Maytag Wall Oven Parts

This surface burner spark electrode creates the arc that lights the gas at the burner. Replacing a worn or cracked electrode restores quick, reliable ignition on your gas cooktop or range.

• Generates a high-voltage spark to ignite the surface burner gas
• Sits beside the burner head and fires when a control knob is turned
• Common symptoms: burner won't light, no/weak/intermittent spark at one burner, visible cracks in the ceramic, arcing to the cooktop
• Helps restore consistent ignition when the original electrode is damaged or contaminated

• Disconnect power and shut off gas; allow the appliance to cool completely
• Remove burner cap and head to access the electrode; access may be from the top or beneath the cooktop per your model's service information
• Transfer any mounting hardware from the old part; route the spark wire as originally and seat the tip at the same gap/position to the burner
• Avoid striking or overtightening the ceramic insulator; keep the tip clean and dry during installation

The Light Bulb is an OEM part for Whirlpool ovens. This bulb is illuminates the oven's interior, allowing you to monitor the cooking process without opening the door and losing heat. 

Causes of a bad light bulb can include regular wear and tear, exposure to high temperatures, or electrical surges.

Symptoms of a bad light bulb include:

• The bulb not lighting up
• Flickering or dim light
• Intermittent lighting issues
• Visible signs of a burnt-out filament

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This electronic control board is the command center for your oven/range. It interprets keypad inputs, switches bake/broil circuits, and regulates temperature via the sensor to restore responsive controls, accurate timing, and consistent heating when the original board fails.

• Receives user input and drives the clock/timer and display
• Controls power to bake and broil relays or igniters based on sensor feedback
• Regulates oven temperature and cycle timing
• Stores/displays fault codes to help diagnose issues
• Typical symptoms: no heat or intermittent heat, unresponsive controls or dead display, erratic temperatures, beeping or error codes

• Disconnect power at the breaker before servicing; verify no voltage is present
• Handle the new board with ESD care; avoid touching circuitry and components
• Move connectors one at a time to matching terminals; reuse existing mounting hardware and panel components as your model requires
• After reassembly, restore power, set the clock, and run a test preheat; for diagnostics or temperature calibration if needed

This foam seal fits between mating parts to create a tight barrier that helps prevent leaks and rattling. Replacing a worn or missing seal restores proper sealing and helps keep your appliance running quietly. What it does:

• Creates a compliant gasket between components to limit air or moisture passage
• Helps dampen vibration and reduce rattling/buzzing where parts meet
• Helps maintain proper airflow or fluid routing as designed
• Typical symptoms include leaks, condensation/frost near a joint, or new vibration noises

• One foam seal

• Disconnect power; turn off the water supply before service
• Note the original seal's routing/orientation before removal
• Clean and dry all mating surfaces; remove old foam and residue
• Install without stretching or over-compressing; ensure even contact with no gaps

This control knob fits the surface burner valve and lets you turn the burner on and adjust flame level. A fresh knob restores clear settings and smooth control when the old one is cracked, stripped, or missing.

• Controls the surface burner's valve for on/off and flame adjustment
• Replaces worn, cracked, or hard-to-read knobs
• Helps when the knob is loose, won't turn the stem, or the indicator is faded
• Direct, slide-on design for the correct valve stem type

• Disconnect power and shut off gas before servicing
• Pull the old knob straight off the valve stem; align and press the new knob on
• Do not force—verify stem shape and orientation for a proper fit
• Test burner operation and ensure the knob turns smoothly and points to the correct markings

The Door Glass is an OEM replacement part for Whirlpool ranges. It provides insulation and protection for the oven cavity and maintains the proper temperature inside the oven while allowing you to visually check on your dishes without opening the door.

Symptoms of a faulty inner door glass include:

• Cracks or shattered glass
• Foggy or discolored appearance
• Heat escaping from the oven

A bad inner door glass can occur due to accidental damage, extreme temperatures, or regular wear and tear. If you notice signs such as cracks, shattered glass, or foggy appearance, it may be time to replace the inner door glass.

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.
 

Color: chrome. It measures about 2 inches in diameter.

Restore steady cooking performance with this surface element coil. The 6-inch, 1250-watt burner replaces a worn or open coil so your range heats properly for everyday simmering, sautéing, and boiling.

• Generates heat on a 6-inch cooking zone for boiling, sautéing, and simmering
• Fixes a burner that won't heat or only heats intermittently
• Addresses uneven heating or unusually slow warm-up
• Helps when the coil shows visible breaks, blistering, or burned spots

• Disconnect power at the breaker and let the cooktop cool completely
• Remove the old coil and inspect the receptacle/terminal block; replace if burnt or loose
• Align prongs and press the new coil fully into the receptacle; ensure the support bracket seats in the drip pan notch
• After installation, test the burner with a pan to ensure even heating

The Top Burner Igniter is an OEM part for Whirlpool gas ranges. This igniter is responsible for generating the spark needed to ignite the gas burner, ensuring efficient and reliable cooking performance. It plays a crucial role in the overall functionality of the stove, enabling the burners to light quickly and safely.

Causes of a bad top burner igniter can include wear and tear from regular use, buildup of food or grease that affects its operation, damage from cleaning, and electrical issues such as power surges or faulty wiring.

