Parts for Electrolux LFMV164QFA: 02 - Oven,Cabinet Parts

Replaces cracked, burned, or missing waveguide cover in your microwave. Protects the magnetron opening from food splatter and moisture damage.

Fix microwave not heating or loud humming noise with this magnetron. Generates electromagnetic waves to cook food. Moderately difficult repair.

Microwave won't start or stopped working during use? A failed thermostat often causes complete shutdown. This temperature switch is replaceable DIY.

This temperature control thermostat regulates refrigerator temperature to keep food safely chilled. It replaces a faulty control to restore proper cycling and temperature stability for the fresh food compartment. What it does:

• Senses cabinet temperature and opens/closes the compressor/coolant circuit to maintain set temperature
• Can stop excessive cooling or prevent the compressor from running continuously when failing
• Commonly used when the refrigerator is too warm, too cold, or runs nonstop
• Works with mechanical temperature dials and capillary-sensor assemblies on compatible units

• Disconnect power to the appliance before servicing to avoid shock
• Handle any attached capillary sensor tube gently; avoid kinks or sharp bends
• Verify correct mounting and electrical connections; match terminals to the old thermostat

Microwave not heating or display not working? This control transformer supplies low-voltage power to electronic components. Moderate DIY repair.

Microwave not heating or making unusual sounds? The high voltage capacitor stores energy for the magnetron. DIY repair with proper discharge safety.

Microwave won't heat? The high-voltage diode converts AC to DC for the magnetron. When it fails, your microwave runs but produces no heat. Moderate repair.

This noise filter is an electronic component that suppresses electromagnetic interference generated by the microwave during operation. It is typically mounted near the power input and helps prevent the microwave from causing static or disruption to nearby electronics. Replace it if the microwave trips a breaker, won't power on, or causes interference with other household devices.

Microwave won't start or is completely dead? This fuse protects against electrical overload. Requires disassembly to access. Often replace with switches.

Replacement light bulb for microwaves. Illuminates the interior and cooktop area. Replace when burned out or dim. Confirm fit with your model number.

Holds the bulb and provides electrical contact for microwave illumination. Replace when heat-damaged, cracked, or bulb won't stay secure. Confirm fit.

Fix a microwave fan that won't shut off or overheating issues with this thermostat. Monitors temperature to prevent damage. Moderate DIY repair.

This is a thermal cut-off thermostat used in the ventilation system of an over-the-range microwave. It monitors the temperature near the exhaust and opens the circuit to shut down the microwave if overheating is detected, protecting internal components from heat damage. Replace this thermostat if your microwave shuts off unexpectedly during use or fails to power on due to a tripped thermal fuse.

Fix an air conditioner that won't start or runs poorly. This compressor start/run capacitor restores motor operation and improves cooling performance.

The Latch Hook is an OEM replacement part for Frigidaire microwaves. It is an internal component that helps securely latch and lock the microwave door during operation. The latch hook works with the door handle mechanism to ensure the door is properly fastened to prevent leaks of microwave energy and for safety. 

Causes of a bad latch hook can include wear and tear over time, damage from repeated use of the door latch, or issues with the latch hook spring or connecting components. 

Symptoms of a bad latch hook include:

• The microwave door not closing or latching securely  
• Difficulty closing or popping open the door during a cycle
• Leaks of microwave energy from around the door seals
• Error codes related to door-latching problems

This OEM Frigidaire replacement part is also compatible with Electrolux, Westinghouse, and Kelvinator microwaves. 

This door release lever connects the push-button to the latch assembly inside the microwave. Replacing a worn lever restores smooth, reliable door opening so the button works on the first press.

• Transfers motion from the door-open button to the latch hooks to release the door
• Helps resolve a door that won't open when the button is pressed
• Addresses a button that feels loose, sticks, or lacks resistance
• Replaces a cracked or broken lever causing intermittent door operation

• Unplug the microwave and discharge the high-voltage capacitor before servicing
• Remove the grille and control panel to access the interlock/latch area
• Note spring and pivot orientation and transfer any reusable hardware
• Test door release action before completing reassembly

Microwave tripping breaker or won't start? A faulty door switch is often the cause. This safety switch detects door position. Moderate DIY repair.

Microwave tripping breaker or won't start? A faulty door switch is often the cause. This safety switch ensures your microwave only runs when the door is closed.

Duct assembly for microwave or microwave/hood combo installations. Replaces damaged, cracked, or missing ductwork. Essential for proper ventilation routing.

Protects and shields your microwave oven light bulb from food and debris while ensuring clear interior illumination. Replace when cracked or discolored.

This is a protective cover that sits over the interior light bulb inside the microwave, shielding it from food splatter and steam. It helps diffuse the light evenly throughout the cooking cavity. Replace this cover if it is cracked, yellowed, melted, or missing, as an exposed bulb can be damaged by moisture and grease buildup.

Grease filter for range hoods and over-the-range microwaves. Dimensions: 5-1/16" x 7-5/8" x 3/32" (5.0625 x 7.625 x 0.09375). Rectangle shape. Captures grease from cooking air. Replace when clogged, discolored, or every 6-12 months.

