Elaine April 18, 2013 for Model Number GU2300XTVQ1 The start/resume and the cancel/drain/buttons don't work. I can get all the other buttons to light up but it won't turn on. Do I need a control panel or circuit board? Thanks for any help I can get.
1 Answer Hello Elaine. Based on the information you provided, it sounds like the control panel WPW10175348 is bad and will need to be replaced. Read More...
Steve March 28, 2013 for Model Number GU2300xtv Control panel lights do not all work. If I push buttons randomly I can get almost all lights to go on and unit will cycle between wash and rinse several times and shut off. Very sporadic and changing action with lights. About 6 months ago cycle lights quit working properly but cycle I used still functioned. Bi-metal fuse checks at 0 ohms. New control panel? Is it returnable if it does niot fix problem? Thanks
1 Answer Steve, If the control lights are rotating around when the unit is cycling then it would more than likely be a problem with corrosion on the ribbon harness for the keypad or a bad keypad/control panel. Read More...
Jack January 22, 2013 for Model Number Maytag MDB8959AWB5 Dishwasher I replaced the soap dispenser(since the dispenser door would not open and dispense the soap).After running a complete cycle, the dispenser door does not open on the new dispenser. Do I need to replace additional parts? Please help. Thank you. Jack.
1 Answer Jack,You should be able to manually activate and move the latch lever to verify the latch works and the door opens. You'll need to run the diagnostic test mode, and check for 120 VAC on the wires to the dispenser solenoid with a multi meter. Otherwise you option is the check the two brown wires from the dispenser solenoid back to the control board. If the wires are OK, and tightly attached to the solenoid and control board connector, you'll need to replace the control board WPW10285179 . Read More...
Steve January 20, 2013 for Model Number kuds40fvss3 Dishwasher has had intermittent drainage failure. It now won't drain at all. I tried a new drain pump, but that didn't fix it. I am wondering about the control board. When I use cancel to force the drain cycle, there is an audible click but no pump activity. Voltage at the drain pump measures about 45 volts after the click from the control board. Do you know what the voltage to the pump should be? Does this sound like a board problem or might I have 2 bad pumps? Thanks,
1 Answer Hello Steve, The power coming to the pump should be 120 vac. If you are only getting 45 vac then you will want to check the wiring from the pump to control board and insure that there is not loose or broken wiring. If this checks ok the you would need new control board. Read More...
Giorgio December 28, 2012 for Model Number GU2300XtvQ1 Water fill valve does not open during the "Rinse and Hold" cycle, but it does open properly during nall other cycles. What could be the problem?
1 Answer Giorgio, Based on your post information, your most likely issue is a "glitch" in the control board fill valve circuit or the "chip" in the control board WPW10285179. You may want to try conducting the service diagnostic cycle to reset the control " To invoke the Diagnostics Cycle, perform the following key presses or actions in less than 6 sec while in standby: Heated Dry ? Normal ? Heated Dry ? Normal " allow the cycle to advance until it shuts off. " Invoking Service Diagnostics clears all status and last ran information from memory and restores defaults; It also forces the next cycle to be a sensor calibration cycle." If the issue persists, then replace the control board. Read More...
Bill D. December 11, 2012 for Model Number Whirlpool GU2300XTV/S2 We had a power outage from Hurricane Sandy. My dishwasher ran after power was restored, but now I have no power showing up on the control panel of the unit. Do I need a new control panel or circuit board or both for the unit. Please advise
1 Answer Bill, You may not need either part. First, check and make sure the electrical connections in the junction box on the dishwasher lower frame (behind the kick plate) have not shorted out or separated, due to the voltage spikes. Then check the control panel thermal fuse W10258275 and door switch WP8269209 circuits, a voltage spike can also effect these parts as well, and if either components are open or shorted, the dishwasher will act as if theres no power to it. Read More...
Dale November 27, 2012 for Model Number 665.13742K604 Regarding the main control board, is there a "core" credit to return the old control board to AppliancePartsPros? If so, what are the details? Also, what's the credit amount?
1 Answer Hello Dale, If you could call us at 1-877-477-7278 , one of our representatives will look it up for you and provide any pricing, shipping, etc... information you request. Read More...
Henry September 18, 2012 for Model Number KUDS301VBL3 I need to diagnose the control panel on my dishwasher. I just replaced it in February 2012. I could see the burnt area on the old one but I see no problem with this one. It stopped approx. halfway through a cycle and will now do nothing. No lights will come on, I tried to cancel but it did nothing, I reset the breaker and still nothing. I used a meter and know it has power going to it. Please help.
1 Answer Hello Henry. Based on the information you provided, it sounds like the thermal fuse W10258275 is bad and will need to be replaced in the unit. Read More...
David August 18, 2012 for Model Number 665.13842K603 Lights do come on but no control. Did run one cycle OK but won't work now. Lights still on until push cancel. When it ran the lights came on in a random pattern.
1 Answer Hello David. Based on the information you provided, it sounds like the control panel WPW10243209 is bad and will need to be replaced in the unit. Read More...
Jeff August 14, 2012 for Model Number 665.13744k603 I have no power to the buttons or lights on the front panel. The thermal fuse tests out good. What else can I check or is it likely the main circuit board?
1 Answer Hello Jeff. If the fuse is good, and there is power to the board, you will need to replace the board WPW10285179 in the unit. Read More...