Maytag Housing Or Cover

The Lint Screen Housing is an OEM part for Whirlpool dryers. This part holds the lint screen in place, ensuring that lint is effectively captured during the drying cycle. This housing helps maintain dryer efficiency by preventing lint from entering the exhaust system, which can cause blockages and reduce performance.

Causes of a bad lint screen housing can include frequent use, accidental impacts, or heat-related degradation over time. 

Symptoms of a bad lint screen housing include:

• Difficulty fitting the lint screen securely
• Lint escaping into the dryer drum or exhaust system
• Visible cracks or breaks in the housing
• Reduced drying efficiency and longer drying times

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This ice enclosure is the molded housing for the refrigerator's ice compartment. It supports and protects the ice dispensing components and guides ice into the chute or bin, helping maintain proper alignment and smooth dispensing. What it does:

• Provides structural support for the ice bucket/auger and related dispenser components
• Helps guide ice from the compartment into the chute/bin to reduce spills and jams
• Aids in maintaining alignment and a consistent cold zone around the ice area
• Typical symptoms of failure: cracked/broken housing, ice bin won't seat securely, ice jams or intermittent dispensing, frost/ice buildup in the ice compartment

• One ice enclosure

• Disconnect power; remove the ice bin before service
• Note screw locations; detach the old enclosure and any connected clips or wiring
• Transfer any brackets or hardware from the original enclosure; reuse existing fasteners
• Mount the new enclosure without overtightening; restore power and verify normal dispensing

This ice enclosure is the molded housing that surrounds the icemaker inside the freezer, helping position the assembly and guide airflow for reliable ice production. Replace a cracked or missing cover to restore proper fit and protection around the icemaker.

• Mounts around the freezer icemaker to shield and correctly position the assembly
• Helps direct airflow for consistent ice formation and harvest
• Reduces frost intrusion in the icemaker area
• Common fix for cracked, warped, loose, or missing housing

• Disconnect power and turn off the water supply before service
• Remove the ice bin and icemaker as needed to access the enclosure
• Transfer any clips/brackets from the old part and reuse existing hardware
• Verify icemaker alignment and fill tube clearance before restoring power

This ice enclosure is the molded housing for the refrigerator's ice path. It supports and aligns related components so ice moves properly and helps keep warm air out to reduce frost and moisture around the ice area.

• Provides a rigid mounting point for ice-path components to keep alignment and flow
• Helps maintain an air barrier to minimize frost, sweating, and ice clumping
• Replace if the original housing is cracked, warped, or broken
• Common symptoms include frost or condensation near the ice opening, ice clumps, or poor/jammed ice dispensing

• Disconnect power and shut off water before servicing
• Access the ice area (door or interior access varies by model); retain screws and clips for re-use
• Transfer any guides, seals, or switches from the original enclosure to the new part in the same orientation
• Reassemble, restore power, and check for smooth operation and a good seal

This refrigerator dispenser motor enclosure is the molded housing that mounts and protects the ice dispenser/auger motor inside the freezer door. It keeps the drive aligned and shielded so ice dispensing is smooth and consistent.

• Secures and aligns the dispenser/auger motor behind the ice bin
• Shields the motor and wiring from moisture and debris
• Provides a stable mounting point to reduce vibration and noise
• Damage may present as no or intermittent ice dispensing, loud rattling/grinding, or a loose/misaligned motor assembly

• Disconnect power to the refrigerator before servicing
• Remove the ice bin and dispenser/door trim as needed to access the enclosure; note screw locations and wire routing
• Transfer any brackets, bushings, or seals from the original part if required
• Align the motor shaft/coupler and avoid overtightening screws into plastic; verify dispensing before reassembly

The outlet housing is the molded duct that channels flow out of its assembly and provides a sealed handoff to the next hose or duct. Replacing a cracked or warped housing restores proper sealing, flow, and overall performance. What it does:

• Directs flow from the component to the outlet path
• Maintains a sealed connection to adjoining ducting/hoses to prevent leaks
• Helps preserve proper flow/pressure for efficient operation
• Damage can cause leaks, reduced flow, longer cycles, or unusual noise

• 1 outlet housing

• Disconnect power; if your model uses a water supply, shut it off before servicing
• Refer to your model's diagram for fastener locations and orientation; take photos during disassembly
• Inspect and reinstall/replace any model-specific gaskets, O-rings, or clamps to ensure a proper seal
• After reassembly, run a test cycle to check for leaks or vibrations

This OEM part is a griddle cover made for stoves. A griddle cover is a metal piece that can be placed over the stove's burners to be used as a cooking surface. If a griddle cover becomes damaged due to excessive use, it can become ineffective and need to be replaced. Luckily replacing a griddle cover is a very simple process.To replace the griddle cover, make sure the stove is unplugged. Being by lifting the old cover out of its place by pushing it forward and lifting upward to release it from its attachment on the stove. Once removed set it off to the side. Next, proceed to take the new cover and place it back where the old one was while making sure it locks into its attachment. Once secured, turn the power back on to the appliance.This genuine replacement part is sold individually and is compatible with Whirlpool, Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Sears/Kenmore brand stoves.

This housing is the factory replacement outer cabinet that secures and protects internal components while restoring proper fit and appearance. It's a direct-fit body panel that helps keep parts aligned and shields wiring and controls from damage. What it does:

• Replaces cracked, warped, or damaged outer housing that affects cabinet fit or appearance
• Supports and secures internal components and mounting points for panels and controls
• Protects wiring, switches, and electronics from exposure, debris, and accidental contact
• Helps reduce rattles or misalignment caused by a broken or loose housing

• Disconnect power (and water if applicable) before starting any repair
• Handle edges carefully — metal/plastic edges can be sharp
• Basic hand tools required; alignment and fastener locations must match the original housing

This replacement housing is the main cabinet-style enclosure that supports and protects the appliance's internal components, helping maintain proper alignment and structural integrity. Use it to restore secure mounting and reduce vibration from a damaged or cracked enclosure. What it does:

• Replaces a cracked, broken, or deformed housing that can allow components to shift or rub
• Restores proper alignment for internal assemblies to reduce noise and vibration
• Provides a secure mounting surface for panels, controls, or internal parts
• Helps maintain safe, stable operation by protecting internal wiring and components

• One replacement housing

• Disconnect power and water before starting any repair
• Take photos of the original assembly to aid reassembly; keep fasteners and clips organized
• Use appropriate hand tools; avoid forcing panels—check for hidden clips or screws