Samsung Washer WF461ASP Parts

With the video that was made from appliance pro.Help me out one hundred percent to understand what I was dealing with Read more

• Shakes and moves

My washing machine was making a loud thumping sound and bouncing around a bit. Research suggested that it could be bearings and/or the spider shaft assembly. After watching the instruction videos to replace the spider or bearings, I seen you need to replace both the shaft seal and tub gasket to get to the spider and bearings. So I ordered both and waited for them to arrive. Plan was to disassemble the washer, determine what was needed, order the additional parts needed, and reassemble after the... Read more

I followed Matt's awesome video from AppliancePartsPros.com to build up my "I can do this" reserves. But here's the story leading up to that point... We purchased our Samsung WF419 on a “Black Friday” special November 2009 expecting to get some good years out of the washer/dryer pair. We don’t run more than 2 or 3 loads a week in the washer, so ours has had relatively little use over the beginning of its anticipated and expected long life-cycle. When the “thumping” started on the spin cycle a... Read more

I followed Matt's awesome video from AppliancePartsPros.com to build up my "I can do this" reserves. But here's the story leading up to that point... We purchased our Samsung WF419 on a “Black Friday” special November 2009 expecting to get some good years out of the washer/dryer pair. We don’t run more than 2 or 3 loads a week in the washer, so ours has had relatively little use over the beginning of its anticipated and expected long life-cycle. When the “thumping” started on the spin cycle a... Read more

Normally, I hire someone to come fix washer or dryer problems as time is limited and if the cost is close or more than the machine, I buy a new one instead. But since we are on shelter-in-place, I figure I could repair it since I have more time on my hands and my brother assured me, it was not hard to do. I took the top panel, door off and then looked online to find a service manual, which allowed me to take the front panel off. My suspected drain hose was the failure mode: the rubber tube... Read more

• Noisy
• Leaks water

Replaced drain pump. Your video on your web site was very helpful. Read more

• Will not agitate
• won't spin

My washer would not spin. This fixed my problem only took me 5 minutes to uninstall and install. Read more

I took apart the washer to find both of the weight balancers had broken in 2 and were banging around. They had also caused the boot seal to rip. I removed the broken weight balancers and replaced them along with a new boot seal. There was one small spot with the seal wasn't fully attached to the outer drum so I had to take it back apart to fix that minor error on my part. Otherwise, it was a fairly easy fix. Read more

I watched the you tube video that completely explained how to do it. It was very easy to do. Read more

Ordered a new knob and took out little bits of the old one. Took the new knob and pressed it over the stump and presto works like new. Read more

Normally, I hire someone to come fix washer or dryer problems as time is limited and if the cost is close or more than the machine, I buy a new one instead. But since we are on shelter-in-place, I figure I could repair it since I have more time on my hands and my brother assured me, it was not hard to do. I took the top panel, door off and then looked online to find a service manual, which allowed me to take the front panel off. My suspected drain hose was the failure mode: the rubber tube... Read more

With all the bouncing around the shocks appeared to be done in but that was not the issue. The key was the balance ring. It had leaked all the fluid out causing all the beads to clump. This caused the drum to wobble wildly and not spin at speed. Getting to the ring to replace it is not a trivial task and took me several hours. Would have been much easier with help as the drum is quite heavy. The on-line video's are very handy and should be watched before attempting this job to save you a... Read more

The Cold Water Inlet Valve had a very good You Tube Video and I followed it. One note of caution, as I chuckled at the guy on the video saying watch for sharp edges, he was correct. When removing one of the lines from the valve, my pliers slipped and my elbow hit the front of the machine(inside edge) and cut my elbow. So after that I draped the edges with towels to avoid that happening. Again the fix was easy and very straight forward from the video. No extra pearls of wisdom here. Total... Read more

I first check the schematics to find the heat sensor. On my model it's c on the control panel. I checked the continuity on the orange and white wires. It showed some continuity but not much. I then went to the heater element and found the orange and white wires going to the thermistor. Turns out the heater element and thermistor need repalced. Read more

Ordered part by looking at parts diagram and followed You tube instructions. Easy and quick! Read more

When I opened the rear cover and check the temperature sensor, I noticed the wire connection was damp. I dried it up with a hair dryer and it worked again for a few days. Then the problem came back. When I gone back to inspect the second time, i noticed a lot of water on the floor. I knew there was a leak. I followed the disassemble samsung washer video from "Repair clinic.com" to open the top cover, then i realized the assembly hose was busted. I ordered the parts from this site and... Read more