Poulan Parts

This is a replacement chainsaw retaining ring. The sprocket is commonly attached to the gear drive shaft in chainsaws with a retaining ring. If the original retaining ring becomes damaged, the chainsaw will not operate properly.Needle-nose, snap ring, or retaining ring pliers may be required to remove the old, damaged retaining ring. To install the new retaining ring, snap ring or needle-nose pliers should be placed into the small holes located on the new retaining ring. Then, slightly open the pliers to pull back the retaining ring's arms, opening up the ring center. Careful attention should be paid while opening the retaining ring to avoid overstretching. Overstretching the retaining ring would lead to the sprocket not correctly attaching to the chainsaw's gear drive shaft. Finally, with proper sizing, the retaining ring can be placed over the wheel grove, attaching the sprocket to the drive shaft.This retaining ring is an OEM part that is sourced directly from the manufacturer. This retaining ring is designed to replace damaged rings in Poulan, Poulan Pro, Husqvarna, and Craftsman chainsaws. The retaining ring is sold individually.

Carburetors mix fuel with air to ensure the engine gets just the right amount of combustion. It works when idling and when in operation, and a chainsaw carburetor requires an adapter. This reduces vibration to the carb and isolates heat to help keep the carburetor cool. This carb adapter kit will connect the carburetor to the cylinder and uses a gasket on either side that can fail and require replacement. Because plastic can be used for a carb adapter, it can crack and lead to failure. This OEM carb adapter kit is meant for Craftsman, Poulan and Husqvarna chainsaws, and will work in many different models. Replacing it will require the use of a wrench set, socket set, pliers, and screwdriver. As noted, gaskets may also be needed, but this part is sold individually and includes only the chainsaw carb adapter.

This is a chain bracket ensures the chain on the equipment remains attached and stable when the lawn tool is being used. This chain bracket is made of durable materials but over time, it can wear out or experience damage. If there is substantial damage or the chain bracket has broken, it will need to be replaced.If a replacement is needed, work gloves and a wrench set will be needed. Make sure the chainsaw is powered off and the spark plug wire has been removed from the equipment. The clutch itself will first need to be removed to get access to the chain bracket. Remove the old chain bracket using a wrench and take the new bracket and place it in the same location. The chain will interlock with it. Make sure it is tightened properly before putting the spark plug wire back on.This is a genuine OEM replacement chain bracket that is directly sourced from the manufacturer. It is sold as an individual component. The chain bracket is designed to be used with chainsaws and string trimmers manufactured by Poulan, Poulan Pro, and Craftsman.

The clutch assembly is located in the clutch drum and connected to the drive shaft of the motor. This part is what allows the engine to idle without actually driving the cutter on lawn and garden equipment. The clutch is constantly engaged, so it can wear out over time and eventually need to be replaced. It may also become damaged in a direct impact or incident. If the clutch assembly fails, this could impact the ability of the engine to idle properly or even to remain running once it's started. This replacement part can offer an exact fit for compatible engines. This OEM clutch assembly is manufactured to high standards by Poulan and is designed to be compatible with various machines from Poulan, Weed Eater, Jonsered, and Husqvarna. The clutch assembly is a replacement part for various trimmers and pruners from the brands listed above. Replacing the clutch will require a wrench, screwdriver, pliers, and socket set. Be sure to cool the engine completely and wear gloves when doing repairs on lawn and garden equipment for safety.

This is an OEM replacement chainsaw bar plate for select brands and models of chainsaws. The chainsaw bar plate is responsible for holding the chainsaw guide bar in place and providing a secure foundation to reduce vibrations, while also spacing the bar from the chassis. The plate itself can become loose over time, or can even become damaged and lead to things like oil leaks from a loose chain. If the bar plate is in disrepair or not functioning correctly, it should be replaced immediately. this genuine replacement part can provide an exact fit for compatible saws. This OEM bar plate is manufactured by Poulan and will fit a number of chainsaws from the brand Craftsman, as well as those from Husqvarna and Jonsered. This durable part is made from high-quality metal and can be replaced with only a few tools. The plate is sold individually as a single unit. Hardware is not included and will have to be purchased separately if it is required. Always wear gloves and disconnect the spark plug before beginning repairs on chainsaws.

This part can be used to replace a deteriorating or leaking oil pick-up in chainsaws. An oil pick-up is essential for a smooth-running piece of equipment, as it supplies oil to the engine. Over time, oil pick-ups can become worn, which can cause leaks and prevent the engine from receiving the necessary supply of oil to operate properly. This part is manufactured from high-quality, durable plastic and non-corrosive metal. This assembly pick-up oil tank is a genuine OEM replacement part that has been sourced directly from the manufacturer. This replacement assembly pick-up oil tank fits various different models of Husqvarna and Poulan chainsaws. Please note this part is sold individually.

