Poulan Parts

Fix a riding mower that won't start or has no electrical power with this protective fuse. Simple 5-minute replacement prevents electrical damage.

Replacement ignition key for walk behind lawn mowers. Starts and stops the engine. Needed when original key is lost, broken, or worn out.

This is a bellcrank ground drive intended for use with riding mowers, tractors, and trimmers. The bellcrank ground drive employs the idler pulleys when the pedal brake control shaft assembly is pressed. A new bellcrank may be needed if the original was faulty, or if it becomes significantly worn through general operation of the machinery. However, installation of a new bellcrank is relatively simple. Only a few tools will be required when replacing this item, including: a socket set, a set of pliers and a hex wrench. The removal of the mower deck will also be required. The user should refer to their owner's manual for guidance regarding their specific model.This is an OEM part sourced directly from the manufacturer. It is sold individually. The bellcrank ground drive is designed for use in Husqvarna, Poulan, Weed Eater, and Jonsered models.

Torsion spring for lawn tractor brake system. Installs on brake assembly to provide tension. Replace if broken, stretched, or missing for proper brake operation.

Spacer retainer for lawn tractors and riding mowers. Maintains proper spacing between components. Replace if cracked, broken, or missing during maintenance.

This is a flat metal washer used in lawn tractor assemblies to distribute load and prevent fastener damage on mounting points. It measures approximately 1.5 inches in outer diameter with a 0.505-inch inner hole and 0.118-inch thickness. Replace this washer if it is worn, corroded, or deformed, which can cause loose or rattling components.

This is a V-belt that connects the engine pulley to the mower deck pulleys, transferring power to spin the cutting blades on a riding lawn tractor. It is essential for engaging and driving the mower blades during operation. Replace this belt if the blades won't engage, the belt is cracked, frayed, stretched, or if you notice squealing or slipping when the blades are activated.

Replacement fuel tank cap assembly for chainsaws. Includes retainer to prevent dropping and contamination. Replaces cracked, broken, or missing caps.

This replacement part is an insert transfer and is intended for use in a variety of lawn equipment. This is a genuine replacement part made by Husqvarna. Insert transfers are small but very important to many different appliances like chainsaws. These parts reduce friction inside of the motor and piston. Without this part the engine could become damaged.A new insert transfer might be needed if the user hears noises coming from the equipment that are not normal. If there is excess heat coming from inside the appliance this might also be the cause. It is common that insert transfers become stripped overtime due to normal wear and tear. Be sure the equipment is completely powered down and cooled off before attempting to repair an appliance. For more detailed instructions on how to install this specific part, see the owner's manual. This is an OEM part sourced directly from the manufacturer. It is sold individually. This replacement part is compatible with different types of lawn equipment made by Husqvarna.

Chain overheating or binding? This oil pump plunger and gear assembly restores proper bar and chain lubrication. Fits over 125 chainsaw models.

Filters debris and water from fuel before it reaches your chainsaw's carburetor. Replace when clogged or cracked to prevent engine damage. Verify fit.

This recoil starter pulley kit includes the pulley used in the pull-start mechanism of a string trimmer. The pulley winds and releases the starter rope to engage the engine for starting. Replace this kit if the pull cord won't retract, feels loose, or the engine fails to turn over when the cord is pulled.

This part is a replacement isolation limiter screw. This is a genuine OEM part made by Husqvarna and has been sourced directly from the manufacturer. It is intended to replace a broken, stripped or defective isolation limiter screw in chainsaws.This isolation limiter screw helps to reduce movement and secure components of the chainsaw. It is a critical component that may become stripped, corroded, misplaced, or otherwise defective over time, requiring replacement. Wear work gloves to protect the hands and check that equipment is powered off and cooled down before starting the repair process. For more accurate information on how and where to use this isolation limiter screw, the appropriate owner's manual and equipment diagrams should be referred to. This isolation limiter screw is a genuine OEM part made of durable metal and is sold individually. It is suitable for use with chainsaw models that have been manufactured by Husqvarna, Poulan, and other brands.

Replacement fan baffle for gas line trimmers and pole pruners. Directs airflow for proper engine cooling. Replace if cracked, broken, or missing.

Leaf blower won't turn on or off? This momentary switch kit controls power to your handheld blower. Simple repair for worn or damaged switches.

Carburetor for gas leaf blowers. Mixes air and fuel for engine operation. Replace if cracked, leaking, or damaged to restore proper fuel delivery.