Maytag Refrigerator Parts

• Ice maker dispenses too little ice
• Not dispensing water
• Touchpad does not respond
• Leaking

I'm such a pro, I figured I needed a new hose for my water dispenser so I ordered it. When it arrived I called my handyman. He told me I did not need a hose I needed A cartridge. So I had to return the hose and order the cartridge! Your company was so cooperative and made the return so easy Thank you! Next time I call the handyman first! Read more

Ordered new gaskets from Appliance Parts Pros, arrived in 4 days. Removed old gaskets and replaced by starting at top corner and. Pushing seal into slot. Day before, opened seal boxes and spread seals to smooth out. Took about 10 minutes to replace both door seals. Right door magnetic seal improved but not great. Adjusted level and installed a 1/16” washer in door bottom hinge, which leveled door better and improved the seal strength. Read more

My refrigerator was not dispensing ice. I could hear the motor activating but noticed the ice auger was not turning. My old drive shaft was stripped on both ends. Video was very helpful and it was an easy fix for someone with little handyman experience. Received my order much faster than expected! The parts arrived the next day and paid for the standard shipping charge. I live in Texas. Read more

First Problem - WATER INLET VALVE - After having problems with ice maker not making ice, I troubleshot and replaced the water inlet valve. Video and instructions were excellent. With 16 year old fridge, the water lines had compression fittings in the old valve, so had to cut the fittings off with a razor blade to allow the lines to insert into the new valve press-in type fittings. Worked great / no leaks at the new valve. But, new leaks occurred at the water filter housing spraying down into... Read more

Ordered parts from Appliance Parts Pros. Made sure they fit using the model number link. Was a great experience, fast shipping. Read more

After taking the two vegetable drawers out from above, the glass shelf, the pantry drawer and the cross support for the glass, you can get to the two recessed hex head screws holding the end cap. You will need to transfer the metal drawer slide to the new cap, but it doesn't need to come off first. When the end cap is loose, gently rotate it toward the front. Once the humidity control slide is at 90 degrees from the back of the refrigerator, the tab holding it in place will slip out easily.... Read more

• Fridge runs too long
• Noisy
• Freezer section too warm
• Fridge too warm

After reviewing the 'how to' video on AppliancePartsPros.com, I unplugged the refrigerator and removed the back cover to access the motor. I then unplugged the wiring and removed the bad motor. I cut the clip plug and wired it to the new motor, installed the fan blade from the old motor and re-installed the new motor. After connecting the clip plug and re-installing the back cover, I plugged the refrigerator in and checked the interior about 5 minutes after the repair. Everything has been... Read more

• Leaking

Replaced both inlet valves, no joy. Upon further inspection, found ice maker harness extremely tight at lower freezer door hinge, clamped in place right at a pivot point. Essentially the harness is held in place and rotates with the door. 6 wires broken inside. Splice repair and ice maker now works. Most likely will have to replace harness eventually. Unless there is more slack inside the freezer door this will probably happen again. Very poor design. Read more

• Ice maker dispenses too much ice

Ice Door Kit, Control Bracket, and Ice Dispenser Guide were purchased. I followed two videos on replacing the parts. The Control Bracket WP2180226 / AP6005965, was straight forward and I discovered a snapped pin on the old bracket causing an electric switch to be out of place... that repair was easy. When it came to the hinges of the ice chute, I discovered the snap-in, on right side, of the hinge was cracked... this is why the pin escaped. This cracked part is molded into the entire... Read more

Replaced door switch - it took less than 5 minutes - works perfectly Read more

After ordering the part, I first watched the video several times. Then I placed my phone on my workspace so that I could start and stop the video when following the step-by-step instructions. Then I shut down the refrigerator circuit breaker while I removed the ice container and full ice maker components. I then closed the refrigerator doors to keep the cold air in. I kept starting and stopping the video as I went, as I unplugged wiring components, connection jumpers, the ice maker shutoff... Read more

Did some online research and everything pointed to the fact that moisture was getting into the freezer and therefore the seal was not doing it's job. I ran my finger along the seal and sure enough I detected cold air coming out of one corner of the seal. I ordered the appropriate part from Appliance Parts Pros (APP) but decided to test my diagnosis by installing thin weather stripping in the affected area. I checked the freezer the next day and saw no accumulation of any more Rime ice so... Read more

I researched the correct part I needed and ordered it. The part arrived in only 2 days. Installation was easy and the refrigerator is like new again. Read more

• Ice maker not making ice
• Ice maker won't dispense ice

SO I FIGURED THAT ALL THE MECHANICAL PARTS OF IT WERE FINE SO THE LOGICAL THING TO DO WAS TO REPLACE ELECTRICAL COMPONENTS WHICH CONSISTED OF THE THERMOSTAT {THE BRAIN} AND THE CONTROL MODULE WHICH I PURCHASED AT A VERY REASONABLE PRICE . I REASSEMBLED THE UNIT AND IT HAS BEEN WORKING LIKE NEW EVER SINCE. THANK YOU! Read more

• Noisy
• Fridge runs too long
• Fridge too warm
• Freezer section too warm

Unplugged refrigerator and removed access panel from back of fridge. Have had this panel off many times for dust removal. Panel is a cheap piece of glorified cardboard on this Whirlpool model, which is a shame given that it was a $1000 refrigerator. Fan motor is mounted on stamped sheet metal bracket which I removed from cabinet with old fan attached to it. Metal bracket held in place by 4 1/4 inch hex head sheet metal screws. Two outermost screws can be removed with nut driver but access to... Read more

• Not dispensing water

I watched the Appliance Parts Pros repair video and decided to remove the front panel to diagnose the problem. While the repair video is excellent, I could not remove the ice/water dispenser front panel with a putty knife. On my model, 106.56234400, there is no clip that can be released by sliding a putty knife up under the front panel. It took a little effort but I was able to pop the left lower corner clip just by pulling it out with my fingers. Once the cover was off I could see that the... Read more