Maytag Guard, Shield, Barrier Parts

This factory shield is a protective panel used within the appliance assembly. It helps guard nearby components and maintain proper operation by directing heat, air, or moisture as designed. Replacing a damaged or missing shield restores correct fit and protection.

• Provides a protective barrier for internal components in the specified area
• Helps manage airflow/heat/moisture path as engineered for the system
• Replace if cracked, warped, missing, or not securing firmly
• Typical signs include visible damage, rubbing/rattling, or evidence of heat/moisture exposure near the shield

• Disconnect power; shut off gas/water if applicable before servicing
• Access the location per your model's service information
• Transfer and reuse original clips/fasteners as needed; do not overtighten
• Verify alignment and clearances before reassembly and testing

Size: 29 1/4 inches x 31 1/4 inches. This universal washer drip tray is large enough for duet washers and sits under the washer to protect your floors from scuffs, spill, etc. Includes a PVC drain fitting.

This lamp cover is the replacement lens that protects and diffuses your oven's interior light, restoring even illumination while keeping the bulb shielded from heat and food residue. It helps maintain safe, usable oven lighting. What it does:

• Protects the oven light bulb from splashes, crumbs and direct contact.
• Diffuses the bulb for more even interior illumination.
• Replaces a cracked, cloudy, melted or missing lens that can cause dim or exposed lighting.
• Fits over the lamp housing to restore the oven's normal light appearance and function.

• Disconnect power to the appliance before starting and allow the oven to cool completely.
• Handle the cover carefully—wear gloves to protect from sharp edges or broken glass.
• Remove any retaining screws or clips, swap the old cover for the new one, then secure the retainer.
• After installation, restore power and replace the bulb if issues persist.

This inlet cover protects and conceals the appliance's inlet area, keeping wiring and connections secure and helping prevent debris from entering. It restores a clean, safe inlet opening and supports proper component alignment. What it does:

• Shields the inlet opening and nearby connections from dust and debris
• Holds inlet components in position to reduce movement and wear
• Helps prevent snagging or accidental contact with inlet wiring or fittings
• Visible damage or a loose/misaligned cover can expose connections and lead to leaks or electrical issues

• One inlet cover

• Disconnect power and shut off water supply before beginning work
• Remove the appropriate access panel or trim to reach the inlet area
• Replace cover, securing with the original screws or clips; do not overtighten
• Inspect nearby gaskets, fittings and wiring while replacing the cover

This replacement sleeve fits over a rotating shaft to reduce friction and protect the mating surface, helping restore smooth operation and reduce noise. Use when a worn sleeve causes rubbing or uneven movement. What it does:

• Acts as a bushing to prevent metal-to-metal contact on a rotating shaft
• Reduces friction and wear on the shaft and surrounding components
• Helps stop rubbing, scraping, or squeaking noises caused by a worn sleeve
• Restores proper alignment for smoother, quieter operation

• Disconnect power (and gas, if applicable) before starting any repair
• Use basic hand tools; no special training required for most installations
• Inspect the shaft and mating surfaces; replace if excessively scored or damaged
• If press-fit, install carefully to avoid damaging the new sleeve; do not use solvents as a substitute for proper fit

This pump sleeve housing is the replacement outer casing that supports and seals the appliance's pump assembly, helping maintain proper water flow and prevent leaks. Fits pump assemblies that use a sleeve-style housing for the impeller and seal. What it does:

• Houses the pump impeller and seals to keep water contained during operation
• Maintains correct alignment between the pump motor and impeller/sleeve
• Prevents leaks that can cause water on the floor or damage to nearby components
• Can reduce pump noise and vibration when cracked or warped housings are replaced

• Disconnect power and turn off water supply before starting any repair
• Remove access panels and disconnect the pump assembly
• Inspect adjoining seals, gaskets, and the impeller; replace any worn components for a reliable repair

A replacement plate used to secure or cover internal components and restore proper fit and protection for your appliance. This stamped metal plate helps keep parts aligned and shields wiring and openings from debris. What it does

• Secures or anchors nearby components to maintain correct alignment and operation
• Covers openings or service areas to protect wiring and insulation from debris
• Helps reduce vibration or rattling by providing a stable mounting surface
• Restores the original enclosure fit and appearance after part removal or repair

• One replacement plate as shown

• Disconnect power to the appliance before beginning any repair
• Installation requires basic hand tools; avoid overtightening fasteners
• Follow OEM instructions for correct placement
• If you encounter damaged fasteners, wiring, or mounting points, address those issues before completing installation