Range Burner & Related Parts

Converts your gas range from natural gas to liquid propane. Includes orifices and instructions to adapt burner fuel type. Needed when switching fuel sources.

Small plastic cap that snaps into the center of range control knobs. Replaces cracked, missing, or worn caps to refresh appearance and protect knobs.

Pressure regulator for gas ranges and cooktops. Mounts to the gas supply line to control flow to burners. Replace if cracked, leaking, or missing.

This small cooktop bracket secures designated components beneath the cooktop surface, keeping them properly positioned and stable. Replace a damaged or missing bracket to restore alignment and reduce movement or rattling during use.

• Provides mounting support for specific under-top components, per model design
• Helps maintain proper alignment and stability of cooktop parts
• Replace when visibly bent, cracked, or corroded

• Disconnect power; for gas models, also shut off gas and allow the unit to cool
• Remove surface components as required (grates/caps/heads for gas; elements/panels for electric) to access under the top
• Lift or remove the cooktop as directed in your model's service information and secure the new bracket with existing hardware
• Reassemble, verify alignment, and for gas units check for leaks if any gas connections were disturbed

This circuit board mounting bracket secures an electronic board or module inside the appliance. It prevents movement, vibration damage, and wiring interference so the component stays correctly positioned for reliable operation.

• Mounts and supports a small circuit board or module within the chassis
• Maintains proper spacing and alignment to reduce chafing or electrical short risks
• Replace if bent, cracked, or missing tabs, or if it no longer holds the board securely
• Common signs include a loose/rattling board, visible bracket damage, or intermittent operation when the panel is bumped

• Disconnect power at the breaker; shut off gas supply if applicable
• Remove the necessary access panel(s) to reach the board and bracket; note orientation and wiring
• Transfer the board/module to the new bracket and reinstall using existing hardware
• Watch for sharp metal edges; route wires to avoid pinching and verify clearances before restoring power

Black burner cap for gas cooktops. Sits atop the burner head to distribute flame evenly. Replace if cracked, chipped, or missing for proper cooking.

LP gas conversion orifice kit for range top burners and oven. Includes orifices needed to convert from natural gas to propane. Essential hardware.

The Surface Burner Base is an OEM part for Frigidaire gas ranges. It provides a stable foundation and housing for the range's burners. Each burner base has a molded indentation to securely hold the burner assembly in place while cooking. 

Causes of a bad Surface Burner Base can include warping or distortion from overheating, cracks or punctures from impact or mishandling, or damage from corrosion over time.

Symptoms of a bad Surface Burner Base include: 

• Burners wobbling or moving out of position during use
• Gas or liquid leaks around burner housing 
• Irregular or uneven cooking performance 
• Loose, damaged, or missing burner assemblies

This genuine OEM Frigidaire base is also compatible with some Electrolux, Gibson, Kelvinator, and Kenmore models.

Snap-on burner cap for gas cooktops and ranges. Restores finished appearance and protects components. Replace if cracked, chipped, or missing.

Replacement burner head for gas cooktops. Distributes gas evenly through flame ports. Replace if damaged, clogged, corroded, or missing to restore burner.

Burner base mounts beneath the burner cap on gas range cooktops. Replace if cracked, corroded, or damaged to restore proper burner alignment and appearance.

Sealed burner assembly that supplies a protected gas flame for a gas range, restoring consistent heat and helping keep spills and debris out of the burner box. Designed as a direct-replacement assembly for affected burners. What it does

• Provides the sealed gas flame source used for cooking on a gas cooktop
• Restores even heat distribution when a burner is warped, damaged, or not producing a steady flame
• Helps prevent spills and food debris from entering the burner cavity, reducing corrosion and ignition problems
• Symptom linkage: commonly replaced for uneven heating, weak or irregular flame, visible burner damage, or excessive soot

• Includes 1 sealed burner assembly

• Turn off the gas supply and electricity to the appliance before starting any service
• Follow model-specific disassembly steps (lift or remove cooktop/grates as required); do not force fittings or gas connections
• If you smell gas, shut off the gas supply immediately

• WP3403M075-29 — confirm this matches your original part before ordering

LP bake burner orifice for gas range conversion. Replaces worn or incorrect orifice when converting to propane. Installs on bake burner assembly.

Protective burner cap that sits on top of the gas burner head. Replace if cracked, chipped, discolored, or missing to protect the burner assembly.

Replaces cracked or corroded sealed burner head on gas ranges and cooktops. Restores proper flame distribution when original part is damaged or clogged.

Replacement oven burner that restores heat in the oven's bake chamber so you can cook evenly. Installs in place of a damaged or worn burner to help the oven reach and maintain proper cooking temperatures. What it does:

• Produces the primary bake heat for the oven cavity.
• Replaces a cracked, corroded, or non-functioning burner that may cause weak or no heat.
• Helps correct uneven baking or failure to reach set temperatures when the burner is the source of the problem.

• Disconnect electrical power and shut off the gas supply before beginning work; follow all local codes.
• Use appropriate hand tools and avoid forcing parts; inspect sealing surfaces and connections for damage.
• If gas fittings or ignitors are involved, test for leaks after installation.