Samsung Refrigerator RFG296HDRSXAA Parts

The Samsung french door freezer has a handle that has plastic pivot plates that help "push" the door open during its first inch or so of travel. One morning, the handle pulled off taking portions of both pivot plates with it! The parts from AppliancePros arrived very quickly, and the repair required re-positioning the mounting holes, even thought the replacement parts looked identical to what was left of the pivot plates. Okay, that‘s not AppliancePros fault in any way whatsoever; this happens... Read more

I removed the door and the hinge assembly from the right side; it turns out the grommet had never been installed and this is what was causing the door to grind down the metal hinge. It was remarkably easy to replace and my door is working perfectly! Read more

Samsung does not make it easy to replace the casters. The shafts holding the casters are crimped at the ends and had to be cut off with little room for any tools. I had to jack up the fridge and I used a hacksaw blade with a handle to cut through the wheel shafts. I didn't want to use a reciprocating saw. I couldn't find a way to crimp the new shafts so I drilled small holes at the ends and used cotter pins to retain the shafts in place.The rear caster had no room to slide the new one in... Read more

I started by replacing the water filter assembly since it was leaking after I attempted to install a non-name-brand filter. The new assembly didn't fix the problem (but was hard to find, and AppliancePartsPros was amazing in being able to get one). Further, while replacing that I noticed that the previous owner had literally cut out the grounding pin from the power cord. I decided to replace the power cord and the Ice Maker Assembly. None of the online stores seemed to have either part listed... Read more

I replaced the control board and the microswitch. Read more

The Samsung french door freezer has a handle that has plastic pivot plates that help "push" the door open during its first inch or so of travel. One morning, the handle pulled off taking portions of both pivot plates with it! The parts from AppliancePros arrived very quickly, and the repair required re-positioning the mounting holes, even thought the replacement parts looked identical to what was left of the pivot plates. Okay, that‘s not AppliancePros fault in any way whatsoever; this happens... Read more

Order a new fixer Read more

Samsung does not make it easy to replace the casters. The shafts holding the casters are crimped at the ends and had to be cut off with little room for any tools. I had to jack up the fridge and I used a hacksaw blade with a handle to cut through the wheel shafts. I didn't want to use a reciprocating saw. I couldn't find a way to crimp the new shafts so I drilled small holes at the ends and used cotter pins to retain the shafts in place.The rear caster had no room to slide the new one in... Read more

I looked at the blow up drawing to figure out what parts I might need. I then watched a you tube video to see how to take the handle off. I kind of figured out on my own how to remove the ruined cap handle. It took me a few minutes to figure it out and more time to remove both the handle and the broken part. Turns out I did not need the spring nor the shaft cap handle. Very proud of myself. Saved a huge amount of money. Only problem was that I could only put in one screw as the previous... Read more

• Fridge too cold
• Fridge too warm

Replaced sensors and heater element. We'll see if that fixes the problem. It usually happens every 3 months. Read more

In order it SHOULD be done: Pried off two white caps covering the screws that attach the flap to the left door, then removed screws. Lifted flap up to remove from door and disconnected cable. Used a thin blade to pry out the inner cover of the flap, then carefully pried out the insulation piece inside. Loosened the screw holding the center cap from the inside and removed cap. Worked the cable out of the hinge piece so it could be removed and cable pulled through case. Pried upper and lower caps... Read more

Removed the bottom shelf by releasing the 2 clips near the water filter, then lifted the front of the shelf and slid it out. Removed 2 screws from the broken Vegetable Rail and replaced it with the new one. Slid the shelf back into place and locked it down into the clips. Done. Took longer to remove everything from the shelf than it did to fix it. Less than 5 minute repair. Read more

Simply removed one screw pulled dispenser control panel straight forward disengaged electrical connection and reassembled. Literally was a 3 minute job. Read more

I removed the broken rail saving the 2 Phillips head screws for installation of new drawer rail. Removal of the shelf above the drawers was required and was accomplished by pushing a button on the front of the shelf support. The installation was a snap and took about 10 minutes after removal of food items. The part was the correct one as verified by the model number on the inside of the refrigerator door. Thanks AppliancePartsPros.com! Read more

The start button had been tricky to use. You had to push it in just a certain way to get the dryer to start. Eventually it was non-responsive. All other controls worked and there was no error code displayed. The repair was to replace the whole control board which cost around $100. Heavy sigh.. Be sure to keep track of all your screws. BTW it was not the thermal fuse. All the online videos say this is the first thing to look for when the dryer will not start. Be sure to check with the person... Read more

I watched the videos and bought the parts I needed then replaced them Read more