Maytag Washer Terminal Block, Receptacle Parts

Includes screws and wire connectors. For the complete terminal block kit use 279320.

The Wire Harness is an OEM part for Whirlpool washing machines. The wire harness is responsible for transmitting electrical signals that power components and allow them to communicate during each cycle.

Causes of a bad wire harness can be normal wear and tear over time, pinched or cut wires, or wire insulation breakdown due to heat or moisture exposure.

Symptoms of a bad wire harness include:

• Lights or display not working properly
• Washer not starting cycles
• Sensors or switches malfunctioning
• Intermittent operation

This genuine OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This three-circuit connector housing organizes and protects terminals in an appliance wiring harness. It provides a secure, insulated plug connection to help prevent loose contacts, heat damage, and intermittent operation when the original housing is cracked or melted. What it does:

• Holds three wiring terminals in the correct orientation for a mating connector
• Insulates and locks terminals to reduce arcing and overheating at the plug
• Replaces cracked, brittle, or heat-damaged connector housings
• Symptoms can include intermittent power, burnt odor near the connector, discoloration/melting, or a plug that won't stay latched

• 1 three-circuit connector housing

• Disconnect power before servicing the appliance
• Note wire/terminal positions and transfer them one at a time into the new housing
• Inspect terminals; replace any that are discolored, loose, or damaged. Use the correct crimp tool/terminals specified for your model
• Fully seat each terminal until it locks and the connector latch engages securely

This lower wiring harness connects the washer's VMax 2.0 drain pump to the lower control components, restoring reliable electrical connections for proper pump operation and consistent drain cycles. What it does:

• Routes power and signal between the VMax 2.0 drain pump and the washer's lower control assembly.
• Replaces frayed, pinched, or damaged wiring that can cause the pump to run intermittently or not at all.
• Helps resolve symptoms such as no-drain conditions, intermittent pumping, or pump-related error codes.
• Matches original connector ends and routing to fit the factory wiring path.

• Disconnect power to the appliance before attempting any repairs.
• Access the harness by removing the washer's appropriate access panels per the service manual.
• Follow the original wire routing and fully seat all connectors; avoid pinching or stretching the harness.

This lower wire harness routes power and signals between the control and the components beneath the tub on select 4.7/4.8-cu ft top-load washers. Replacing a damaged harness restores reliable connections and helps resolve intermittent motor or pump operation. What it does:

• Distributes power and control signals to lower-cabinet components
• Supports proper operation of the drive motor, drain pump, and related parts
• Typical symptoms: no spin or agitate, won't drain, intermittent operation, or visible heat damage/corroded connectors
• Match by part number for correct fit on 4.7/4.8-cu ft platform models

• 1 lower wire harness assembly

• Disconnect power and water supply before servicing
• Access the underside per your model (tilt the washer or remove panels as required)
• Transfer one connector at a time; route along the factory path and secure with existing clips/ties away from moving parts and sharp edges
• After installation, run a diagnostic or test cycle to normal operation

The Wire Harness is an OEM replacement part for Whirlpool washing machines. It is a crucial component that acts as the electrical wiring system, connecting various components and allowing them to communicate and transfer power effectively.

Symptoms of a bad Wire Harness include:

• Washer not powering on or receiving electricity
• Specific components or functions not working correctly
• Error codes or warning lights displayed on the control panel
• Burning smell or visible signs of electrical damage

Causes of a bad wire harness can include physical damage from impact or pinching, exposure to moisture or water, electrical surges or shorts, and general wear and tear over time. Faulty wiring can lead to connectivity issues and disrupt the proper operation of the washer's systems.

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore washing machine models. 

For mating plug use 691707.

This electrical terminal connects a wire to a matching male/female connector on the appliance, restoring a secure circuit connection and helping prevent intermittent power or signal loss. Use when a damaged or corroded terminal causes poor contact. What it does:

• Provides a secure electrical connection between a wire and the appliance wiring harness or component
• Replaces bent, corroded, or loose terminals that can cause intermittent operation or no power to a component
• Restores reliable contact to prevent arcing and heat buildup at the connection
• Works with compatible wire gauges and mating connectors to maintain circuit continuity

• Disconnect power to the appliance before inspecting or replacing terminals to avoid shock or injury
• Verify wire routing and match the terminal orientation before crimping or installing
• Use proper crimping or soldering techniques and the correct-size terminal for the wire gauge
• Inspect mating connectors and replace any that are damaged or corroded for a long-lasting repair

This fuse holder secures the appliance fuse in place and provides a safe, reliable connection for the fuse that protects electrical circuits. Replacing a damaged holder helps restore proper fuse seating and reliable power flow. What it does:

• Holds and secures the appliance fuse or thermal fuse in its circuit
• Ensures a solid electrical connection to protect against intermittent power or arcing
• Commonly used where a blown or loose fuse causes loss of power, no-start, or intermittent operation
• Restores safe mounting for a new fuse when the original holder is cracked, corroded, or loose

• One fuse holder

• Disconnect power to the appliance before servicing to avoid shock or injury
• Inspect surrounding wiring and terminals; replace any damaged connectors or frayed wires
• Ensure the fuse is correctly rated and seated fully in the holder before restoring power