This gasket kit features replacement gaskets for use in a range of gas-powered handheld lawn and garden machines. The kit includes a range of O-rings, seals, and gaskets used as a means to provide tight seals between elements of the engine to prevent leaks from air, fuel, oil, and so forth. Even durable gaskets such as those found in engines will start to wear down over time. They can start to crack and break, and sometimes they will shrink. When this happens, they no longer provide a tight seal and will need to be replaced. It is recommended that the gaskets and seals are replaced whenever the owner is servicing their small engine. This will ensure a proper seal when the engine is reassembled. This gasket kit has genuine OEM parts to ensure a proper fit and a tight seal. The kit is sold individually and works with many models of string trimmer and edger. Compatible brands include Craftsman, Husqvarna, Weed Eater, and Poulan.

This kit includes all parts necessary to repair the carburetor on certain models of small engine outdoor power equipment.Internal combustion engines require a proper ratio of air to fuel in order to run. The carburetor is responsible for sending a combination of fuel and air to the motor for ignition. Because the carburetor is used every time the engine is started, it can deteriorate over time and may need to be repaired or replaced. Signs of a worn-out or deteriorating carburetor include backfiring, overheating, excessive black smoke, and reduced engine performance. This carburetor repair kit is a genuine OEM replacement part that has been sourced directly from the manufacturer. This carburetor repair kit can be used to fix various different models of Husqvarna, WeedEater, and Poulan blowers, trimmers, and hedge trimmers. Please note this part is sold individually.

This replacement part is a trigger and lockout kit intended for use in chainsaws. This is a genuine replacement part made by Husqvarna. Trigger and lockout kids are situated next to the handle at the top of the appliance. This part is one method of protecting the user from anything that can be harmful when using a chainsaw. It is made of durable plastic and metal. A new trigger and lockout kit might be needed if the current one is damaged or broken in any way. It is not unusual for this part to require replacement after years of normal use. Be sure the appliance is completely powered down and cooled off before attempting to replace this part. This is an OEM part sourced directly from the manufacturer. It is sold individually. This replacement part is compatible with chainsaws made by Husqvarna.

The clutch drum assembly seen here from Husqvarna is an important part of machines such as trimmers and pruners. The purpose of the clutch drum is to engage the clutch to spin the flex shaft and the cutting head. The clutch drum assembly could need to be replaced for many reasons. One of the most common signs is when the trimmer head stops spinning when it encounters weeds, grass, etc. Other signs include having a drive shaft that will not engage or a clutch that won't engage the drum. Sometimes, the lining in the clutch drum could become stripped, so there will be no torque when it is used. Replacing the clutch drum assembly can be a complicated task and will require a range of tools. Owners will also need to empty the fuel from the machine before they replace the clutch drum. This authentic clutch drum assembly is an OEM part from Husqvarna. It is sold individually and works for certain models of string trimmer and pole pruner. Brands that are compatible in addition to models from Husqvarna include Craftsman, Weed Eater, Poulan, and Poulan Pro.

This replacement oil tank for a pole pruner or chainsaw is an authentic OEM replacement part. The inner workings of an engine consist of many moving parts. These parts are mostly made of metal and they thrash about against each other to produce and transfer energy. Engines use oil to lubricate these parts so that they do not rub and create friction as this would cause the engine to overheat. This oil tank lets operators quickly top up their engines with oil without having to take apart the inner mechanics. Oil tanks are made of durable reinforced plastic but it is still possible to bang, dent, or even puncture them. Should this happen, oil will leak from the tank and the engine will be starved of lubrication. For safety purposes, it is important to immediately replace a broken oil tank. To do so, use a wrench to remove the old tank and install the new part with the same bolts. This oil tank is compatible with Poulan and some Husqvarna appliances, and as a high-quality replacement part, it comes sourced from its original manufacturer. This part includes an oil tank and oil tank cap but it does not include an oil line.

This authentic OEM part is a replacement momentary switch meant for a chainsaw or edge trimmer. Also known as a kill switch, a momentary switch acts as a safety measure to immediately shut off the appliance's motor. If the user begins to lose control of the appliance, they can simply hit the momentary switch and the engine will disengage even if it is not currently in the off position. This helps to prevent accidents and bodily harm. When engaged, the engine requires a five second waiting period before it can restart. Over time and through repeated use, switches can naturally become worn out. They may also be damaged if knocked against something hard on accident. Replacing this switch will require a screwdriver to access the switch located in the handle of the appliance. Once accessed, the switch can easily be replaced by detaching the wires and inserting the new part. Be sure to follow the user's manual as this process will vary depending on the appliance. This part is sourced directly from its original manufacturer and will work with Poulan and Weed Eater appliances. This part ships individually.

This replacement part is a line guide, and it is intended for use in different types of lawn equipment. This is a genuine replacement part made by Husqvarna. This line guide is small but aids in creating straight lines while cutting the grass in many different lawn mowers. A new line guide might be needed if the user notices the current one is not working properly. If the cutting lines of grass are not as straight as normal there might be an issue with the line guide inside of the machine. Be sure to wear working gloves while replacing this part as it is typically found near the blades of the appliance. This small part is sold as a single piece. This part is a genuine OEM part sourced directly from the manufacturer. Be sure to reference the specific owner's manual for more information on how to replace this part.