Parts for Ge PDWT200V00BB: 05 - Motor-Pump Mechanism Parts

Dissolves limescale, mineral deposits, and odor-causing residues from dishwasher tub and spray system. Use monthly to maintain peak cleaning performance.

Fix low spray pressure, growling noises, or leaks from the pump housing. This circulation pump assembly requires basic tools. Takes 1-2 hours to install.

This turbidity sensor monitors wash water clarity so the machine can adjust wash cycles and rinse times for cleaner results and efficient water use. It replaces a failed or inconsistent turbidity reading to restore proper load sensing. What it does:

• Detects soil level/turbidity in wash water so the washer adapts cycle length and rinse actions
• Helps prevent over- or under-washing by feeding water-quality signals to the control board
• Commonly replaces units that cause long or short cycles, poor cleaning, or error codes related to wash sensing

• Disconnect power before replacing to avoid shock or damage to electronics
• Handle the sensor and connectors carefully; avoid contaminating sensing surfaces
• Verify connector orientation and secure mounting; test a short cycle after installation

Rubber grommet cushions and seals dishwasher components. Replaces worn, torn, or missing grommets to restore proper fit and reduce vibration noise.

Fix a dishwasher that won't drain completely with this drain pump assembly. Common causes include worn impeller or blockages. DIY-friendly repair.

Fix a dishwasher that won't drain completely with this drain pump assembly. Common causes include worn impeller or blockages. DIY-friendly repair.

Dishwasher not draining or draining slowly? A worn valve flapper in the dual-pump assembly disrupts water flow. This repair restores proper drainage.

Secures dishwasher hoses to fittings and prevents leaks. Replace if corroded, rusted, or loose to restore a watertight seal. Confirm fit with your model.

Secures hoses to fittings for leak-free operation. Replace when worn or corroded to stop drips on fill, drain, or circulation lines. Confirm fit.

Secures hose connections to prevent leaks in your dishwasher. Replace if water pools under the unit or connections feel loose. Confirm fit with your model.

Replacement hex head screw for dishwasher component mounting. Secures solenoids, valves, and internal parts. Order when original is rusted, stripped, or missing.

This is a hanger mechanism assembly that supports and secures the wash motor inside the dishwasher. It helps stabilize the motor during operation and reduces vibration. Replace this assembly if you notice excessive noise or vibration during the wash cycle, or if the motor mounting has become loose or damaged.

This rubber seal connects the dishwasher's wash pump motor to the tub assembly. Replace if you notice water leaking from beneath the dishwasher or around the pump motor area.

Fix a dishwasher that won't drain or leaves dishes dirty. This impeller and seal kit restores water circulation when the pump is weak or noisy. Moderate DIY.

Fix dishwasher leaking from pump housing with this impeller & seal kit. Repairs worn seals causing water leaks. DIY-friendly, typically 30 minutes.

Dissolves limescale, mineral deposits, and odor-causing residues from dishwasher tub and spray system. Use monthly to maintain peak cleaning performance.

Secures the dishwasher sump connection at the tub base for a leak-resistant seal. Replace if weakened or corroded to stop drips. Confirm fit with model.

Secures dishwasher sump to tub, maintaining seal compression to prevent leaks. Replace if corroded or weak. Confirm fit with your model number.

This is a genuine OEM replacement lower spray arm bearing sourced directly from the manufacturer for use in dishwashers. The lower spray arm spins to distribute water to the dishes during the wash cycle. Thus spray arm bearing supports the spray arm and lessens the friction, which allows it to spin more easily. If the dishes are not clean after the wash and rinse cycle, or the arm is making loud noises, the spin arm bearing may need to be replaced. This bearing is a small metal part that may wear over time. If the bearing is distorted or damaged, the arm will not sit level, and spinning may be very loud, or it may not spin. The spray arm bearing should be replaced. Turn off the breaker or disconnect the power to the dishwasher. Open the dishwasher and pull the bottom rack out. Turn the lower spray arm counterclockwise to remove it. Use a telescoping magnet to pull the bearing up from the hole in the middle. Install the new bearing and reinstall the spray arm. Put the dishrack back inside and reconnect the power.This lower spray arm bearing is a gray metal part that is sold individually. It is designed for use in dishwashers designed by General Electric and Hotpoint.

The Fine Filter Hub Nut is an OEM part for GE dishwashers. It secures the fine filter in place, ensuring that debris and food particles are effectively filtered out during the wash cycle, preventing them from re-entering the dishwasher tub.

Causes of a bad fine filter hub nut can include wear and tear from regular use, damage from over-tightening, or cracking due to impact. A faulty hub nut can lead to improper filtration, causing debris to circulate and potentially clog the dishwasher.

Symptoms of a bad Fine Filter Hub Nut include:

• Poor cleaning results with food particles left on dishes
• Unusual noises during the wash cycle
• The filter becoming loose or not staying in place

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Dishwasher leaking from underneath? A cracked pump connector causes water pooling. Requires dishwasher removal; typically 1-hour repair once accessed.

Sump plate that mounts at the bottom of the dishwasher tub assembly. Replace if cracked, warped, or damaged to restore proper structural support.

Replacement drain hose kit for dishwashers. Flexible tubing routes wastewater from the wash chamber to the pump outlet. Replace if cracked or leaking.

Replaces a broken, cracked, or melted lower spray arm in your dishwasher. Installs on the bottom rack level to rotate and distribute water during wash cycles.

Dishwasher leaking from bottom or not draining? The sump assembly collects and recirculates water. Moderately easy DIY repair from underneath.

Traps food particles during wash cycles to prevent recirculation and ensure spotless dishes. Replace if clogged or damaged. Confirm fit with your model.

This bag and bracket assembly collects lint and debris and secures the disposable bag inside the appliance to maintain airflow and catch particles before they reach the exhaust. Replacing a worn or torn assembly helps restore proper lint capture. What it does:

• Holds a disposable lint bag in place so debris is captured during operation
• Prevents lint from bypassing the bag and clogging the appliance or exhaust
• Restores proper airflow when a damaged or full bag causes reduced performance
• Helps reduce lint buildup that can trigger odors or require frequent cleaning

• Disconnect power to the appliance before service to avoid shock or injury
• Remove the old assembly carefully to avoid spilling lint; wear gloves if needed
• Install the bracket so the bag is oriented and secured per the appliance fitment
• Inspect the surrounding cavity for trapped lint and clean before installing the new assembly

Dissolves limescale, mineral deposits, and odor-causing residues from dishwasher tub and spray system. Use monthly to maintain peak cleaning performance.