Need Help?
Call or text
This injector seal fits the refrigerator's water injector. It restores a tight, watertight/airtight connection where the injector passes through the liner or mates to the fill tube, helping prevent leaks and frost around the opening.
1. Sleeve for input, Injector valve, nozzle and seal for input fixed this problem. Probably the main part that was the trouble was a deformed Injector Valve which is a rubber tube with an internal retention groove at the wide part that grips the Nozzle. The Sleeve and the Nozzle are hard plastic parts that basically looked fine, but I replaced them anyway while I was in there. Additionally I replaced the rubber Seal for Input which seals the plastic input fitting to the tub just to make sure... Read more
Replace your washer's door boot seal when you notice leaks, tears, or mold around the door opening. Creates a watertight barrier. Confirm fit with your model.
Replaced the seal. Read more
Replace worn water inlet valve seals to stop leaks and restore flow. Install when seals are cracked or flattened. Confirm fit with your washer's model number.
Opened the washer (details later) and noted the controls and water path. Ordered dispenser bottom and cover and dispenser valve assembly and rubber washers. When the parts arrived I removed the top portion of the detergent dispenser assembly; removed the door and 2 screws from opposite door wall; snap open the front cover and lifted it off; removed 1 metal screw each from the bottom front corners of the top cover; lifted the top cover and used a piece of wood to hold it up; pull... Read more
Creates a watertight seal between the washer door and tub. Replace if you notice leaks, tears, or mold buildup. Confirm fit with your model number.
Creates a watertight seal between the washer tub and cabinet. Replace if you notice water leaking during wash cycles. Verify fit with your model number.
Disassembled washer, found that 2 out of the 3 basket support legs had cracked through. Unfortunately, support cannot be bought except as an assembly, so had to spend almost $300 for the part. Bearings were worn, but not trashed, so I replaced them and the seal. Note, most parts places (including AppliancePartsPros.com) will only sell the bearings and seal as part of the rear tub assembly. The bearings are standard 6205 and 6206 sealed ball bearings, available from Grainger and many others for... Read more
Hose washer and plastic insert for inlet hose. To order separately: for washer use WPY013783, for strainer use WP22002960.
Here's the story. All my appliances except the dryer broke. Yeah. talk about bad luck. First I tried to fix the refrigerator. Replaced both motherboard and inverter board. Now it wakes up but the compressor does not kick in. Need another part. The washer, well I have to pull out the sink to get enough room to pull out the washer to fix it. Since the refriigerator is still in the middle of the kitchen, I don't need to tear apart another room. Nevertheless, let me say this, I love my "older"... Read more
Rubber gasket that seals the joint between the tub and cover to prevent leaks and water seepage. Replace if you notice leaking or debris buildup. Verify fit.
Ordered boot watched video had no trouble finding ,parts easily entered part num,no problems at all Read more
Seals the washer tub opening to the door, preventing water leaks during wash cycles. Replace if you notice leaking, mold buildup, or tears in the rubber. Verify fit with your washer model number before ordering.
Washer door seal creates a watertight barrier around the door opening. Replace when cracked, torn, or leaking to prevent water damage. Confirm fit by model.
Seals the washer tub to cabinet, preventing leaks and reducing noise. Replace if cracked, torn, or leaking. Verify fit with your model number.
I removed the drum, split it in half and replaced the bearings, seal and tub o-ring. Whirlpool did not offer the bearings without purchasing the back half of the tub for $350.00. I purchased a kit with a new seal for $75.00 and replaced them myself. Read more
Usually ships within 4 - 14 days
Replaces worn or cracked washer door boot seal that creates watertight barrier between tub and door. Prevents leaks from front panel. Confirm fit by model.
Per google and this site, the symptoms of the machine were identical to what was described for a corroded / broken spider. I followed the instructions from this video: https://www.youtube.com/watch?v=iFXp2X99mQs and took apart my machine. It wasn't the exact model, but more than 90% of the instructions and parts were the same. If you've done any type of work on cars (changing brakes, oil change), you should be able to do this without any problems. You'll need a ratchet set, screw drivers,... Read more
Secures water and drain hoses to fittings, preventing leaks at connections. Replace if hoses slip or show water seepage. Confirm fit with your model.
Replace this washer door seal gasket to prevent leaks and maintain proper moisture control. Essential when you notice water escaping or seal damage.