Range Bumper, Bushing, Grommet Parts

Snap-in spacer for range installation. Provides proper spacing and alignment between components. Replace if cracked, broken, or missing to restore fit.

Rubber bumper for electric and gas ranges. Installs on the oven door to cushion closing and prevent damage. Replace if cracked, missing, or worn out.

Replace your range's spacer base if it's cracked, broken, or missing. This structural component helps maintain proper spacing and alignment between parts.

Spacer component that maintains proper distance between oven door window panes. Replace if broken, cracked, or missing to restore correct spacing.

Composite stud for range installation. Provides structural support and cushioning between components. Replace if cracked, broken, or missing during repair.

This rubber rangetop bumper cushions and supports the cooktop, reducing vibration and protecting the surface from metal-on-metal contact. It helps restore proper spacing and reduces rattling or chafing from loose or missing bumpers. What it does:

• Cushions the cooktop edge to prevent scratching and wear
• Keeps the cooktop and rangetop components properly spaced and stable
• Reduces rattling, vibration, and noise during use
• Commonly replaced when bumpers are cracked, flattened, missing, or allow movement

• Remove power to the appliance and allow all surfaces to cool before servicing.
• Access may require lifting or removing the cooktop; follow manufacturer instructions for your model.
• Replace with the same style bumper to maintain proper fit and spacing.
• Use care around sharp edges.

Spacer component for oven doors. Maintains proper door alignment and spacing. Replace if cracked, broken, or missing to restore correct door fit.

This snap bushing cushions and centers a rotating shaft or spacer, reducing wear and vibration for smooth appliance operation. Fits applications that require a 1.00 inch inside diameter and 1.468 inch outside diameter bushing. What it does:

• Provides a low-friction bearing surface to protect shafts and surrounding components from metal-on-metal wear
• Centers and stabilizes rotating parts to reduce vibration and noise
• Helps maintain proper clearance between moving parts for longer component life
• Used where a durable, press-fit snap bushing is needed for quick assembly

• One snap bushing

• Press into a clean, burr-free hole until the bushing snaps fully into place; do not force at an angle
• Verify correct orientation so the retaining lip seats against the mounting panel
• Replace any damaged or excessively worn bushings to prevent further component damage
• Disconnect power and follow appliance safety procedures before accessing internal components

This is a shelf support bushing that secures oven racks or shelves in place inside the oven cavity. It mounts to the interior side wall and provides a stable resting point for the rack. Replace this part if oven racks are tilting, sliding unevenly, or if the original support is cracked or missing.

A glass spacer used to position and support the cooktop glass where it mounts to the frame. Restores proper spacing and alignment for a secure, even fit on compatible Bosch cooktops. What it does:

• Keeps the cooktop glass properly spaced from the mounting frame to prevent rubbing or uneven gaps
• Helps maintain a stable, even surface for burners and cookware
• Reduces stress on the glass by providing an intended support point
• Can address symptoms like a misaligned or wobbly glass top and uneven gaps around the edge

• Intended for the specified cooktop mounting location; verify exact placement before installing
• Turn off power to the appliance and allow all surfaces to cool completely before service
• Handle glass parts carefully and use appropriate gloves to avoid cuts

This snap bushing is a push-in grommet that secures and protects wiring where it passes through sheet metal openings, helping prevent wire chafing and wear. It's a simple replacement that restores proper wire routing and protection. What it does:

• Holds wiring or harnesses in place at panel openings to prevent rubbing and abrasion
• Cushions wires against sharp edges to reduce the risk of wire damage and shorts
• Maintains correct wire routing to prevent pinching when panels are reassembled
• Common symptom: visible chafed insulation or loose wiring at an opening

• One snap bushing (quantity: 1)

• Disconnect power to the appliance before beginning any work to avoid shock or injury
• Access the panel or opening where the wiring passes through; remove any retaining screws or clips as needed
• Press the bushing into the hole until it snaps fully into place, then route the wire through the center
• Inspect surrounding wire insulation and replace or repair any damaged wiring before reassembly