Maytag Washer Motor

• Pumps but will not spin
• Will not agitate
• Burning smell
• Touchpad does not respond

My whirlpool washer was no longer spinning, so my first stop was YouTube where I found the video from AppliancePartsPros showing how to replace the motor coupling. In addition to the replacement guide, Matt also shows you how to diagnose the problem by looking for rubber shavings under the washer. Seeing the rubber shavings under the washer, combined with the fact that the washer still drained meant that the motor was still working, so something else in the drive train was bad. I took the... Read more

• Burning smell

All's well that ends well, but the getting there was a bit of a pain. The web site suggests 3 possible causes for my problem (incl. the burning smell). I began with the first two since they were inexpensive compared to the motor, which was the third cause (and also the least often cause). There is no way to visibly tell if the motor is bad or not. After replacing the clutch assembly, which did have some plastic pins broken off) and the motor coupling (which actually looked fine, but the... Read more

• Won't start

I removed the belt and found with no load the motor ran but made a grinding noise. I purchased a new motor and installed it. The fix was easy and quick. Read more

I ordered a new motor with a very helpful Chris.It arrived a day later with instructions and was easy to exchange with the old one.I am delighted with how it works and the price was good and the service excellent.thank you. Read more

• Will not agitate
• Burning smell

The washer was on, and I heard a faint humming sound in the laundry room. I went in and opened the washer and it was full of soapy water in the middle of its cycle and was not agitating. I also smelled a faint burning smell. At this point I figured the problem was a bad motor, as the washer is more than 20 years old. I have fixed it twice before, because the first time, the repairman said I should keep this washer going as long as possible. It was made to last with a metal drum, unlike newer... Read more

Unplugged power cord, shut off hot and cold water valves, and disconnected hot and cold water lines. I taped the lid closed and laid washer down on its front panel to access motor parts underneath. Removed center screw (allen wrench) and then removed large, round, plastic rotor (had to use some force with fingers behind it to get it off). I could see that the gear teeth inside the rotor had been partially stripped off ruining the rotor (and causing the noise). I then removed the clutch... Read more

Went to appliance parts pros and typed in the problem, and they had a video on that problem and how to fix it, easy fix, ordered the part, had it 2 days later, took my washer apart while I was waiting for the part to come, and then reviewed the video several times, and then completed my repair, probably saved 150-200 dollars by doing it myself, also had my dryer conk out last year, did the same thing, looked up the problem, ordered the part, and made the repair, the pair is 20 years old, parts... Read more

We watched the videos posted on AppliancePartsPros.com website several times before starting the work. Once we were confident of the process, we jumped in with the complete disassembly of the washing machine's drum rotating assembly...everything that touched the drum or made it rotate. My son and I disassembled and inspected each part for wear/damage and ordered replacement parts based on condition. The parts came in within 3 days of ordering. My son and I took 3 hours to reassemble and... Read more

Once you tilt the washer and prop it against something it's a pretty straight forward and easy fix. If you watch the instructional "How-to" video beforehand, the repair should take between 30 to 60 minutes. It all depends on your skill level and if everything goes smoothly. Make sure you have all the proper tools, grease and blue thread lock at the ready to help you move this repair along faster. This repair was in conjunction with replacing the motor position sensor. I didn't know I needed a... Read more

Installed new motor with a metal pulley from APP and VIOLA! Great service, support and inventory. HIGHLY RECOMMEND! Read more

This was a tricky one to figure out. The Maytag Centennial MVWC400XW4 would fill and wash, then stop before spin cycle or would not complete the spin cycle. We had to manually move the dial to rinse & spin, etc. to get it to finish a load. This technique worked but it definitely became a pain to do and at the time we didn't notice how much longer the machine took calibrating a wash load. I called Sears initially thinking I really didn't want to mess with this and they came out. They... Read more

I changed out the stator. Read more

Started out as a replacement of the coupling between the motor and the basket transmission ( 2 of the 3 legs on the transmission side broken.. )... Bought a new pump, since I would have it off... or so I thought.. Metal output shaft into pump + years of moisture = pump rusted on. Put it all back together - runs fine... for a while.. Then the old pump bearings burn out. Back apart.. Cut the old pump off the motor. Reinstall everything... Nothing, Just sits there and buzzes... Now... Read more

Replaced rotor and stator Read more

Figured out how to diagnose it and found the error codes, all online! learned how disconnect everthing and laid the washer down on its back, saw the 2 malfunctioning pieces, The Drive motor and the shift actuator, removed them and looked up model numbers, found the parts I need here on appliance parts pros and was able to order them and have them delivered in 2 days. Super awesome as it took me maybe 5 minutes attaching everything back to where it went. I ran diagnostics again to see if there... Read more