
• Reduces moisture escape that can cause drips or water spots on the outer door or nearby countertop
• Helps limit condensation or musty odors from trapped moisture inside the door panel
• Indicators of failure include visible wear or separation of the felt and moisture around the vent during operation

• Disconnect power and turn off water supply before servicing the dishwasher
• Remove the inner door panel to access the vent assembly
• Note the seal's orientation; clean mating surfaces; seat the new felt evenly around the vent with no gaps
• Reassemble and run a short test cycle to check for leaks at the vent area

Located between the console and door

This factory washer is used in appliance assemblies to distribute load under a fastener and maintain a secure, accurate fit. Replace a missing or damaged washer to restore proper stack-up and reduce vibration, noise, or loosening.

• Distributes load and provides proper spacing in the fastener assembly
• Helps keep bolts, screws, or nuts tight to minimize vibration and rattling
• Direct replacement when the original washer is worn, bent, cracked, or missing
• Typical signs include loose panels/brackets, recurring looseness after tightening, or new vibration after service

• Unplug the appliance; shut off water supply if working near hoses or valves
• Note the original hardware stack-up and reassemble in the same order
• Inspect mating surfaces and companion hardware; replace any damaged parts
• Tighten fasteners snugly per service guidance; avoid overtightening

Note: For faucet adapter

The Lower Door Seal Assembly is an OEM part for Whirlpool dishwashers. As a key component, this seal is designed to create a tight barrier between the door interior and tub during wash cycles. The pliable rubber seal provides a sturdy gasket to block water, detergent, and sound.

Causes of failure involve mineral buildup, cracks from repeated use, or degradation of adhesive over time compromising the seal. 

Symptoms of a faulty seal assembly include: 

• Puddles or leaks from beneath the door frame
• Higher water consumption or longer cycles   
• Increased noise levels during operation

This OEM Whirlpool replacement is also compatible with select KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, and other brands.

The Seal is an OEM part for Whirlpool dishwashers. As a crucial door component, it ensures a tight fit that prevents leaks and contains the necessary heat and moisture during operation. 

Symptoms of a bad seal can include cracks, tears, or looseness allowing water to escape during cycles. Deterioration from chemical exposure or repeated flexing over time is common.

Causes of a bad seal include general wear and tear, damage from improper loading of dishes, or accidents like sharp objects puncturing the material.

Symptoms of a bad seal include: 

• Puddles or pools of water found beneath the dishwasher after cycles
• Wet floors and surfaces surrounding the dishwasher  
• Steam or moisture visible escaping during heating phases
• The door not closing or latching properly

This OEM Whirlpool replacement part is compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.