Samsung Washer WF42H5000AWA2 Parts

Needed to replace washer counter balance. Also order shock absorbers in case they needed to be replaced, fortunately they didn't need replacement and will be returned. I used Appliance Parts Pros many time and always found them to be very helpful and the repair videos are very helpful. Read more

I replaced the main PCB in the back bottom of the washer. Simple exchange of pcb. All I needed was a phillips screwdriver and a second set of hands while all the cabling was moved from the original main pcb to the replacement pcb. Washer works like a charm now. Read more

Completely broke down washer and replaced part using the instructional video. Everything worked. We are still catching up on laundry. It's running like a champ now. Read more

Replaced drum bearings. Replaced front shocks, one had hardly any resistance. Replace both door boot clamps. Always take pictures as you take apart ! Learned the hard way years ago ! Read more

Followed the excellent videos provided by AppliancePartsPros. Made a multi step repair, if not simple, then extremely less complicated. Loved the way they showed the step by step disassembly as well as the step by step reassembly. Great videos. Got the right parts the first time and very fast delivery. Can’t say enough good things about AppliancePartsPros.com Read more

With all the bouncing around the shocks appeared to be done in but that was not the issue. The key was the balance ring. It had leaked all the fluid out causing all the beads to clump. This caused the drum to wobble wildly and not spin at speed. Getting to the ring to replace it is not a trivial task and took me several hours. Would have been much easier with help as the drum is quite heavy. The on-line video's are very handy and should be watched before attempting this job to save you a... Read more

This is an easy fix. Just remove the back panel, remove the hose clamp to pull out the old hose, put the new hose on, make sure the clamp is well centered onto the connection, and return the back panel. Make sure to insert the drain hose into the three plastic guides that prevent the hose from moving around. The Samsung factory did not do this on my original hose, which is why it failed, because it was rubbing against the tub support and it wore a hole into the hose. I am going to complain... Read more

First I took off the spring loaded wire ring holding down the seal to the door with needle nose pliers. Pulled back the seal. Removed the 3 screws holding the part on the front of the washing machine. Slid the piece out. Took the protector guard off the off piece and unplug the wires. Put the wires into new part. Put the protector on the new part. Slid the part back into place. Screwed it back in. Put the seal back on. Put the wire spring loaded ring back around the seal. Total time 15 minutes... Read more

Removed top panel to reach the hose and sensor. Propped the washer back, reached up to remove bottom hose assembly. Replaced with new hose and new sensor. Put top panel back on. Parts place told me the part was backordered for months and repair would cost at least $80. Got it in three days and fixed it myself. Read more

I first check the schematics to find the heat sensor. On my model it's c on the control panel. I checked the continuity on the orange and white wires. It showed some continuity but not much. I then went to the heater element and found the orange and white wires going to the thermistor. Turns out the heater element and thermistor need repalced. Read more

Ordered part by looking at parts diagram and followed You tube instructions. Easy and quick! Read more

Washer said error no drain. Cleaned the filter and still no drain. So the next step was to check the hose for any debris and when I went to pull the hose off it broke, at the same time I found the check valve flap broke in the drain pump and it was blocking the hose. So I replaced the check valve on the drain pump and replaced the hose. Read more

We are moving soon. In checking, I found that a front loading washing machine tub must be stabilized using shipping bolts. I found the correct items on line at AppliancePartsPros.com. "Chris" of your staff was very helpful. He informed me that my washer required only 3 shipping bolt assemblies, instead of the four I expected to buy. The bolts were delivered two days after my order. Read more

New user interface board and control board. The most difficult part was unstacking the drier. There are youtube videos that show how to replace these motherboards. Read more

• Will not agitate
• won't spin

Actually, I am returning your parts. THERE IS NOTHING WRONG WITH THEM! My wife actually found out that we had a warranty on our washer that we didn't know about. But, I can comment that I did chat with your customer service and you guys were very helpful. Read more