Parts for Kitchenaid KPM50: 03 - Motor And Control Parts

Secures hinge, lever, or linkage to its bracket on your stand mixer. Replace this screw if stripped, missing, or damaged to restore proper alignment.

Replace your mixer's wavy spring washer to reduce vibration and noise. This washer maintains proper tension between shaft components for smoother operation.

If your mixer speed won't stay set or the lever is cracked, this speed control lever restores precise speed selection. Simple DIY fix in minutes.

Speed control lever cracked or broken? This mixer speed control lever restores speed adjustment. Simple 15-minute repair with basic tools.

Replacement spring for stand mixer control plate assembly. Maintains tension between speed control lever and plate. Needed when broken, missing, or worn.

Fix mixer stuck at one speed or won't turn off. This speed link connects to the speed control mechanism. Common DIY repair, takes 30-45 minutes.

Mixer won't turn off or stuck at one speed? This flat spring restores tension to the speed control mechanism. Common fix for speed link issues.

Replace a lost or damaged thermostat mounting screw to secure your mixer's temperature sensor in position for accurate heat control and consistent performance.

Motor field assembly, 100v, Japan only, should replace motor armature.

Fix a mixer that won't turn on or has burnt electrical smell. This motor field assembly controls variable speed. Replaces worn electrical components.

Mixer won't start or stopped working suddenly? A failed field assembly disrupts the motor's electromagnetic field. Moderate DIY repair restores power.

Replace your stand mixer bowl seal to prevent leaks and ensure proper mixing. Install when you notice liquid escaping or poor bowl fit. Confirm compatibility with your model number before ordering.

Stand mixer bearing supports and centers the rotating drive shaft for smooth, quiet operation. Replace when you hear grinding noises or vibration.

Fix a mixer that won't run, runs slowly, or smells burnt. This motor armature transfers power to attachments. Moderate DIY repair, about 1 hour.

Replacement screw fastener for stand mixers. Secures panels, trim, and brackets to the mixer body. Order when original screws are stripped, missing, or damaged.

If your stand mixer runs only on high speed or won't change speeds properly, a worn governor drive stud may be the cause. This small repair restores smooth speed control in about 30 minutes.

Replace your stand mixer bowl seal to prevent leaks and ensure proper mixing. Install when you notice liquid escaping or poor bowl fit. Confirm compatibility with your model number before ordering.

Seals motor housing to prevent dust and moisture from damaging internal components. Replace if you notice oil leaking or residue buildup. Confirm fit with your mixer model.

Supports moving mechanisms in your stand mixer for smooth operation. Replace if you notice excessive noise, wobbling, or oil leaks. Verify fit with your model.

Supports moving mechanisms in your stand mixer for smooth operation. Replace if you notice excessive noise, wobbling, or oil leaks. Verify fit with your model.

Locking nut for stand mixers. Secures the motor or attachment hub assembly. Replace if stripped, cross-threaded, or missing to restore secure attachment.

Locking nut for stand mixers. Secures the motor or attachment hub assembly. Replace if stripped, cross-threaded, or missing to restore secure attachment.

Mounting screw for washers and dryers. Secures internal components to the cabinet or frame. Replace if screw is stripped, missing, or broken.

Small fitting that seats inside the brush holder assembly to align and secure the motor brush. Replace if cracked, missing, or worn to restore proper brush positioning.

Fix a mixer that won't start or runs weakly. Motor brushes wear from normal use and conduct electricity to power the motor. Basic DIY repair.

Mounting screw for washers. Secures internal components and panels. Replace if stripped, rusted, missing, or damaged during repair or maintenance work.

If your mixer makes excessive noise or vibrates during operation, a worn spring seat cap may be the cause. This part centers and secures springs for smooth, quiet performance.

Fix loose or unresponsive mixer buttons with this cap spring. Restores proper tension and reliable engagement. Simple DIY repair in minutes.

If your mixer runs intermittently or loses power, a cracked or missing brush holder cap may be letting the carbon brush slip. Simple threaded repair.

Fix a mixer that won't start or runs intermittently with this brush holder cap. Secures the carbon brush and spring in the motor assembly.

Fix a mixer stuck at one speed or losing power under load. This speed governor regulates motor performance. Moderate DIY repair with video guide.

Fix a mixer stuck on one speed or operating only at high speed. This speed control plate regulates mixer speed settings. Moderate DIY repair.

If your stand mixer won't turn on or has no power, a damaged power cord is often the cause. This cord restores electrical connection for safe operation.

If your stand mixer won't turn on or has no power, a damaged power cord is often the cause. This cord restores electrical connection for safe operation.

Power cord for stand mixers. Installs at rear of mixer base to supply electrical power. Replace if cord is frayed, cracked, or causing shocks.

Mixer won't turn on? This power cord restores electrical connection to your stand mixer. Common fix for no-power issues. Simple plug replacement.

If your stand mixer won't turn on or powers off intermittently, replace a frayed or damaged power cord. This cord restores safe electrical connection.

Replacement power cord for stand mixers. Connects your mixer to the wall outlet. Replace if frayed, heat-damaged, cracked, or loose for safe operation.

Replace your stand mixer's power cord if it's damaged, frayed, melted, or chewed. This electrical cord connects your mixer to the outlet for power.

Fix a mixer stuck at one speed or running sluggish with this phase control board. Regulates motor power across all speed settings. Video guide included.

Fix a mixer that won't start, runs constantly, or has only one speed. This phase control board regulates motor speed. Easy DIY repair with video guide.

Fix your stand mixer that won't start or runs weak with a new armature. This motor component replacement resolves power loss and operational failures.

Fix a mixer that won't start, slows down, or makes grinding noises. This armature (motor rotor) restores reliable operation when worn or burned.

Fix a mixer that won't run, runs slowly, or smells burnt. This motor armature transfers power to attachments. Moderate DIY repair, about 1 hour.

Protects your mixer shaft from wear and metal-on-metal contact. Replace when you notice rubbing noise or rough operation. Verify fit with your model.

Fastens panels and internal components in stand mixers. Replace if the original screw is missing, stripped, or damaged to restore secure assembly and fit.

Fix intermittent mixer operation or arcing sounds with this brush holder housing. Secures carbon brushes for steady motor contact and consistent speed.

Mixer won't run or just hums? Worn motor brushes in the holder cause power loss. This DIY repair restores full motor function on stand mixers.

If your stand mixer runs at incorrect speeds or won't shift gears properly, this speed disc service tool restores correct drive engagement. Basic repair.

Stand mixer Rotor Slicer, Shredder Attachment for KitchenAid Stand Mixer that includes four stainless steel slicing, shredding cones, and instruction booklet. The slicers include course, thick, think and fine shredder to shred vegetables, fruit and nuts. KitchenAid model number RVS-A

Pack of 2 covers.

Replacement 5-quart polished stainless steel mixing bowl for KitchenAid bowl-lift stand mixers. Installs on lift mechanism with flat handle design.

Pouring shield attaches to the top of your stand mixer bowl to prevent ingredient splatter during mixing. Replace if cracked, broken, or missing.

Lubricates planetary gears in stand mixers. Replace when grease darkens, mixer makes noise, or after gear replacement. Confirm fit with your model.