Lg Washer WM2240CS Parts

REMOVED BACK PANEL, USED PLYERS TO REMOVE CLAMP, PULLED OLD HOSE OFF, REVERSED PROCEDURE TO INSTALL NEW HOSE. TOTAL TIME ABOUT 10 MINUTES. Read more

I figured after 10.5 years that it might be time to replace the dispenser hoses because I was noticing black stuff in the dispenser trays. I replaced two or the four hoses and clamps on the far left side and for good measure the hot water inlet valve. The inlet valve was okay but the screen had all kinds of crap in there that I couldn't clean out so now I have an extra solenoid just in case one of the others fails. While I was at it I removed the dispenser and cleaned the calcium build up on... Read more

Our 10-year-old LG WM2487HWMA front load washer had gradually developed multiple problems. It sounded like a jet engine during high speed spin, both the drain pump and circulation pumps were noisy, it would not drain properly (water was coming in during spin cycle), no water was spraying out at the top of the door into the drum like it is supposed to when the circulation pump was running. It's amazing we had still been able to wash clothes at all! With the help of the excellent... Read more

Took top off and did a line at a time Read more

I suspected the tub gears where ready to break so I dismantled my LG WM2032HW front load washer. I found the spyder gear corroded and broken. I also found that the stainless steel drum abraded the front tub cover so bad, it was cracked. My washer is an early model and always had standing water in the door seal after a wash. What I learned is LG stopped making the orginal front tub cover and replaced it with one that had a drain hole at the bottom front edge. I also learned that this new... Read more

The error code was E0 and this indicated that there was a drainage issue with the washer. I bought a new drain pump motor and a front seal gasket from Appliance parts pros, watched the installation video and installed the parts. The video was direct and straight forward. Everything is working very well again Read more

I figured after 10.5 years that it might be time to replace the dispenser hoses because I was noticing black stuff in the dispenser trays. I replaced two or the four hoses and clamps on the far left side and for good measure the hot water inlet valve. The inlet valve was okay but the screen had all kinds of crap in there that I couldn't clean out so now I have an extra solenoid just in case one of the others fails. While I was at it I removed the dispenser and cleaned the calcium build up on... Read more

Can't buy LG parts in Canada without getting an LG Tech to install. $1000 repair was too steep for me so went on websites and bought from Appliance Parts. Watch the video on Appliance Parts. Note - Joyce from Appliance Parts really helped in identifying the bolts that I needed. Read on and you will see why. Stripped down machine and identified the spider had failed along its three arms. Bearings were still in good condition. Managed to get three bolts off spider but remaining three had same... Read more

After watching the video carefully and taking notes for step-by-step dismantling of the LG washer, I took it apart methodically placing each item on a table in the order removed. I was able to remove and replace the bearings with no problems following the tips and tricks. The spider did not seem to be in bad shape but since I had a new one, it seemed reasonable to replace it as well, but it was difficult to extract the old one from the drum. The bolts are assembled with weld glue, so it is a... Read more

My problem was a broken spider. I followed your excellent video, but have some additional input that should be incorporated in a new video showing the required upgrade procedures and parts required to repair an early model with damaged front tub half using currently available parts. Don't expect everything to go as easy as the video. 1) Used 4lb. brass hammer to drive shaft from bearings. 2) Torqued spider bolts to 20ft lbs. with thread locking compound. 3) attached rubber seal to front tub... Read more

I originally thought the washer had a bad bearing, but once I got it disassembled it the spider arms were broken. This required the replacement of the tub assembly. While replacing the tub I replaced all of the water bellows. The parts came quickly, the live chat and videos were very helpful. This washer has to be completely disassembled to replace the drum, so mark all the screw locations, tag and bag everything and take lots of pics. It was a very rewarding project and hundreds of dollars... Read more

I started by watching the video and it was very helpful. I would make one suggestion. On our model the weights on the tub sit very close to the front gasket. It is much easier to put the gasket on the tub before you put the weights on. Also, since the washer was tore apart, I replaced the hoses and seals and shocks since the machine is about 8 years old. The shocks made a huge difference. It spins like it did when it was new. Thanks for the video, it was very helpful. Read more

The upper counter-balance weight mount design is a poor design to begin with. It started to rattle loose approximately 5yrs into the 8yrs that we've owned it. As it would start to loosen up (as evidenced by the loud banging noise exhibited during operation); I'd shut it down, pull the top off, remove the weight (it was almost always half rattled off at this point), wrap the mount lugs with friction tape (the plastic lugs were being worn down/chaffed by the balance weight), put the weight back... Read more

Replacement Read more

Following what I've seen or watched from you tube video clinic "how to replace drain pump for LG Washer, model wm2277hw and the help that I received from representative/ customer service of appliacepartspros, I fixed our LG Washer no problem. I am very much thankful to the representative of AppliacePartsPros who help me analyzed the problem and recommended the right parts that I needed and most importantly arrived 2 days as ordered. I would recommend AppliacePartsPros for ordering your parts. Read more