Maytag Wall Oven Parts

• Door won't close
• Oven not heating evenly

First of all Appliance Parts Pros is the best!! I would not have had the confidence to make this repair myself without their outstanding videos and Q&A sections on their website. And their prices for parts are very competitive. Like many stories on the website, my oven would heat up beyond the temperature set point. When it reached the target temperature, the lower heating element (I think this is the “bake” element) would shutoff, but the top element (“broil” element I believe) would remain on... Read more

• Won't start
• Element will not heat
• Little to no heat when baking

This is for the Whirlpool in-wall double oven GBD307PDS10. No power and the door locked after the shutdown before the self-cleaning cycle was over. I watched some video and this is a known issue the fuses blow during self-cleaning. I opened the door with a 90-degree hook, an easy task. Took doors off (watch video from others), unscrewed from the wall, and made a very small platform. and took the oven out (need two people and take the doors off first. The doors are heavy and you won't lift the... Read more

Replaced switch with back cover off and power plug pulled. The replacement switch was the same as old, was easy to pull off wires and push on new one. Also replaced torn door gasket with new one and was a exact replacement both only took less than a hour. Read more

• Gas igniter glows, but will not light
• Little to no heat when baking
• Won't start

The oven would not heat up but the broiler and stove top burners all worked so I replaced the igniter. The part arrived quicker than I expected - one day with regular shipping - and the repair also went much quicker than expected. After accessing the igniter I was able to unplug the plastic modular connection. Instead of pulling the oven out from the wall - which would have been a huge pain - I was able to reach the plug by removing the bottom storage drawer under the oven. From there it was... Read more

• Little to no heat when baking

The bake (bottom burner) worked after replacing the ignitor. Becareful and do not drop the ignitor or the element will break. I found out the hard way. I bought the first ignitor at a local appliance store. After breaking that one, I found another at appliancepartspros.com for $20 cheaper. Thanks appliancepartspros!!! Read more

• Element will not heat

Followed the instructions that came with the replacement part: made sure stove top was unpowered, unscrewed the old housing from the stove top, cut the wires, stripped some insulation off, attached the new wires with the (accompanying) wire nuts, attached new housing to stove top. Read more

I ordered a replacement part, which arrived in a few days. My husband removed the burned out part and put in the new one. No problems! Read more

Ordered correct replacement parts (your online form helped to identify correct valves 2 had black dot on inside stem for back small burner 1 had red dot for larger front burner). locked stove, turned off gas, unplugged cord. removed knobs, 5 screws and front plate also removed L shaped plate below knobs for better access to comp. fittings. pulled off ignitior controls loosened compression fittings (hard to get wrench on nut but doable), removed screw holding valve to manifold. reversed order... Read more

• Element will not heat

Replaced the Infinite Switch and that solved the problem. Did not need to replace the Surface Element Read more

$4 part and a little time saved $250 if I had had to replace the whole plug-in duel burner unit for our Jenn-Air range. Spade that was replaced fed both burners, other two spades just one. If your burners do not turn on, check the spades before you replace the coils. Read more

• Little to no heat when broiling
• Little to no heat when baking
• Gas igniter glows, but will not light
• Won't start

Replaced the igniter, Simple but there are several points to remember. TURN THE POWER OFF 1) remove the oven door or you will have a hard time reaching the back of the oven. Mine just lifted off. 2) The igniter tip is fragile put a drop cloth over the oven floor in case you drop it even after it is in its holder. 3) The drop cloth will catch screws too if you drop them so they won't fall into the oven. 4) The cable from the oven is very short even after pulling it out from the hole at the back.... Read more

• Gas igniter glows, but will not light
• Won't start
• Element will not heat

After many years of excellent service the burner I use most often on the top of my JenAir range rusted through. After trying to remove the burner, which was firmly rusted into place, I decided to replace the cooktop pan, both burners and igniters. It was an easy repair to swap out the new parts for the old, and the only tool necessary was a #2 phillips screw driver. The only difficulty was that although the cooktop pan appears symmetrical, the screw hole pattern on each side is different. I did... Read more

Replacing the Door Gasket is very easy and will take about 2-3 mins per door. Simply remove the Gasket Retainer (1 screw), and pull off the old Gasket. Install the new gasket by simply pushing the gasket clips into the holes where the old clips came out from. Be sure to start gasket at the first hole either side of the Gasket Retainer and work your way around. Reinstall Gasket retainer. The Door Insulation is a very involved repair, and best to follow specific repair manual instructions. Door... Read more

Replaced It With New One Read more

• Touchpad does not respond

$4 part and a little time saved $250 if I had had to replace the whole plug-in duel burner unit for our Jenn-Air range. Spade that was replaced fed both burners, other two spades just one. If your burners do not turn on, check the spades before you replace the coils. Read more

• No heat

After dismounting the unit from its wall-hanging bracket, the most tedious part of the repair was removing over a dozen screws holding the cover in place from the top, bottom, and both sides. Fortunately, I had placed the unit on a bench that allowed me to slide the unit allowing access to the screws on the bottom edges of the unit. Always discharge the capacitor before continuing to work on the unit by discharging the capacitor by shorting the contact without the diode to ground. Access to the... Read more