Murray Parts

This flat washer is used to attach the idler pulley in a number of small and medium sized gasoline powered engines. These engines include snow blowers, log splitters, riding mowers, lawn tractors, and chippers. Because the idler pulley is subject to a great deal of resistance when the pulley is engaged, eventually the pulley will wear out. Should there be a squealing sound when engaging the drive, the problem is likely the idler pulley. In these cases, the pulley must be replaced. It is a good idea to replace the surrounding hardware when replacing the idler pulley; tNhis includes the flat washer, which is subject to corrosion during heavy use. To replace the idler pulley, first detach the spark plug cap. If on a mower or tractor, drop the mower deck. Remove the original pulley and install in order: replacement pulley, hex bolt, flat washer, flange nut. Apart from dropping the mower deck, the only tools required to complete this installation may be a 9/16 ratchet and combination wrench. This washer is a genuine OEM replacement part, designed to perfectly replicate the original piece. This washer is compatible with Troy-Bilt, Yard Man, Yard Machines, MTD, and Craftsman devices.

Belt keeper rod bracket for lawn tractors. Mounts near the deck to guide and retain drive belts. Replace if bent, broken, or missing to prevent belt slippage.

Steering drag link for front-engine lawn tractors. Connects steering components to control wheel direction. Replace if bent, worn, or damaged.

Flywheel assembly for tillers and outdoor power equipment. Replaces cracked, damaged, or worn flywheels that affect engine timing and cooling fan operation.

This is a ratchet pawl assembly used in the recoil starter mechanism of a string trimmer. It engages the starter pulley to turn the engine over when the pull cord is yanked. Replace this part if the pull cord pulls freely without engaging the engine or if the trimmer fails to start due to a slipping or broken starter pawl.

Blade guard assembly for line trimmers. Protects operator from debris and rotating components. Replace if cracked, broken, or missing for safe operation.

Engine o-ring gasket creates a compression seal between engine components to prevent oil and fluid leaks. Replace when worn or cracked. Verify fit with your model.

O-ring gasket creates a seal to prevent fluid and gas leaks in tillers and lawn equipment. Replace when cracked, brittle, or leaking. Verify fit.

This is a quality rear engine cover that is used on several types of string trimmers. The component is tightened onto the back of the trimer to offer protection and shielding to the engine. It is made of a durable material and comes with both the cover and four screws to attach it to a string trimmer. Over time, the rear engine cover can become damaged, broken, or lost and should be replaced to ensure the engine is protected.Check the rear engine cover for cracks and other damage before installing a new replacement part. First, remove the screws from the rear engine cover so it can be taken off of the string trimmer. An O-ring may be needed to create the proper clearance when installing the new rear engine cover. Make sure to properly tighten the screws on the cover before use.This rear engine cover is an authentic OEM replacement part that is sourced directly from the manufacturer. It is sold as an individual component. The engine cover is designed to be compatible with string trimmers manufactured by Bolens, MTD, Yard Machines, Murray, and Craftsman.

This flywheel assembly mounts on the engine crankshaft of a gas-powered line trimmer and provides the rotational mass needed to keep the engine running smoothly between power strokes. It also drives the ignition system by passing magnets over the ignition coil to generate spark. Replace this flywheel if the engine has no spark, runs erratically, or if the flywheel is cracked, has damaged magnets, or a sheared keyway.

Ignition coil module assembly for gas string trimmers. Mounts to engine block and connects to spark plug. Replace if cracked, damaged, or contacts are worn.

Ignition module for gas leaf blowers and line trimmers. Mounts to the engine to control spark timing. Replace if cracked, damaged, or missing.

Replacement throttle trigger spring for gas line trimmers. Installs inside the throttle trigger assembly. Needed when original spring is broken or missing.