Poulan Parts

Carburetor for gas leaf blowers. Mixes air and fuel for engine operation. Replace if cracked, leaking, or damaged to restore proper fuel delivery.

Trimmer won't start or rope won't retract? This starter cup assembly rotates the flywheel to power your engine. Direct-fit part for many trimmers.

Controls spark timing in gas chainsaws. Replace if cracked housing, corroded terminals, or damaged wiring prevents proper ignition signal transmission.

Replacement shoulder harness for leaf blowers. Attaches to unit for comfortable wear during operation. Replace if straps are frayed, torn, or broken.

Engine won't start or runs rough? A faulty choke lever prevents proper cold starts. This replacement lever restores choke control for reliable starting.

This J tube is used to attach the vacuum tube to the vacuum bag. In order for the leaf blowers to function correctly, the tubing needs to be in prime condition to seal the air moving through the machine. This will enable full functionality of the blower. It's made of a durable black plastic, and will need to be replaced if cracking or warping is experienced. Exposure to elements as well as general use will lead to a need for replacement over time. Replacement is needed if visible cracks or drying is seen in the tubing, or if noticeable difference in amount of air moving through the vacuum component is hindering full use. Replacement is simple, and doesn't require tools. Separate the old part from housing, and replace it with the new part. This part is compatible with the Poulan and Weed Eater brand leaf blowers and gas powered leaf blowers. The wave washer is an OEM part sourced directly from the manufacturer, and it is sold individually.

Curved drive shaft houses the cable that connects engine to cutting head. Replace if bent, cracked, or damaged from impact. Provides maneuverability.

Fuel pickup assembly draws gas from tank to carburetor in gas chainsaws and trimmers. Replace if engine won't start or runs poorly. Verify fit with model.

Replacement fuel line kit for hedge trimmers. Installs in fuel system to transport fuel from tank to engine. Replace if cracked, brittle, or leaking.

Bar and chain not getting enough oil? This chainsaw oil pump assembly delivers proper lubrication to reduce friction and overheating during operation.

Hub spring for chainsaw recoil starters. Installs in the starter assembly to provide spring action for the pull cord mechanism. Replace if worn, bent, or broken to restore proper recoil function.

Replacement retainer ring for riding mower tractors. Secures components in place. Order when original is broken, cracked, or missing from assembly.

This rear handle is a genuine Husqvarna part, sold individually. This rear handle can be used as a replacement part for a chainsaw. A rear handle chainsaw can be used with one hand, whereas a top handle chainsaw must be guided with two hands.The rear handle of a chainsaw might have to be replaced in the event that the part has come loose, that the part does not function as usual as a steering grip, or that the part is damaged to the point that it cannot be repaired. If the rear handle has been torn, punctured, or eroded so it is rendered useless, the component should be removed and replaced by this genuine OEM replacement part. Remember to always wear gloves when handling, repairing, and operating outdoor equipment. Always unplug the appliance before performing any kind of repair or replacement.This is an OEM part sourced directly from the manufacturer. It is sold individually. This rear handle is compatible with the following outdoor appliance brands: Husqvarna and Poulan.

This 1/4-20 hex nut has a great variety of uses on lawn and landscaping equipment. As a lock nut, it can be tightened and retains its grip, even without the use of a washer. This particular piece of hardware appears in many connective points on push mowers, zero-turn mowers, riding mowers, tillers, lawn tractor implements, and other types of equipment manufactured by Husqvarna, Poulan, Jonsered, and Weed Eater. For instance, with MTD mulching mowers, these hex nuts are used to secure the mower housing to the manifold of the mower. More than just with gasoline-powered lawn tools, these versatile nuts are also found on handheld tools like impact wrenches and tools driven by compressed air. Hex nuts bind tightly with their locking grip and seldom come off. The more likely scenario, especially since so many are used in manufacturing and by power tools, is that these nuts will become lost in the course of maintaining, cleaning, and repairing mowers and other equipment. For this reason, it's always important for the user to purchase more than the anticipated number needed. Make sure also to purchase hex nuts like these that are OEM certified and guaranteed.

Deflector control cable for gas snowblowers. Connects control lever to discharge chute deflector. Replace if cable is frayed, broken, or binding.