Replacement wall mounting plate for over-the-range microwaves. Secures microwave to wall studs. Order if original plate is damaged, bent, or missing.

Stainless steel exhaust grille covers and finishes your microwave's vent opening. Replace if cracked, dented, discolored, or missing for a clean look.

Replacement vent grille assembly for microwaves. Covers and protects the front intake opening. Replace if cracked, broken, or missing to restore appearance.

This is a plastic cover that fits over the vent duct opening inside the microwave. It helps direct airflow through the ventilation system and prevents grease or debris from entering the ductwork. Replace this cover if it is cracked, warped, or missing, which can lead to poor ventilation performance or unusual odors during cooking.

Mounting kit secures your microwave to the cabinet or wall with brackets and hardware. Replace if original parts are missing, damaged, or worn.

Keep your microwave's ventilation performing its best. This replacement air filter helps screen cooking vapors before the air is recirculated or exhausted, restoring proper airflow and helping maintain cleaner, more effective ventilation.

• Filters air drawn through the microwave's ventilation system during cooking
• Helps reduce cooking odors and airborne particles in the exhaust stream
• Supports proper airflow and fan performance for effective venting
• Replace when saturated, damaged, or visibly dirty; do not operate without required filters
• Common signs of a spent filter: persistent odors, weaker ventilation, or a discolored/brittle filter

• Disconnect power by unplugging the unit or switching off the circuit breaker before service
• Access the filter from the underside panel or top/front grille, per your model
• Note the old filter's orientation; install the new filter the same way and secure any tabs or screws
• Ensure all panels/grilles are reinstalled securely before restoring power

This Turntable Motor is an OEM part for Frigidaire microwaves. Responsible for the rotation of the microwave's turntable, which ensures even cooking and heating of food. This motor ensures that the turntable operates smoothly and reliably, maintaining the efficiency of your microwave.

A malfunctioning motor can lead to uneven heating or cooking of food, as the turntable is integral to the microwave's ability to distribute heat uniformly.

Symptoms of a faulty turntable motor include:

• The turntable does not rotate when the microwave is in use.
• Intermittent or erratic movement of the turntable.
• Unusual noises coming from the turntable area during operation.
• Food is unevenly cooked or heated, indicating inconsistent turntable motion.
• The microwave operates normally except for the turntable function.

This Frigidaire OEM replacement part is also compatible with Electrolux, Gibson, Kelvinator, and some Kenmore models.
 

Replacement turntable coupler for microwaves. Connects the carousel plate to the motor shaft. Replace if cracked, broken, worn, or missing. Easy DIY.

Support ring installs beneath the microwave turntable to provide stable, balanced rotation. Replace if cracked, broken, or missing for proper use.

Glass turntable tray rotates food for even heating in your microwave. Replace this tray if yours is cracked, chipped, broken, or missing to restore function.

This fan blade mounts to the refrigerator fan motor to move air through the appliance for proper cooling and temperature circulation. Replaces a worn or damaged blade to restore airflow and improve cooling efficiency. What it does:

• Spins on the fan motor to circulate air across the evaporator or condenser coils
• Restores proper airflow when a cracked or broken blade causes reduced cooling
• Helps stop vibration or rattling caused by bent or missing blades
• Can reduce motor strain from an imbalanced or damaged blade

• Disconnect power to the appliance before starting any repair
• Remove access panels and fan shroud to reach the blade; keep track of mounting hardware
• Replace carefully to avoid bending the blade; ensure correct orientation on the motor shaft

This is a vent damper door used in the microwave's exhaust system. It opens to allow steam and cooking fumes to vent outside and closes to prevent outside air from flowing back in. Replace this part if the damper is stuck open or closed, if you hear rattling from the vent area, or if you notice poor ventilation or backdrafts during cooking.

Controls airflow through your microwave's ventilation system. Installs at exhaust opening to prevent air backflow. Replace if cracked, missing, or damaged.

Replacement waveguide cover for microwaves. Protects the magnetron antenna from food splatter and grease. Replace if cracked, burned, or missing.

Spacer component for microwave installation. Provides proper clearance and support between mounting surfaces. Replace if cracked, broken, or missing.

This mounting nut kit secures a threaded connection or component inside your appliance, keeping it tight and stable during operation. Replacing a worn or stripped nut restores a solid hold and helps prevent leaks, rattling, and poor performance. What it does:

• Fastens a component or fitting to its mating surface, maintaining proper alignment
• Restores grip when original threads are stripped, cracked, or worn
• Helps prevent vibration-related loosening during cycles
• Can resolve symptoms such as a loose/wobbly assembly, rattling noises, seepage at the joint, or visible thread damage

• One mounting nut kit

• Disconnect power; shut off water supply if the joint carries water
• Support the mating component while installing to avoid strain on plastic parts
• Start threads by hand to prevent cross-threading; tighten only until snug—do not overtighten
• Inspect any related gasket/O-ring and replace if worn or damaged