Maytag Wall Oven Parts

Burner only partially heating or not working? This surface heating element restores even cooking. DIY-friendly repair with photos of wire connections.

Controls gas flow to burners and oven by stabilizing manifold pressure. Replace if cracked, damaged, or leaking to restore proper gas regulation.

Fix a burner stuck on high or won't adjust temperature with this infinite switch. Controls cooktop burner heat levels. DIY repair in under 30 minutes.

This fan motor powers the cooling fan that moves air through your unit. Replacing a worn or noisy motor restores proper airflow to help maintain stable temperatures and reliable performance. What it does:

• Drives the fan blade to circulate air for cooling and temperature control
• Helps prevent component overheating caused by weak or stalled airflow
• Fixes: fan not running or starting intermittently
• Fixes: loud humming, grinding, or rattling from the fan area
• Fixes: longer run times or warm spots due to poor airflow

• Includes: 1 fan motor

• Disconnect power before servicing; allow moving parts to stop
• Note wire positions and motor orientation; take a photo for reference
• Transfer the existing fan blade and mounting hardware as needed
• After install, ensure the fan spins freely and no wiring contacts moving parts before restoring power

Replacement burner cap that fits over the gas burner head to distribute flame evenly. Replace if cracked, chipped, worn, or missing to restore proper appearance.

Burner won't heat or stays cold? This surface heating element restores steady heat to your electric range cooktop. Simple 15-minute DIY repair.

Replace cracked, shattered, or broken outer glass on your range oven door. This front glass panel installs between the door frame and trim pieces.

Burner not heating evenly or taking too long to boil water? This surface heating element restores proper heat output. Moderate DIY repair.

This stainless steel control knob fits on the front panel of the range and is used to adjust the flame on a surface burner. It slides onto the gas valve stem and includes printed markings indicating flame settings. Replace this knob if it is broken, discolored, or no longer turns the valve stem smoothly to control the burner.

Surface burner and electrode assembly for gas ranges and cooktops. Replace when burner is cracked, electrode is broken, or ignition spark is inconsistent.

This stainless steel surface burner knob attaches to the gas valve stem on the range cooktop and allows you to control the flame level of the burner. It features a D-shaped shaft opening and indicator markings for off, low, and high settings. Replace this knob if it is cracked, the markings are worn off, or it no longer grips the valve stem properly, making it difficult to control the burner.

This line fuse protects the appliance's incoming power circuit by opening if an overload or short occurs. Replacing a blown fuse can help restore power once the underlying issue is corrected, preventing further damage to sensitive components.

• Interrupts line voltage when excessive current or a short circuit is detected
• Typical symptoms: unit completely dead, no display or interior lights, won't start or run
• Fuse tests open/no continuity with a multimeter when blown
• A blown fuse often points to another fault that must be addressed

• Disconnect power at the breaker/unplug before servicing; microwaves contain high-voltage parts that can retain a dangerous charge even when unplugged
• Replace only with the same type and rating as the original fuse
• Ensure the fuse seats firmly in its holders; do not bypass or jumper a fuse

Burner won't heat or heats unevenly? This radiant surface element restores quick, responsive heat. Requires lifting cooktop and reconnecting wires.

This upper oven door hinge is a position-specific hinge that supports and controls a side-swing door's movement, helping it open smoothly and seal firmly. Replacing a worn hinge restores proper alignment, closure, and heat retention.

• Provides the pivot and spring action at the door's upper mounting point
• Maintains door alignment for proper gasket contact and heat seal
• Typical symptoms of a failing hinge: door won't close fully, sags, binds/rubs, or pops open
• A poor seal from a worn hinge can lead to heat loss and uneven baking

• Disconnect power and allow the oven to cool completely before service
• Support the door; many models require removing the door to access the hinge
• Install at the factory mounting points and ensure the hinge fully engages the receiver
• After replacement, check door alignment and that the seal contacts evenly

Replace a cracked, clogged, or worn burner head on your gas cooktop. This component directs gas through flame ports for even heating and reliable ignition.

Inner door glass panel for wall ovens and ranges. Replace if cracked, scratched, broken, or missing. Installs between outer door layers for visibility.