Maytag Range Burner & Related Parts

Ordered correct replacement parts (your online form helped to identify correct valves 2 had black dot on inside stem for back small burner 1 had red dot for larger front burner). locked stove, turned off gas, unplugged cord. removed knobs, 5 screws and front plate also removed L shaped plate below knobs for better access to comp. fittings. pulled off ignitior controls loosened compression fittings (hard to get wrench on nut but doable), removed screw holding valve to manifold. reversed order... Read more

Ordered correct replacement parts (your online form helped to identify correct valves 2 had black dot on inside stem for back small burner 1 had red dot for larger front burner). locked stove, turned off gas, unplugged cord. removed knobs, 5 screws and front plate also removed L shaped plate below knobs for better access to comp. fittings. pulled off ignitior controls loosened compression fittings (hard to get wrench on nut but doable), removed screw holding valve to manifold. reversed order... Read more

• Gas smell
• Won't start

I replaced the burner head. I turned off power to the stove, although I did not turn off the gas. I gave the old burner head a slight twist counter-clockwise until it lifted off the stove. I used the pliers to pull the wires from the old burner, then placed them onto the contacts on the new burner. Set it in place, and gave it a clockwise twist until it was snug. This stove originally came with gaskets beneath the burners, but the info for the replacement part stated that a gasket was not... Read more

I replaced the old burner with the new burner assembly which included the ignighter. The screw that held the old ignighter was frozen into the old burner such that just the ignighter could not be replaced. Be care full removing the screws to the burner as they also may be frozen and tend to snap off instead of unscrewing. You will need to drill an tap new holes. Read more

Replace the burner part that was broken. Read more

I replaced the old burner with the new burner assembly which included the ignighter. The screw that held the old ignighter was frozen into the old burner such that just the ignighter could not be replaced. Be care full removing the screws to the burner as they also may be frozen and tend to snap off instead of unscrewing. You will need to drill an tap new holes. Read more

After many years of excellent service the burner I use most often on the top of my JenAir range rusted through. After trying to remove the burner, which was firmly rusted into place, I decided to replace the cooktop pan, both burners and igniters. It was an easy repair to swap out the new parts for the old, and the only tool necessary was a #2 phillips screw driver. The only difficulty was that although the cooktop pan appears symmetrical, the screw hole pattern on each side is different. I did... Read more

This fitting is a 3/8 nut driver and an adjustable wrench. Read more

Replaced burners, saved $350, easy and it worked! Read more

These guys had exactly the parts I needed. We're quite expensive, but they arrived quickly and were a perfect fit! Read more

Ordered caps and self installed. Read more

Ordered new ones. Delivery was very quick. Ordered on Friday, received item on Sunday by 10 with rush order service. Read more

I purchased a burner and a oven orifice replacement kit from Appliance Parts Pros. I downloaded an installation manual from Whirlpool and followed the instructions. It was pretty easy. The front burner orifices could be replaced by just taking off the burner cover. The back ones required removing the burner diffuser. You will need to reattach the back burner bottom assembies after you remove the diffuser before you unscrew the orifice or it might bend the burner piping causing it to not line up... Read more

These are very easy to replace ,just gave the old one a quarter turn lifted it out took the two wires off (noted where each one will go on the new burner ) pop the wires onto the new burner put it on and good to go. Read more

I immediately turned to Appliance Parts Pros and got the best price for 4 new burners and finding parts for my stove top model is a challenge due to its age. My stove top looks new again! Plus, they were delivered ahead of schedule! Thank you!!! Read more

Changing out the stovetop orifices from natural gas to propane- First thing, turn off the gas. On this model stove, there are five burners-two burners in the front, two in the back and one in the middle. The front two burners are different than the other three, they are the largest burners. You can use a 11/32 socket with an extension to go down the middle hole of the burner and screw-out the natural gas orifices. Taking the orifices out was easy. Putting the new orifices in is a different... Read more