Maytag Grille

This white dispenser grille fits the refrigerator's ice/water area on the door. It provides a clean, finished surface and helps catch minor drips, restoring appearance when the original grille is cracked, stained, or missing.

• Sits beneath the ice/water dispenser opening on the door
• Helps catch small drips to protect the door surface
• Provides a finished look and covers the dispenser recess
• Common symptoms: cracked or discolored plastic, broken tabs, won't sit flat, or won't stay in place

• Most models: lift the old grille straight out; align and press the new grille into place
• Some models use retaining tabs or screws; open the door to access and release them
• Unplug the refrigerator before servicing; wear cut-resistant gloves to protect hands
• Do not force the part—plastic tabs can break if misaligned

This base grille covers the lower front of the refrigerator in a midnight gray finish. It directs airflow to the condenser and protects internal components—restoring proper ventilation and a clean, finished look when the original is damaged or missing.

• Covers the toe-kick area and helps channel cooling air through the condenser compartment
• Protects coils and lower components from bumps and debris
• Restores the unit's finished appearance
• Common symptoms include a cracked or missing grille, loose/rattling panel, or broken mounting tabs

• Disconnect power before servicing; use gloves to protect hands from sharp edges
• Open the doors; remove any retaining screws or release the grille's clips, then pull the old grille forward
• Align the new grille with the mounting points and snap or screw into place
• Ensure vents are unobstructed and the grille is secure before restoring power

This front grille covers the lower front of the refrigerator and helps guide airflow through the condenser area. Replace a cracked, loose, or missing grille to restore appearance and proper ventilation. What it does:

• Covers and protects the base area, giving the unit a finished look
• Helps channel air to the condenser for consistent ventilation
• Helps keep dust and debris from collecting under the appliance
• Common symptoms: cracked/broken grille, broken tabs, won't stay attached, missing piece

• 1 front grille

• Disconnect power before servicing
• Release retaining clips or remove any mounting screws per your model
• Align tabs and snap or fasten the new grille into place
• Reuse original screws/clips if applicable; secure attachment and clear airflow

This bottom grille covers the lower front of the refrigerator, protecting internal components and helping route airflow through the condenser area. Replace a cracked or missing grille to restore fit, appearance, and proper ventilation.

• Helps direct airflow through the base vent area for proper ventilation
• Shields lower components from bumps and debris and provides a finished look
• Common symptoms: cracked or warped panel, broken mounting tabs, rattling, won't stay attached, or missing panel
• Also called a toe grille, kick plate, or front base grille

• Disconnect power before servicing
• Remove the old grille by releasing retaining clips or screws
• Align the new grille with mounting points; snap or fasten securely
• Ensure vents are unobstructed and doors open/close without interference

This toe grille is the lower front kick panel that covers the refrigerator's base and leveling feet. It restores a clean, finished look and helps direct airflow to the condenser area for proper cooling performance.

• Covers the bottom front opening and protects components from bumps and debris
• Helps channel air across the condenser area
• Common signs it's needed: cracked or broken panel, missing grille, difficulty keeping grille attached
• Cosmetic damage or loose fit at the base of the refrigerator

• Unplug the appliance before servicing
• Open the doors to relieve pressure on the grille, then release retaining tabs or screws
• Align tabs and snap or screw the new grille into place
• Verify doors open/close freely and grille is secure

This grille is a cosmetic cover that attaches to the appliance to finish the opening and help protect internal areas. Replacing a damaged or missing grille restores a clean appearance and a secure, proper fit. What it does:

• Attaches at the designated location to provide a finished look
• Helps shield underlying components and keep debris out
• Designed to fit securely using existing clips or screws
• Common symptoms: cracked or warped plastic, broken tabs, loose fit, or missing piece

• 1 grille

• Disconnect power to the appliance (and shut off utilities if applicable) before servicing
• Remove any retaining screws or clips; gently release locking tabs to avoid damage
• Transfer reusable mounting hardware from the old grille if required
• Align and secure the grille; do not overtighten fasteners

This replacement toe grille installs at the bottom front of the refrigerator. The 30-inch black kickplate finishes the look and helps protect and ventilate the condenser area. Replace a cracked or missing grille to restore appearance and airflow.

• Covers the lower front opening and directs air through the condenser vents
• Shields base components from bumps and debris during everyday use
• Provides a clean, finished look along the floor line
• Common signs of failure: cracked or warped grille, broken mounting tabs, won't stay attached, or missing piece

• Disconnect power before servicing
• Remove the old grille by releasing retaining clips or removing screws; save any reusable hardware
• Align the new grille and snap into place or reinstall screws—do not overtighten
• Keep ventilation slots clear after installation

This white vent grille covers the front ventilation opening of the appliance, providing a finished look while allowing proper airflow. Replace a cracked or missing grille to restore appearance and ensure the vent opening is correctly protected.

