Maytag Washer Brake & Clutch Parts

Replaced washer drive block and Cam. I called around and finally settled on Appliance Parts Pros because they helped diagnose the problem, told me what parts to replace and had videos to show me how to do it. In completing the repair I had to remove quite a few pieces of hardware in order to get at the part I was to replace. The videos helped but there is a learning curve while you familiarize yourself with the parts and figure out how the remove them. Eventually I got to a large nut that,... Read more

I watched a video on YouTube that showed my exact problem. It had a link to this part AP5665171 Hub and it showed how to fix it. It was a fairly simple fix. I did not even have to remove the tub. I popped the cap on top of the agitator plate (AGP), removed the bolt hold the AGP on. I tapped on the bolt several time to loosen it. Using an angled screw driver, carefully and slowly lifted up the edges of the AGP until I could use my fingers to carefully pull the AGP off the splined drive... Read more

• Spins slowly
• Pumps but will not spin
• Burning smell

A couple of years ago, I had an issue with my Whirlpool washer which is every bit of 18 years old. I checked the internet for what might be wrong and stumbled across some how to videos on how to fix it. So, the other day, when my washer quit spinning the first thing I did is go to the internet again to see if I would be able to fix again. Thank you, Appliance Part pro.com, for your very helpful website with the very informative video's on how to replace parts! After I watched a... Read more

• Noisy

After ignoring for a couple of years that the bearings were bad on our Whirlpool Cabrio washer and just closing the door to the laundry room, it started slinging grease underneath during the spin cycle. Knowing that the cost to call out a repairman would be close to the cost of a new washer, I decided that it would be a nice Saturday project after reviewing AppliancePartsPros’ repair video. The bearing & tub seal kit and bearing installation tool arrived in two days. I’ve done a lot of... Read more

We watched the videos posted on AppliancePartsPros.com website several times before starting the work. Once we were confident of the process, we jumped in with the complete disassembly of the washing machine's drum rotating assembly...everything that touched the drum or made it rotate. My son and I disassembled and inspected each part for wear/damage and ordered replacement parts based on condition. The parts came in within 3 days of ordering. My son and I took 3 hours to reassemble and... Read more

I ordered what I thought were the necessary parts from appliancepartspro.com as my washing machine wouldn't spin. I should have watched there videos before I began as I took the whole cabinet off and everything and after receiving the parts and watching their video realized I didn't need to do so, at that point in time. When I put the pieces back together I found that the tub was really stuck, it would move but for the most part it was hard to move and creating a horrible noise. I knew I... Read more

In reality, this turned into a full-on rebuild project - with several parts orders, not just a simple repair. But I have to give credit: The parts listings with pictures on the AppliancePartsPros web site were really useful in figuring out what was going on inside the machine, and what parts I would need. Also: The repair videos were critical for me to be able to ensure I was reassembling everything correctly. Shout out to Simon, who was featured in several of the repair videos. His "gorgeous... Read more

First I looked at the many you tube vids, and there are many. appliance parts pros pretty much shows you how to deal with the parts. I changed the brake shoes and the clutch assembly which also comes with the driver cam. I also changed the metal brake operating cam. I think that brake lockup or improper brake release was the problem that broke the plastic cam driver. This was the broken plastic part making all the ticking noise. I first changed the coupling on the motor but that wasn't bad. in... Read more

Replaced clutch disc Read more

Actually the 2nd time to replace clutch, first one about 8 years ago. Priced clutch at appliance/repair shop near where I live. Price for part around $235.00 at shop, then I looked at Appliance part pros and same OEM part was around $175.00. Use flat scraper to release the two clips holding the top down, then a nut driver, 5/16 I think, to remove two top clips and front of machine lifts off. Lean machine against wall for bottom access to remove nut holding on clutch. reverse process and your... Read more

Because the washer would stop mid cycle and would start again after some period of time, I presumed that there was something amiss in the drive train (i.e. motor, transmission, belt). Took the unit apart and discovered that two of the three brake pads were destroyed. Motor turned easily as did the transmission. Replaced the brake pads and reassembled. Now the washer doesn't stop as before, but will blow by all cycles never stopping to drain, spin, or rinse. It appears that they damaged... Read more