Microwave Fuse Or Sensor

This thermostat switch is a temperature-sensitive safety device used in select appliances to open or close an electrical circuit at a set temperature. Replacing a failed switch helps restore proper temperature control and protects components from overheating.

• Monitors temperature and changes state (open/closed) at its calibration point
• Helps prevent overheating or incorrect temperature regulation
• Common failure signs: no heat/overheating, intermittent cycling, or unit shutting off prematurely
• May be mounted to a bracket or surface near the heated area, depending on the model

• Disconnect power before servicing; verify no voltage is present
• Note wire positions and orientation of the original switch before removal
• Transfer any mounting hardware from the old part if not reusable
• After installation, test operation and observe initial heating cycle for proper function

The Thermostat is an OEM part for Frigidaire microwaves. This thermostat monitors and regulates the temperature within the microwave, ensuring that it operates within safe limits and prevents overheating.

Causes of a bad thermostat can include wear and tear from regular use, electrical issues, or damage from power surges or overheating events, which can impair its ability to regulate temperature.

Symptoms of a bad Thermostat include:

• The microwave not heating properly
• The microwave shutting off unexpectedly
• The unit not turning on at all
• Overheating or burning smells during operation

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Thermostat is an OEM part for LG microwaves. This part monitors and regulates the temperature within the appliance. The thermostat ensures that the microwave does not overheat, automatically shutting off the power if the internal temperature exceeds safe levels. This preventive measure helps to avoid damage to the microwave and potential safety hazards in the kitchen. 

Causes of a bad thermostat can range from normal wear and tear, which may cause the component to lose its calibration over time, to overheating incidents that permanently damage its sensitivity.

Symptoms of a bad Microwave Thermostat include:

• The microwave unexpectedly turning off during use
• The microwave failing to start
• Inconsistent cooking temperatures or unevenly cooked food

This OEM LG part is also compatible with some Kenmore models.

The Thermostat is an OEM part for GE microwaves. This thermostat maintains safe operating temperatures by monitoring the internal heat levels and regulating the microwave's heating elements.  

Causes of a bad thermostat can include electrical issues, repeated heating cycles leading to wear and tear, or damage from power surges.  

Symptoms of a bad thermostat include:

• The microwave not heating properly
• The microwave shutting off unexpectedly during operation
• Error codes or warning signals related to temperature issues
• The microwave not starting at all

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This line fuse protects the appliance's incoming power circuit by opening if an overload or short occurs. Replacing a blown fuse can help restore power once the underlying issue is corrected, preventing further damage to sensitive components.

• Interrupts line voltage when excessive current or a short circuit is detected
• Typical symptoms: unit completely dead, no display or interior lights, won't start or run
• Fuse tests open/no continuity with a multimeter when blown
• A blown fuse often points to another fault that must be addressed

• Disconnect power at the breaker/unplug before servicing; microwaves contain high-voltage parts that can retain a dangerous charge even when unplugged
• Replace only with the same type and rating as the original fuse
• Ensure the fuse seats firmly in its holders; do not bypass or jumper a fuse

The Microwave Thermostat is an essential component for maintaining the optimal performance of your microwave. This genuine OEM part ensures precise temperature control, allowing your appliance to operate efficiently and safely. Designed specifically for a variety of Samsung microwave models, it guarantees a secure and seamless fit, making installation straightforward for DIY repairs. The thermostat regulates the heating process, preventing overheating and ensuring consistent cooking results every time you use your microwave. By replacing a faulty thermostat with this reliable part, you can restore your microwaveGÇÖs functionality and extend its lifespan without the need for professional service. Its durable construction ensures long-lasting performance, giving you peace of mind and contributing to the overall safety of your kitchen. Whether your microwave is experiencing temperature fluctuations or failing to heat properly, the Microwave Thermostat provides a practical and effective solution. Choose this genuine OEM part to achieve dependable results and enjoy a consistently efficient microwave experience.

This thermal cut-off installs in the bottom location and protects the appliance by interrupting power when excessive heat is detected. It helps prevent overheating-related damage to internal components.

• Monitors temperature at the bottom of the unit and opens the circuit if an over-temperature condition occurs
• Common symptoms include no power, shutting off during use, or not starting after an overheating event
• The TCO tests open (no continuity), it must be replaced

• Disconnect power before servicing; microwaves contain a high-voltage capacitor that must be safely discharged
• Note wire positions and mounting orientation; transfer any reusable bracket/insulator and make secure, insulated connections
• After reassembly, ensure airflow and vents are unobstructed to prevent repeat overheating

This thermostat is a temperature-sensitive switch used in select appliances to regulate heat or provide over-temperature protection. Replacing a failed thermostat restores consistent temperature control and helps protect internal components from heat-related damage.

• Monitors temperature at its mounting point and opens/closes the circuit at a factory-set threshold
• Regulates heating cycles or functions as a high-limit safety cutoff (application-dependent)
• Failure open can cause no heat or premature shutdown
• Failure stuck closed can lead to overheating, erratic temperatures, or extended run times

• Disconnect power and allow the appliance to cool before servicing
• Note wire locations; transfer one lead at a time to the new thermostat
• Mount flush and secure to the mating surface/bracket for accurate sensing; ensure firm terminal connections
• After installation, run and observe an initial cycle to confirm normal operation

This electrical safety fuse opens the circuit when a short or overcurrent occurs. Replacing a blown fuse can help restore power after the root cause is corrected, protecting controls and wiring from further damage.