• Directs air through the front vent opening while shielding internal components
• Restores secure fit when tabs or mounting points are broken
• Replaces grilles that are cracked, warped, discolored, or missing
• Can reduce rattling or vibration caused by a loose or damaged grille

• Disconnect power before servicing to prevent electrical hazard
• Remove the screws or clips securing the existing grille; release any retaining tabs
• Align the new grille with the mounting points, engage tabs, and secure with existing fasteners
• Verify the grille sits flush and does not obstruct airflow

This 30-inch toe grille covers the lower front of the refrigerator, completing the built-in look while allowing proper ventilation to the condenser area. Replace a cracked or missing kickplate to protect components and refresh the appliance's appearance. What it does:

• Covers the base/kick area at the front of the refrigerator
• Provides venting to help air flow through the condenser compartment
• Shields internal components from bumps and debris
• Restores a clean, finished exterior when the original is damaged or lost

• 1 toe grille (30 in)

• Disconnect power and wear cut-resistant gloves before starting
• Remove existing mounting screws or release retaining tabs; save hardware for reuse
• Align tabs/clips with cabinet slots and press or fasten the grille until fully seated
• Ensure vents are unobstructed and doors open/close without interference after installation

This front grille replaces the toe-kick panel at the base of the appliance. It helps protect the condenser area from debris and provides a finished look across the bottom front of the unit.

• Covers and protects the lower front opening and condenser area
• Helps direct airflow to the condenser for proper cooling performance
• Restores a clean, finished appearance when the original grille is damaged or missing
• Common signs: cracked or broken grille, missing panel, or difficulty keeping the lower area clear of debris

• Unplug the appliance and turn off water supply before starting
• Open doors and remove any screws or clips securing the grille; pull to release
• Align new grille with mounting points; snap or screw into place
• Check for secure fit and proper airflow clearance

The Grille-Front is an OEM component specifically designed for Whirlpool refrigerator cabinet fronts. It allows for air circulation while protecting internal refrigeration system components. Proper grille functioning keeps components running cool and efficient.  

Symptoms of a bad grille can include:

• Parts of the grille cracking, loosening, or detaching
• Reduced airflow causing elevated temperature readings inside
• Components overheating, leading to premature failures

Causes related to physical impacts, such as kids' toys or vacuum cleaners striking the grille. Direct sun exposure can also cause material degradation over time.

This OEM Whirlpool part is compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This replacement grille covers the appliance's front vent opening to maintain airflow and protect internal components. It restores a clean, finished appearance and secure fit when the original grille is cracked, warped, loose, or missing.

• Directs airflow through the unit for proper ventilation
• Shields internal parts from debris and accidental contact
• Replaces a broken, warped, or missing grille
• Common symptoms include rattling, poor fit, visible cracks, or an exposed opening

• Disconnect power to the appliance before servicing
• Remove mounting screws or release retaining tabs; keep hardware for reuse
• Align the new grille with tabs or slots and secure without overtightening
• Restore power and confirm proper fit and clearance

The Grille is an OEM replacement part for Whirlpool refrigerators. It covers the gap between the bottom of the refrigerator and the floor, providing a clean and finished look to your kitchen. It helps protect the internal parts from dust and debris while also preventing small items from rolling underneath the appliance.

Symptoms of a bad toe grille include:

• Visible cracks or damage
• Discoloration or fading
• Missing pieces or gaps in the grille

A damaged or worn-out toe grille can occur due to regular use, accidental impacts, or general wear and tear over time. If you notice cracks, discoloration, or missing pieces on the toe grille, it may be time to replace it.

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.
 

This 30-inch toe grille restores the finished look at the bottom front of a range or oven while protecting the lower cabinet area from debris. It's a direct-fit exterior trim piece that keeps the appliance appearance clean. What it does:

• Covers and protects the appliance lower front, hiding components and braces.
• Restores a damaged, missing, or dented kickplate to improve the appliance's appearance.
• Helps prevent debris buildup under the appliance and reduces visible gaps.
• Stops rattling or loose trim caused by broken or warped grille pieces.

• High-level replacement: typically installs from the front and secures with clips or screws.
• Disconnect power and move the appliance per the manufacturer instructions before doing any service that requires pulling the unit forward.
• Wear gloves to protect hands and avoid scratching the grille finish during installation.
• Retain or reuse original fasteners when possible; obtain OEM replacement hardware if fasteners are missing.

This is the lower front grille for select appliances. It finishes the base opening and helps channel airflow to the condenser area while protecting components from bumps and debris.

• Covers the lower front opening and provides a clean, finished look
• Helps direct cooling airflow to the condenser compartment
• Shields components from minor impacts and debris
• Common signs it needs replacement: cracked or missing grille, broken mounting tabs, grille won't stay attached, rattling from a loose or damaged panel

• Disconnect power before servicing; use proper PPE
• Remove existing fasteners or release tabs, then pull the old grille straight off
• Align the new grille and secure with the original screws/clips as configured
• Do not overtighten fasteners; ensure even engagement of all tabs