Symptoms of a bad top burner igniter include:

• Burners not lighting or taking a long time to ignite
• Weak or no spark visible at the igniter
• Clicking sound without ignition
• Uneven flame or burners not staying lit

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Filter is an OEM part for Whirlpool ranges. Installed at the base of the downdraft vent opening, this filter works to capture grease, smoke and odor particles emitted during cooking.

Causes of a bad filter can include natural saturation over many uses as it accumulates grease residue. Extremely high-heat or splattering cooking methods may also accelerate the clogging process.

Symptoms of an inefficient range downdraft filter include:

• Grease residue visible below the vent opening or on surrounding cabinetry
• Reduced effectiveness at extracting smoke, odors or steam from cooking surfaces
• Vent motor or fan starting to strain or make louder noises during use

This genuine OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This 6-inch radiant surface element is the heating source for a small burner beneath a glass-ceramic cooktop. Replacing a failed element restores reliable, controllable heat to that cooking zone. What it does:

• Heats the 6-inch cooking zone under the glass top when the control is turned on
• Cycles to help maintain the selected temperature during cooking
• Common symptoms of failure: small burner won't heat, heats unevenly or intermittently, or shows visible burn spots/damage

• 1 six-inch radiant surface element

• Disconnect power at the breaker and allow the cooktop to cool completely
• Lift the glass top or remove the cooktop to access the elements; support the glass to avoid stress or cracks
• Note wire positions and transfer connections to the new element one at a time
• Ensure the element sits flat in its mounting brackets before reassembly and testing

This is the electric broil element for your oven. It delivers high, direct heat from the top of the cavity to sear and brown foods, restoring proper broiling performance when the original element has failed.

• Provides radiant heat from the top of the oven during the Broil cycle
• Restores proper searing and browning performance
• Common failure symptoms: no heat on Broil, weak or uneven broiling, element won't glow red, visible blistering or breaks
• Direct replacement for a failed or damaged broil element

• Disconnect power at the breaker or unplug the appliance; allow the oven to cool completely
• Remove oven racks, take out element mounting screws, and gently pull the element forward to access the wires
• Transfer the wires one at a time; ensure terminals are fully seated and do not let wires slip back into the insulation
• Reinstall the element without bending it, tighten screws snugly, restore power, and test the Broil cycle

This burner cap fits over the gas burner head to spread the flame evenly and shield the head from spills. Replacing a worn or missing cap restores proper ignition, consistent flame shape, and a clean, finished look on the cooktop.

• Distributes flame for even heating across the pan
• Helps protect burner head ports from boilovers and debris
• Supports reliable ignition by correctly channeling the flame
• Common symptoms: uneven or yellow flames, slow lighting or no ignition, chipped/warped cap, or a cap that won't sit level

• Allow all burners to cool completely; ensure controls are OFF
• Match the cap to the correct burner size/orientation if your model uses different sizes
• Set the cap centered on the burner head so it sits flush and stable—do not force
• Test the burner and reseat the cap if the flame is uneven or lifts

The Bushing is an OEM replacement part for Whirlpool wall ovens. This component acts as a sleeve to reduce friction and ensure smooth movement in various mechanical parts of the oven, such as door hinges or rotating elements. Properly functioning bushings help maintain the alignment and durability of these parts over time.

Causes of a bad Bushing can include wear and tear from repeated use, lack of lubrication leading to increased friction, or damage caused by misalignment or heavy loads. A failing bushing can lead to inefficient operation or damage to connected components.

Symptoms of a bad Bushing include:

• Squeaking or grinding noises during oven door movement
• Difficulty opening or closing the oven door smoothly
• Misalignment of moving parts

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This is an oven control board and clock for electric ranges. The main purpose of this part is to monitor and control the temperature of the oven and the range. This part also functions as a display for time and temperature settings. This part may need to be replaced if the display is no longer lighting up properly or if any part of the display has burnt out or cracked. The part may also be in need of replacing if it is no longer responding to temperature or time commands. When preparing to replace this part, be sure to first unplug the range or shut off the correct circuit breaker that corresponds to the unit. It is also important to wear work gloves to protect the hands while replacing this part.This oven control board is designed for Jenn-Air, Maytag and Amana appliances. It is an authentic OEM replacement part that is directly sourced from the manufacturer. The control board is sold as a single unit.

This dual-burner surface spark igniter lights two adjacent gas burners on your range or cooktop. Replacing a worn or cracked igniter restores quick, reliable ignition and consistent lighting across the pair, reducing long clicking or failed starts.

• Generates a high-voltage spark at two electrodes to ignite gas at both burners in the pair
• Helps resolve: surface burner won't light, only one of the two lights, intermittent/weak spark, or excessive clicking before ignition
• Often needed when ceramic insulators are cracked, tips are damaged, or the igniter is shorting to ground
• Designed for units that use a shared dual-burner igniter assembly

• Disconnect electrical power and shut off gas before servicing
• Remove grates, burner caps, and bases to access; lift the cooktop or burner deck as required
• Transfer any mounting hardware and align electrodes with burner ports; avoid stressing the ceramic
• Reconnect leads securely, reassemble, and test burner ignition