• Protects the appliance by interrupting power during overcurrent or short-circuit events
• When open/blown, the appliance may be completely unresponsive
• Helps prevent damage to control boards and wiring during faults
• Often fails after a component shorts or a power surge occurs

• Disconnect power to the appliance before servicing
• Use a multimeter to test the fuse for continuity; replace only if open
• Install a fuse with the exact same rating and form factor as the original
• If the new fuse blows again, stop and diagnose the underlying fault; consider service for high-voltage systems

This 250V 15A safety fuse protects the appliance's line circuit from overcurrent. When the original fuse has blown, replacing it can restore power and help safeguard internal components from further damage.

• Opens the circuit if excessive current or a short occurs, protecting internal parts
• Common symptom: unit completely dead—no display, lights, or response to controls
• Blown fuse will test open (no continuity) with a multimeter
• If a new fuse blows again, another component may be shorted and needs diagnosis

• Unplug the appliance before servicing; microwaves can retain a dangerous charge—discharge the high-voltage capacitor
• Access the fuse near the line filter/control area; note clip orientation
• Replace only with the same 250V 15A rating; never bypass or upsize the fuse
• If the replacement fuse blows immediately, stop and troubleshoot the root cause

This microwave thermostat is a temperature-sensitive safety switch that helps protect the unit from overheating. When the preset limit is reached, it interrupts power to the affected circuit to help prevent damage and erratic shutdowns.

• Monitors temperature at its mounting location and opens the circuit if overheating is detected
• Helps protect internal components from excessive heat
• Common symptoms of a failed thermostat include: unit shuts off during cooking, won't start until it cools down, or has no power/no heat due to an open safety
• Replace if the original tests open when it should be closed

• Disconnect power by unplugging the unit or switching off the circuit breaker before servicing
• Microwaves contain a high-voltage capacitor that can retain a dangerous charge; only qualified persons should service and discharge the capacitor
• Note wire locations before removal and transfer connections firmly to the new thermostat
• Mount the thermostat securely and in the same position to ensure proper temperature sensing

Ceramic

This fixed thermostat protects the appliance by opening the circuit when excessive heat is detected. Replacing a failed or weak thermostat restores reliable over-temperature protection and helps prevent heat-related shutdowns.

• Opens the circuit if the protected area overheats to help prevent damage to components
• Helps with symptoms like unexpected shutdowns during operation or no power after overheating
• Can be the cause when the unit only runs again after cooling down
• Helps maintain safe operating temperatures around heat-sensitive parts

• Disconnect power before servicing; some appliances contain high-voltage components
• Access location varies by model; note wire positions before removal and transfer one lead at a time
• Reuse existing mounting hardware; ensure firm terminal connections and correct orientation
• After replacement, confirm proper airflow/venting and normal operation

The Microwave Thermostat is an OEM part for GE Countertop Microwaves. It is a critical component that monitors the microwave's internal temperature to ensure safe operation. 

Causes of a bad thermostat can include failure of internal components due to prolonged heat exposure during cooking cycles over many years of use. Steam and splatters introduced into the microwave from heated foods can also damage sensors.

Symptoms of a bad thermostat include:

• Inability to heat or reheat foods adequately 
• Short cycling of the microwave interior lights 
• Erratic power levels during cook functions
• Overheating errors or shutoffs for safety

This replacement thermostat is also compatible with RCA and some Kenmore countertop microwave models.

The Microwave Fuse Cartridge is an essential component for maintaining the safety and functionality of your microwave. This genuine OEM part is specifically designed to meet Samsung microwave standards, ensuring a reliable and secure fit. By replacing a faulty fuse cartridge with this high-quality part, you can restore your microwaveGÇÖs performance and prevent potential electrical issues. The Microwave Fuse Cartridge effectively safeguards your appliance from power surges and short circuits, providing peace of mind and enhancing the longevity of your microwave. Its easy installation process allows you to quickly get your appliance back in working order without the need for professional assistance. Compatible with a wide range of Samsung microwave models, this genuine OEM part guarantees optimal compatibility and performance. Choosing the Microwave Fuse Cartridge means investing in a durable and trustworthy solution that keeps your kitchen running smoothly and safely.

This temperature control thermostat regulates refrigerator temperature to keep food safely chilled. It replaces a faulty control to restore proper cycling and temperature stability for the fresh food compartment. What it does:

• Senses cabinet temperature and opens/closes the compressor/coolant circuit to maintain set temperature
• Can stop excessive cooling or prevent the compressor from running continuously when failing
• Commonly used when the refrigerator is too warm, too cold, or runs nonstop
• Works with mechanical temperature dials and capillary-sensor assemblies on compatible units

• Disconnect power to the appliance before servicing to avoid shock
• Handle any attached capillary sensor tube gently; avoid kinks or sharp bends
• Verify correct mounting and electrical connections; match terminals to the old thermostat